Jump to content
Sign in to follow this  
Followers 0
Q-Dog

Hackintosh on a Thinkpad Edge 13 (K685)...Will it work?

1 post in this topic

Recommended Posts

Hi everyone,

 

I was wondering if it is possible to run Snow Leopard or Lion on a Lenovo Thinkpad Edge (K685) or if the complications (especially AMD) are too high?

 

Here is the datasheet:

 

  • Processor : AMD Turion II Neo K685 1.8 GHz
  • Mainboard : AMD M785
  • Memory : 4096 MB, 2x 2048MB
  • Graphics adapter : ATI Radeon HD 4225 - 256 MB, Core: 382 MHz, Memory: 400 MHz, Catalyst 9.7; 8.632.1.2000
  • Display : 13.3 inch 16:9, 1366x768 pixel, LP133WH2-TLM3, glossy: no
  • Harddisk : Hitachi HTS725050A9A364, 500GB 7200rpm
  • Soundcard : ATI RS690 HDMI @ ATI SB800
  • Connections : 3 USB 2.0, 1 VGA, 1 HDMI, 1 Kensington Lock, 1 eSata, Audio Connections: Audio in/out combi, Card Reader: 5-in-1 cardreader (SD (SDHC), MMC, MS, MS Pro, xD),
  • Networking : Realtek RTL8168D/8111D Family PCI-E GBE NIC (10/100/1000MBit), 802.11 b/g/n (bgn), 2.1 +EDR Bluetooth

 

Thanks in advance

 

Cheers Q-Dog

Share this post


Link to post
Share on other sites
Advertisement

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
Followers 0

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By RoroMush
      Hi Guys,
       
      I was finally able to get my Catalina installer to boot using by changing EC0 to EC 4543305f 45435f5f. Huge headache with this as it took me a good couple of days to fix the error. 
       
      The good news is I can make it to the installer but now the problem is now the Catalina installer gets stuck at 2 minutes with the error code showing disk25s1 is not convertible to APFS.
       
      My Troubleshooting Steps:
       
      - Tried another NVMe drive, with same results
      - Checked Samsung Magician for updates, no luck
      - Formatted the drives in Ubuntu, same exact installer error.
       
      For some reason the disks always show as "Writable: NO" 
       
      Hardware:
      - Asus Z390-E 
      - Intel i7 9700K
      - Samsung 970 Pro
      - 16GB Crucial 
      - Intel UHD Graphics
       
      Is there something wrong with my kexts or config? 
       
      Thank You!
       
       
       
      EFI.zip

    • By AudioGod
      I have put together this simple little guide for anybody wanting to use a Patched DSDT EFI with the same configuration as me.
      This is also a thread to discuss everything Z390 Pro and try and help where we can and maybe make things a little better for you. 
       
      A huge massive thank you to @glasgood @MaLd0n @larabee These three guys have helped me and talked me so much and are as helpful as you could ever get, Without them I wouldn't have a perfect working build like I do or be putting up this Guide & Discussion Thread sharing the hard work and countless hours that we have all put in to this.   
       
       
      This EFI and Patched DSDT have been created to work with a Gigabyte Aorus Z390 Pro, 9900k with a Vega 56 but has also been tested and verified fully working with the following Hardware using Catalina 10.15.4
       
      CPU's
      8700k, 9600k, 9700k, 9900k
       
      GPU's
      RX 560, 570, 580, 590, Vega 56, Vega 64, Radion VII, 5700, 5700 XT
      (If you have success with any different CPU or GPU's then please do let me know)
       
       
       @glasgood Has kindly put together a new simple Catalina install guide so Just Follow He's Guide For a Perfect Install.
       
       
      HARDWARE USED
      • Intel I9 9900k 
      • Gigabyte AORUS Z390 PRO
      • Sapphire Nitro+ SE Vega56 (connected to monitor with DisplayPort)
      • Corsair Vengeance Pro RGB 16GB @3200mhz (2 x 8GB)
      • Corsair RM850x 80 Plus Gold Power Supply Unit. 
      • CoolerMaster MASTERLIQUID ML360R RGB CPU Cooler
      • Samsung 970 EVO 1TB NVMe SSD macOS Catalina 10.15.3
      • Samsung 860 EVO 1TB SSD (2.5) Windows 10 Pro
      • ABWB BCM943602CS 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E)   
      • Lian Li PC-O11DW Dynamic ATX Case
       

       

       

       

       
       
      WORKING
      • Sound 
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 (All ports Open Natively)
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Sleep & Wake
      • Sleep and Shutdown via the Power Button
      • Handoff
      • Netflix on Safari browser
      • Continuity
      • Sidecar
       
       
      CLOVER  FOLDER
      Use this folder with fully patched DSDT
      Current EFI 
      Updated 06/04/2020
      PLEASE NOTE - You MUST update to the latest EFI before updating to 10.15.4 or you may find your unable to update.
       
       
      Clover EFI Update - 06/04/2020 - Use with Bios revision F12d Only or Replace with the older F11 DSDT if you don't want to update the bios
      Clover Z390 Pro Navi Vega 19,1 EFI 060420.zip - Vega, Navi (5700, 5700XT etc), Radeon VII DSDT EFI
      Clover Z390 Pro Polaris 19,1 EFI 060420.zip - R5xx Polaris DSDT EFI
       
       
      PLEASE NOTE - Please flash your motherboard bios to revision F12d to use my current EFI. It’s a major rework of the bios and vital changes have been made to the layout and power tables. New DSDTs have been created and installed into the new EFI’s but will not work correctly with any other bios revision.
       
