Jump to content
olouv

DSDT for a Dell Vostro 460 - i7 (lion)

2 posts in this topic

Recommended Posts

Hey, i've recently tried to setup an Hackintosh on a friend's computer.

 

It's a desktop Dell Vostro 460 with a core I7 inside.

 

Ran the "run_me.zip" program. Any idea what dsdt I could/use to make this work?

 

Main issue atm is no network.

 

Thanks a lot!

send_me.zip

Share this post


Link to post
Share on other sites
Advertisement

Any help would really be awesome... ! We are a small dev team in France stuck with theses desktop vostro in win7! Please free us!

 

If it can help, here is a PCWizard extract.

 

 

 

<<< Résumé Système >>>

> Carte Mère : Dell 0Y2MRG

> Chipset : Intel Sandy Bridge

> Processeur : Intel Core i7 2600K @ 3400MHz

> Mémoire physique : 4096Mo (2 x 2048 DDR3-SDRAM )

> Carte graphique : AMD RADEON HD 6450

> Disque dur : Seagate ST31000528AS (1000Go)

> Disque dur : Seagate ST3500641AS (500Go)

> Type de moniteur : Idek Iiyama PLT2250MTS - 22 pouces

> Carte réseau : Broadcom NetLink BCM57788 Gigabit Ethernet PCIe

> Système d'Exploitation : Windows 7 Professional Professionnel Media Center 6.01.7601 Service Pack 1 (32bits) > DirectX : Version 11.00

> Windows Performance Index : 5.0 sur 7.9

 

<<< Carte mère >>>

> Constructeur : Dell Inc.

> Carte Mère : Dell 0Y2MRG

> Bios : Dell Inc.

> Chipset : Intel Sandy Bridge

> Mémoire physique : 4096Mo DDR3-SDRAM

> Bus LPC : Oui

> Bus PCI : Oui

> Bus PCI-Express : Oui

> Bus USB : Oui

> Bus SMBus/i2c : Oui

> Bus HyperTransport : Non

> Bus QPI : Non

> Bus CardBus : Non

> Bus FireWire : Non

 

<<< Processeur >>>

> Processeur : Intel Core i7 2600K

> Fréquence : 3400MHz

> Nombre de Coeur : 4

> Support : Socket 1155 LGA

> Mémoire cache L1 : 4 x 64Ko

> Mémoire cache L2 : 4 x 256Ko

> Mémoire cache L3 : 8192Ko

> Tension VID : 1.500 V

> Coprocesseur FPU : Présent

> Coeur 1 Activité : 0%

> Coeur 2 Activité : 0%

> Coeur 3 Activité : 0%

> Coeur 4 Activité : 0%

 

<<< Affichage >>>

> Affichage actuel : 1920x1080 pixels à 60 Hz en couleurs vraies (32bits) 1

 

 

 

 

> Support Tactile : Oui

> Nombre de moniteur : 1

> Type de moniteur : Idek Iiyama PLT2250MTS

> Carte graphique : AMD RADEON HD 6450

> OpenCL : Non

> OpenGL : Oui

> GDI Plus : Oui

> Direct2D : Oui

 

<<< Ports >>>

> Type de port installé : Intel® 6 Series/C200 Series Chipset Family USB Enhanced Host Controller - 1C2D > Type de port installé : Intel® 6 Series/C200 Series Chipset Family USB Enhanced Host Controller - 1C26

<<< Lecteurs >>>

> Nombre de Contrôleur Disque : 1

> Nombre de contrôleur Disque USB : 1

> Nombre de disque dur : 2

> Nombre de lecteur CD-Rom : 0

> Affectation des lecteurs : C: D:

> Lecteur C: (Disque dur) : 633 Go disponibles sur 718 Go

> Lecteur D: (Disque amovible) : 0 Ko disponibles sur 0 Ko

 

<<< Imprimantes >>>

> Imprimante par défaut : \COPERNICHP LaserJet 4250 PCL 6

> Imprimante installée : Microsoft XPS Document Writer

> Imprimante installée : Fax

> Imprimante installée : \COPERNICHP LaserJet 4250 PCL 6

> Pilote universel : Non installé

 

<<< Périphériques >>>

> Type desouris : Périphérique d’entrée USB

> Type declavier : Périphérique d’entrée USB

> Manette de jeu : Aucune

> Périphérique HID : Oui

> Périphériques UPnP : 3

> SCSI Host #0 : 2 Périphériques

> Disque : Verbatim STORE N GO USB Device

> Biometric : Non

> Trusted Platform Module : Non

 

<<< Multimédia >>>

> Périphérique audio : Dell Computer Cougar Point High Definition Audio Controller

> Périphérique audio

> Reproduction audio : Realtek Digital Output (Realtek

> Reproduction audio : Mappeur de sons Microsoft

> Sortie Midi : Microsoft GS Wavetable Synth

> Sortie Midi : Microsoft MIDI Mapper

> Périphérique de mixage : Realtek Digital Output (Realtek

> Périphérique multimedia : AVIVideo

> Périphérique multimedia : CDAudio

> Périphérique multimedia : Sequencer

> Périphérique multimedia : WaveAudio

> Périphérique multimedia : MPEGVideo

> Compression audio : Codec Microsoft IMA ADPCM

> Compression audio : CODEC A-Law et u-Law Microsoft CCITT G.711

> Compression audio : Codec audio Microsoft GSM 6.10

> Compression audio : Codec Microsoft ADPCM

> Compression audio : Fraunhofer IIS MPEG Layer-3 Codec (decode only)

> Compression audio : Messenger Audio Codec

> Compression audio : Convertisseur PCM Microsoft

 

 

2

 

<<< Réseau >>>

> Réseau : Oui

> Connexion Internet : Oui

> Connection RAS : Non

> Passport.Net : Non

> Winsock32 : v2.02

> Connexion Réseau : VMware Network Adapter VMnet1 > Connexion Réseau : VMware Network Adapter VMnet8 > Connexion Réseau : Connexion au réseau local

> Connexion Réseau : Hamachi

> Connexion Réseau : VirtualBox Host-Only Network

> Serveur IIS : Non

> Carte réseau : VirtualBox Host-Only Ethernet Adapter

> Carte réseau : Broadcom NetLink Gigabit Ethernet > Routeur Internet : Netgear DG834 Router

> Partage : 4 Ressources

> Réseau local : 29 Ordinateur réseau

> Groupe Local : 15

 

<<< Gestion d'énergie >>>

> Gestion d'énergie : Oui

> Batterie : Non

> Alimentation : Secteur

> Gestion d'alimentation actif : Performances élevées

> ACPI Tables : 11

 

<<< Tension, Température et Ventilateur >>>

> Voltage Processeur :

> Voltage : 0.99 V

> Processeur Intel Core i7 : Capteur DTS

> Coeur 1 : 33 °C

> Coeur 2 : 29 °C

> Coeur 3 : 30 °C

> Coeur 4 : 30 °C

> AMD RADEON HD 6450 : ATI Catalyst Driver

> Température : 47 °C

> Ventilateur : 36.0%

 

<<< Index Matériel de Windows >>>

> Performance Globale : 5.0 sur 7.9

> Performance Processeur : 7.6 sur 7.9

> Performance Globale Mémoire : 7.6 sur 7.9

> Performance Graphique : 5.0 sur 7.9

> Performance Jeux : 6.3 sur 7.9

> Performance Disque Dur : 5.9 sur 7.9

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By tonyx86
      This thread for installing Catalina on the Dell Latitude E6410 WITH NVIDIA GRAPHICS (BIOS A17, NVidia 3100m) will help you install a fresh installation of Catalina on your Dell Latitude E6410, it will help you upgrade from 10.15.2 to 10.15.x (if you originally installed Catalina from this thread) and it will also help you upgrade from Mojave 10.14.6 if you have already installed Mojave by following the instructions here.  The instructions in this first post assume that you are installing Catalina in an APFS container.  If you are curious about the evolution of this solution and how sleep/wake was solved, review the Mojave installation thread.
       
      Important: This Thread is NOT intended to help you install macOS on a Latitude E6410 with Intel HD Graphics (without Nvidia graphics).  The DSDT attached to this first post (in E6410-Catalina.zip) is VERY SPECIFIC to the Nvidia graphics implementation and has not been edited for HD Graphics - there are elements required for HD Graphics that are missing from the attached DSDT and there are DSDT mods that have not been tested with HD Graphics.  Also, the kexts attached to this first post are specific to a Broadcom Wi-Fi card which must replace the original Intel Wi-Fi card.
       
      This first post will be modified to reflect lessons learned and to reflect the most current working state of my Latitude E6410 (with NVidia 3100m discrete graphics) running Catalina.  Issues, observations and performance tips are recorded toward the bottom of this first post.  My recommended CLOVER configuration is specified toward the bottom of this first post.
       
      *** If you want help with your installation, please post your issue along with problem reporting files generated using @black.dragon74's problem reporting tool.  Google 'GENERATE PROPER PROBLEM REPORTING FILES black.dragon74' to find it. ***.  If Catalina's Read-Only protections block your installation of black.dragon74's gen_debug script, please copy the attached gen_debug script to your Desktop, change script properties with the terminal command 'chmod a+x ~/Desktop/gen_debug' and run the script from your Desktop.
       
      My system is as follows:
      Dell Latitude E6410 (I7-620m, Nvidia 3100M, 8GB DDR3, 512GB SSD, 1440x900 display, BIOS: A17) Wi-Fi: Broadcom BCM 94352HMB (replaced original Wi-Fi card) BIOS (version A17) configured as follows (leave default unless listed here): Boot Sequence: USB, Internal HDD, CD/DVD, Modular Bay HDD; Boot List Option: Legacy; Integrated NIC:Enabled; Parallel Port: Disabled; Serial Port: Disabled; SATA Operation: AHCI; Misc Devices: Enable Modular Bay, Camera, External USB, Microphone, Media Card and 1394; Latitude ON Reader: Disabled; Keyboard Illumination: Auto ALS and Input; Ambient Light Sensor: Enabled; OROM Keyboard Access: Disable; TPM Security: Disable; Computrace:Deactivate; CPU XD Support: Enable; Performance: Enable all options; Power Management: Disable Wake on AC, Disable Wake on LAN/WAN, Express Charge: Standard, Charge Behavior: Enabled; Keypad: Fn Key Only; Mouse/Touchpad: Touchpad/PS-2 Mouse; USB Emulation: Enable Legacy; Fn Key Emulation: Disabled; Fastboot: Thorough; Virtualization: Enable Intel Virtualization, Disable VT for Direct I/O, Disable Trusted Execution; Wireless Switch: Bluetooth and WLAN; Wireless Device Enable: Bluetooth and WLAN;   
      Versions of the software used in this installation are listed below the installation steps.  EFI and kexts for Catalina are attached to this first post in E6410-Catalina.zip.  CLOVER configuration is specified below the installation steps.
       
      Wi-Fi connection to an Access Point is delayed when using AppleALC for sound.  Do not use Apple ALC.  Use VoodooHDA pkg 2.9.2 v15 for sound.
       
      Steps to install Catalina on a Dell Latitude E6410 (BIOS A17, NVidia 3100m)
       
      If you want to upgrade to 10.15.5, see instructions at this post.
       
      If you want to upgrade to 10.15.4, see instructions at this post.  
       
      Follow instructions below for 10.15.2 and 10.15.3.
       
      Make sure that your system matches my system description above (including BIOS version, Wi-Fi card, BIOS settings) If performing an upgrade from Mojave or a previous version of Catalina, backup your Mojave or Catalina partition! (Carbon Copy or similar) Download Catalina Installer Download DosDude Catalina Patcher Use DosDude Patcher to create Catalina USB Installer Delete LegacyUSBInjector.kext (we're using @RehabMan's USBInjectAll.kext with custom SSDT) and delete SIPManager.kext (CLOVER is managing SIP) from Catalina USB Installer's /Library/Extensions folder Copy all but the FakeSMC sensor kexts in E6410-Catalina.zip (attached) LE folder to the Catalina USB Installer /Library/Extensions (copy all kexts (including FakeSMC.kext) but not the FakeSMC sensor kexts) Install CLOVER Bootloader (Legacy) on USB Installer using the EFI in the E6410-Catalina.zip (attached).  Use the CLOVER configuration specified below.  Be sure to replace the XX-MASKED-XX parameters in the attached config.plist with your own values. Reset your Latitude E6410 NVRAM by doing the following (this may be important if you're making changes to your existing EFI and won't hurt anything if you're not making any changes) turn-off your laptop remove A/C power and main battery press and hold the power button for 30 seconds restore A/C power and battery Boot your Latitude E6410 from the Catalina USB Installer that you created in steps 5-8. Select "Reinstall macOS" (note that I have existing installations of Mojave and High Sierra on my Latitude E6410, so it's possible that this menu item changes to "Install macOS" if you don't have any previous macOS installations). Select your Catalina destination partition (which will be your Mojave or previous Catalina partition if you are upgrading) After the Catalina Installer reboots the first time, boot from the "macOS Installer" partition on the disk that you selected as your Catalina destination (not the macOS installer on the USB) After the Catalina Installer reboots the second time, boot the Catalina macOS Installer on the USB Select the Post Install Patcher utility Select only the following Post Install Patches (no other patches / options) Install Patch Updater Legacy Video After the Post Install Patcher reboots,  boot from the newly installed (or upgraded) Catalina partition and complete the macOS configuration Remove these kexts (if they exist) from /Library/Extensions: LegacyUSBInjector.kext, LegacyUSBVideoSupport.kext and SIPManager.kext If you are performing a fresh installation of Catalina: Install CLOVER (LEGACY - NOT UEFI) on your boot disk and configure EFI using files in the attached E6410-Catalina.zip.  Use the CLOVER configuration below.  Be sure to replace the XX-MASKED-XX parameters in the attached config.plist with your own values. Install all kexts in the attached E6410-Catalina.zip LE folder to your /Library/Extensions folder. Copy HWMonitor from the application folder in the attached E6410-Catalina.zip to your Applications folder. Install VoodooHDA (I installed using the Classic method) Skip to Step 21 If you are upgrading from a previous version of Catalina using the instructions from this thread or from Mojave that you installed using the instructions here: Replace 3rd-party kexts in EFI/Clover/kexts/Other with those in the attached EFI folder.   Replace EFI/Clover config.plist with the attached config.plist (Be sure to replace the XX-MASKED-XX parameters in the attached config.plist with your own values) Replace EFI/Clover/ACPI/patched with the files in the attached EFI/Clover/ACPI/patched Replace 3rd-party kexts in /Library/Extensions with those in the attached LE folder Remove VoodooSDHC.kext from /Library/Extensions Re-install VoodooHDA if necessary (I installed using the Classic method for Catalina) Ensure PROPER kext installation: If you're manually installing kexts in /Library/Extensions, make sure that you execute the following (in terminal) cd /Library/Extensions sudo chown -R root:wheel *.kext sudo chmod -R 755 *.kext sudo kextcache -i / After you execute 'sudo kextcache -i /' you should observe that ALL kexts are allowed.  If not, your kext directory attributes are probably incorrect.  Repeat kext installation and try again. Reboot from your new/upgraded Catalina partition Welcome to macOS Catalina! Change the keyboard type to ISO (System Preferences > Keyboard > Change Keyboard Type) Swap the Command and Option keys (System Preferences > Keyboard > Modifier Keys) Set hibernatemode: In terminal, execute sudo pmset -a hibernatemode 0 sudo rm -f /var/vm/sleepimage sudo touch /var/vm/sleepimage sudo chflags schg /var/vm/sleepimage  
      Version Info at the time of this writing:
      Catalina Installer 10.15.5 CLOVER r5118 DosDude Catalina Patcher: v1.4.3 Lilu.kext 1.4.4 AirportBrcmFixup.kext 2.0.6 BrcmFirmwareData.kext 2.5.3 BrcmBluetoothInjector.kext 2.5.3 BrcmPatchRAM3.kext 2.5.3 IntelMausi.kext 1.0.2 (Not IntelMausiEthernet.kext)
      EFICheckDisabler.kext 0.5
      VoodooHDA.kext 2.9.2 v15 (NOT AppleALC)
       
      What is not working (that was working in Mojave)
      SD Card Slot (had to remove VoodooSDHC.kext which caused system freeze on wake)  
      Known Issues and Their Solutions
      (Solved - no further work required) Clover r5118 requires the config.plist key <key>NoDefaultProperties</key><false> to permit macOS to boot with Clover's "Inject Nvidia" = True.  See details here.  config.plist in the attached E6410-Catalina.zip archive includes this change. (Solved - no further work required) EFICheck is loaded.  Solution is to install EFICheckDisabler.kext which you can get here.  EFICheck.kext is included in the attached E6410-Catalina.zip archive. (Solved - no further work required) Some users experience display issues.  The solution is to remove Device (PNLF) from the DSDT.  Use the attached DSDT.  Removal of PNLF will disable sleep on lid closure.  Device (PNLF) can be added without modifying the DSDT by enabling the Clover PNLF ACPI patch.  The attached Clover config.plist enables the PNLF DSDT patch.  Disable the Clover PNLF patch if you experience display issues. (Solved - no further work required) USB sleep/wake power IORegistry keys are not injected (not included in Mojave's or Catalina's IOUSBHostFamily.kext).  Solution is to added SSDT-USBX.aml to EFI/CLOVER/ACPI/patched.  The attached SSDT-USBX.aml includes USB sleep/wake properties for MacBookPro6,2 from High Sierra 10.13.6 IOUSBHostFamily.kext. (No solution yet) Brightness slider does not work in System Preferences > Displays.  Brightness is easily controlled with Dell brightness keys.  There is some work on this later in this thread, but I will not be solving this as I'm content with the Dell brightness keys (and Ambient Light Sensor works to auto-adjust brightness). (No intention to solve) Display Settings in System Preferences are "garbled" when bright slider is visible.  This is a known issue with the legacy graphics patch and does not affect laptop operation. I continue to refine the DSDT and CLOVER config.plist to optimize my Latitude E6410 for multi-booting between various macOS versions (High Sierra, Mojave and Catalina at the time of this writing). If you upgrade your Latitude E6410 EFI using my attached EFI, you may find that your Latitude E6410 is stuck in a boot-loop that ends in a white screen and reboots.  Clear your system by doing the following: turn off your laptop, remove A/C power, remove the main battery, press and hold the power button for 30 seconds, restore A/C power and battery, boot normally.  I have only found this to be necessary (very rarely) after making an EFI change, but you may find it helpful if making kext changes in /Library/Extensions as well. (Solved - no further work required) Brcm firmware does not update when using BrcmFirmwareRepo.kext in /Library/Extensions.  Solution is to install BrcmFirmwareData.kext and BrcmPatchRAM3.kext in E/C/k/O with Clover "Inject Kexts" = YES. (Solved - no further work required) Laptop does not sleep when closing lid.  Solution appears to be a combination of adding Notify (LID0) code to Method (BTNV) and adding Device (PNLF) in the DSDT. I am using the same EFI for High Sierra 10.13.6, Mojave 10.14.6 and Catalina 10.15.3 and it works in all three macOSes. (No solution yet) No SD Card Slot (had to remove VoodooSDHC.kext) - I read somewhere that there is a solution that does not require any kexts (just a DSDT edit).  Haven't yet implemented this fix. (Not a problem that needs to be solved - leaving for historical purposes.  I am running Catalina without this.) - IOHWControl does not load under GFX0 (as observed in IORegistryExplorer).  Solution (if it needs to be solved) is to install AppleHWSensor.kext from a DosDude-patched Mojave /S/L/E in Catalina's /L/E.  Copy and install your own or use the kext attached to this post. (Solved - no further work required) Wi-Fi connection is delayed until a minute or so after boot - Use VoodooHDA and NOT AppleALC (Solved - no further work required) External USB ports do not work after waking from sleep (S3) - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Boot and shut-down time of Catalina is slower than Mojave - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Wi-Fi is not immediately available at OS startup - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Laptop freezes on wake - Remove VoodooSDHC.kext from /Library/Extensions  
      Tips for Improved Performance (on this and other older systems)
      System Preferences > Spotlight > Search Results: Uncheck all options System Preferences > Spotlight > Privacy: Add all Volumes System Preferences > Accessibility > Display: Check "Reduce motion" System Preferences > Accessibility > Display: Check "Reduce transparency"  
      Other tips
      If your fan is always running and temps are good, try pressing Fn + z (I haven't noticed this issue for a while since I completed DSDT edits for Mojave, but keeping this here for historical purposes)  
      CLOVER Installation: Use these configuration options (Install Clover LEGACY - NOT UEFI)
      Install Clover in the ESP Boot Sectors Install boot0af in MBR Clover for BIOS (LEGACY - NOT UEFI) booting Clover EFI 64-bits SATA BIOS Drivers, 64-bit Recommended drivers FSInject File System drivers ApfsDriverLoader Install RC scripts on target volume Themes Choose your desired theme Install Clover Preference Pane After clicking "Continue", if prompted with "This Clover package is incompatible with this version of macOS," install anyway  
      After CLOVER installation is complete Copy the following from the attached E6410-Catalina.zip ACPI patched contents config.plist (change XX-MASKED-XX values to your own) kexts/Other (remove all other kext folders) Remove christmas and new year folders from themes (if present)  
      Credits
      Thanks to those who contributed to my Mojave solution and to the DosDude team (for the incredible macOS patchers), I think this Catalina installation was the easiest macOS installation that I have experienced (so far).  Many thanks to @Slice and his team for the incredible work on CLOVER and for continuing to support old legacy systems like this.  Also, thanks to @Mieze and @headkaze and others I'm sure for maintaining the Brcm kexts.  And finally, I still prefer to manually apply patches to the DSDTs in my systems.  CLOVER offers extensive patching functionality, but I'm old-school and like to have an error-free, fully-patched DSDT with a simple CLOVER config.plist.  I think that this manual DSDT patching approach (which required an extensive review and debugging of the original unpatched DSDT in this thread) is the reason that this Latitude E6410 is such a perfect MacBookPro6,2.  Thank you @RehabMan for being a great teacher and for always insisting on problem reporting files .
       
       

      AppleHWSensor.kext.zip
      gen_debug

      E6410 Catalina-5v1.zip
    • By MaLd0n
      -Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      -Donations with Bitcoin
      33HeGCuCSh4tUBqdYkQqKpSDa1E7WeAJQ3
       
      -Donations with PicPay 
      @danielnmaldonado
       
      -Donation with Mercado Livre 
      https://tinyurl.com/y9evkj5u
       
       
      --Original Topic--
      https://www.olarila.com/topic/6874-olarila-hackbook-lenovo-ideapad-s145-mojave-catalina-full-dsdt-patches/
       

       
      -Perfect HackBook, HDMI Audio/Video, Bluetooth, AirPlay, Sleep, Lid Sleep, Auto Sleep, Audio, etc!
      -Wifi card has been replaced with Dell DW1560!
      -I'm using a S145-15IWL Model with Intel Core i5 8265u / Intel UHD Graphics 620
      -Update bios/uefi to last version
       
      --Installation--
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
       
      --Clover Folder--
      https://tinyurl.com/rkqmpd9
       
      --OpenCore Folder--
      https://tinyurl.com/y75hqg7z
       
      Bluetooth Broadcom
      Bluetooth Broadcom.zip
       
      CPUFriend for i5-8265U
      CPUFriend i5-8265U.zip
       
      --Full DSDT Patches--
      -My DSDT
      DSDT Lenovo IdeaPad S145.zip
       
      This DSDT work on S145-14IWL, S145-15IWL, V14-IWL, V15-IWL models
      -Patches
      -FIX ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 11 ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PRWs -_DSMs -PNLF -BRIGHTNESS KEYS -I2C -NATIVE USB -ARPT -GFX0 -DTGP -kUSBCompanionIndex -io-device-location -FULL RENAMED DEVICES   --IGPU Patch--
      Video solution with HDMI Audio and Video
      <key>PciRoot(0x0)/Pci(0x2,0x0)</key> <dict> <key>AAPL,GfxYTile</key> <data> AQAAAA== </data> <key>AAPL,ig-platform-id</key> <data> CQClPg== </data> <key>device-id</key> <data> pT4AAA== </data> <key>enable-hdmi20</key> <data> AQAAAA== </data> <key>framebuffer-con0-alldata</key> <data> AAAIAAIAAACYAAAA </data> <key>framebuffer-con0-enable</key> <integer>1</integer> <key>framebuffer-con1-alldata</key> <data> AQEJAAAIAADHAQAA </data> <key>framebuffer-con1-enable</key> <integer>1</integer> <key>framebuffer-con2-alldata</key> <data> AgYKAAAEAADHAQAA </data> <key>framebuffer-con2-enable</key> <integer>1</integer> <key>framebuffer-fbmem</key> <data> AACQAA== </data> <key>framebuffer-patch-enable</key> <data> AQAAAA== </data> <key>framebuffer-stolenmem</key> <data> AAAwAQ== </data> <key>framebuffer-unifiedmem</key> <data> AAAAgA== </data> <key>hda-gfx</key> <string>onboard-1</string> <key>model</key> <string>Intel Corporation, Iris Plus Graphics 655</string> </dict>   --Native USB Fix for Notebooks - No Injector/Kext Required--
      https://www.olarila.com/topic/6878-guide-native-usb-fix-for-notebooks-no-injectorkext-required/
      https://www.olarila.com/topic/6181-guide-native-usb-fix-for-desktops-no-injectorkext-required-skylake/
       
       
      -ScreenShots

































      -Links
       
       
      Clover https://github.com/CloverHackyColor/CloverBootloader
      AirportBrcmFixup.kext https://github.com/acidanthera/AirportBrcmFixup
      AppleALC.kext https://github.com/acidanthera/AppleALC
      Brcm Bluetooth https://github.com/acidanthera/BrcmPatchRAM
      Lilu.kext https://github.com/acidanthera/Lilu
      SystemProfilerMemoryFixup.kext https://github.com/Goldfish64/SystemProfilerMemoryFixup
      VirtualSMC.kext https://github.com/acidanthera/VirtualSMC
      VoodooI2C.kext https://github.com/alexandred/VoodooI2C
      VoodooPS2Controller.kext https://github.com/acidanthera/VoodooPS2
      WhateverGreen.kext https://github.com/acidanthera/WhateverGreen
      MaciASL - https://github.com/acidanthera/MaciASL
      acpica - https://github.com/acpica/acpica
      AptioMemoryFix.efi https://github.com/acidanthera/AptioFixPkg
      ApfsDriverLoader.efi https://github.com/acidanthera/AppleSupportPkg
      HFSPlus.efi https://github.com/JrCs/CloverGrowerPro/blob/master/Files/HFSPlus/X64/HFSPlus.efi?raw=true
      Hackintool https://github.com/headkaze/Hackintool
       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
       
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
       
      We're all here to have fun and learn from each other!
    • By MaLd0n
      -Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      -Donations with Bitcoin
      33HeGCuCSh4tUBqdYkQqKpSDa1E7WeAJQ3
       
      -Donations with PicPay 
      @danielnmaldonado
        Install MacOS with Olarila Image, Step by Step, Install and Post Install
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
        First... If you need DSDT edits... -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation --Create a bootable copy of El Capitan /  Sierra / High Sierra / Mojave https://github.com/chris1111/Create-Install-Media/releases   --Install Clover in USB stick https://github.com/CloverHackyColor/CloverBootloader/releases   --Replace with my Clover folder https://www.olarila.com/topic/5676-clover-folder-for-all-chipsets/   --Install EL Capitan / Sierra / High Sierra and boot into system!     Post Installation   --Install Clover and replace with my folder   https://www.olarila.com/topic/5676-clover-folder-for-all-chipsets/     --Reboot and activate video!   Bingo! Now you need a fine tune! DSDT Time!   My DSDT GA P35-DS3   DSDT.MaLd0n.zip     Patches -FIX ERRORS AND WARNINGS -HPET -SATA -SLPB -DARWIN -LPC -HDEF -RTC -EHCI -UHCI -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -EC -PNLF --Native Power Management
       
      Use Clover, check Generate P and C States
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --AUDIO
       
      Device HDEF + AppleAlc + Lilu
       
      --install Lan driver by Mieze
        -Atheros   http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel   http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek   http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC   https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio   https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/293863-applehda-patch-requests/   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!   ENJOY!  
    • By MaLd0n
      -Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      -Donations with Bitcoin
      33HeGCuCSh4tUBqdYkQqKpSDa1E7WeAJQ3
       
      -Donations with PicPay 
      @danielnmaldonado
        Nehalem, SandyBridge, IvyBridge, Haswell, Broadwell   https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/   Skylake, Kabylake and Coffeelake is here https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/   Install MacOS with Olarila Image, Step by Step, Install and Post Install
       
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
          First...   ***Update bios to last available version!***   If you need a full patched DSDT...  -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation   --Create a bootable copy of macOS Sierra / High Sierra / Mojave   https://github.com/chris1111/Create-Install-Media/releases   --Install Clover in USB stick   https://github.com/CloverHackyColor/CloverBootloader/releases   --Replace with my Clover folder https://www.olarila.com/topic/5676-clover-folder-for-all-chipsets/   --Install Sierra/High Sierra and boot into system!   Post Installation --Install Clover and replace with my folder   https://www.olarila.com/topic/5676-clover-folder-for-all-chipsets/   --Reboot and activate video!   Bingo!   Now you need a fine tune! DSDT time!   --DSDT   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC -XHCI -PLUGIN TYPE -XXXX to HDEF -HDEF -RTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -EC -PNLF -HDMI
       
      --Power Management
      - 1 Generation Intel Processors, use Generate P and C States in config.plist
      - 2 and 3 Generations Intel Processors, Generate SSDT with Piker script and drop CpuPm and Cpu0Ist SSDTs
      ssdtPRGen.command.zip
      Credits-https://github.com/Piker-Alpha/ssdtPRGen.sh
      - 4 Generation+ Intel Processors, use PluginType=1 in DSDT, SSDT or Clover config.plist
       
      for check Power, Frequency, Temperature and Utilization, use it
       
      Install Intel Power Gadget.pkg.zip
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --Clover
       
      https://sourceforge.net/projects/cloverefiboot/files/Installer/
       
      --AUDIO
       
      Use DSDT + AppleAlc
       
      --install Lan driver by Mieze
        -Atheros   http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel   http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek   http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC   https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio   https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/314406-voodoohda-289/   -USB   https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads   It's time to Rock   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Apple, Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!  
    • By Kailash
      I successfully managed to install Hackintosh on my Lenovo Ideapad 520 but now I don't have audio, brightness control feature or battery indicator. My audio driver is an ALC230. I am new to all this. What do I do to solve this? I have attached my EFI files below.
      EFI.zip
×