       
      Latest Gigabyte Z390 PRO BIOS (F12d)
      mb_bios_z390-aorus-pro_f12d.zip
       
       
      CFG Unlock (MSR) F12d (F12c Pro WIFI) BIOS Profile - The Easy Way 
      Highly recommended if your using a Vega 56/64, Radeon VII or Navi GPU
       
       
      DSDT's (A big thanks to @MaLd0n for compiling these DSDT's)
       
       
      Alternative EFI - OpenCore v0.5.7, No DSDT and Done the way OpenCore intended it (06/04/2020)
       
       
      Alternative EFI 2 - N-D-K OpenCore v0.5.7 (06/04/2020)
       
       
      To Create Your Own Patched DSDT Message @MaLd0n using the link bellow
      https://www.olarila.com/forum/17-dsdt-patch-requests/
      (If you want a perfect setup then getting your own patched DSDT made would be the best thing to do, Mine will work perfectly fine but different hardware no matter how small a change it is can tend to have some sort of effect on the DSDT and your setup)
       
       
      If Your Not Using File Vault Then Please Disable Hibernate
      disablehibernate.command
       
       
      ADDITONAL DOWNLOADS
      Clover
      Clover Configurator
      Kext Updater
       
       
      OPTIONAL DOWNLOADS
      BroadcomFix.zip   (Use these kexts if your Broadcom bluetooth/Wifi isn't working properly)
      FakeSMC    (Can be used instead of VirtualSMC)
      Hackintool
      IORegistryExplorer
      Native Display Brightness with MonitorControl
       
       
      BIOS SETTINGS (Bios Revision F12d)
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • Boot -> Windows 8/10 Features -> Win 8/10WHQL
      • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first)
      • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1
      • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice)
      • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot
      • Settings -> IO Ports -> Internal Graphics -> Enabled (Set to Disabled if using SMBios iMacPro1,1)
      • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M
      • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M
      • Settings -> IO Ports -> Aperture Size -> 256MB
      • Settings -> IO Ports -> Audio Controller -> Enabled
      • Settings -> IO Ports -> Above 4G Decoding -> Enabled
      • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto
      • Settings -> IO Ports -> USB Configuration ->  XHCI Hand-off -> Enabled
      • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled
      • Settings -> Platform Power -> Platform Power Management -> Enabled
      • Settings -> Platform Power -> ErP -> Enabled
      • Settings -> Platform Power -> RC6(Render Standby) -> Enabled
       
      • Save & Exit → Save & Exit Setup 
       
       
      SCREENSHOTS
      
       

       

       

       

       

       

       

       

       

       

    • By AudioGod
      I have put together this simple little guide for anybody wanting to use a Patched DSDT EFI with the same configuration as me.
      This is also a thread to discuss everything Z390 Master and try and help where we can and maybe make things a little better for you. 
       
      A huge massive thank you to @glasgood @MaLd0n @larabee These three guys have helped me and talked me so much and are as helpful as you could ever get, Without them I wouldn't have a perfect working build like I do or be putting up this Guide & Discussion Thread sharing the hard work and countless hours that we have all put in to this.   
       
       
      This EFI and Patched DSDT have been created to work with a Gigabyte Aorus Z390 Master using bios revision F11c, 9900k with a 5700 XT but has also been tested and verified fully working with the following Hardware
       
      CPU's
      8600K, 8700, 8700K, 9600K, 9700K, 9900K, 9900KS
       
      GPU's
      RX 560, 570, 580, 590, Vega 56, Vega 64, Radion VII, 5700, 5700 XT
      (If you have success with any different CPU or GPU's then please do let me know)
       
       
       @glasgood Has kindly put together a new simple Catalina install guide so Just Follow He's Guide For a Perfect Install. (glasgood put the guide together for the Z390 Pro but the two boards are so alike that you can follow this guide with no problems at all using the Z390 Master)
       
       
      HARDWARE USED
      • Intel I9 9900k @5.2Ghz
      • Gigabyte AORUS Z390 MASTER
      • Sapphire Reference RX 5700 XT ( connected to monitor with DisplayPort )
      • Corsair Vengeance Pro RGB 32GB @3600mhz (2 x 16GB)
      • Corsair RM850x 80 Plus Gold Power Supply Unit
      • EK Custom Liquid Cooling Loop
      • Samsung 970 EVO 1TB NVMe SSD macOS Catalina 10.15.3
      • Samsung 860 EVO 1TB SSD (2.5) Windows 10 Pro
      • ABWB BCM943602CS 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E)   
      • Lian Li PC-O11DW Dynamic ATX Case
       

       

       

       
      WORKING
      • Sound 
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 (All ports Open Natively)
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Sleep & Wake
      • Sleep and Shutdown via the Power Button
      • Handoff
      • Netflix on Safari browser
      • Continuity
      • Sidecar (only works using the iMac19,1 EFI and with your igpu Enabled)

       
      EFI FOLDERS  
      please note - You must flash your Z390 MASTER bios to revision F11c to use any of these EFI's, The DSDT is not designed for any other Bios revision
      mb_bios_z390-aorus-master_f11c.zip - Aorus Z390 Master Bios F11c 
       
      Current EFIs 
      Updated 06/04/2020
      PLEASE NOTE - You MUST update to the latest Clover EFI before updating to 10.15.4 or you may find your unable to update.
       
      Clover EFI Updated 06/04/20 - Use with Bios revision F11c Only or Replace with the older F10 DSDT if you don't want to update the bios
      Clover Z390 Master Navi Vega 19,1 EFI 060420.zip - Vega, Navi (5700, 5700XT etc), Radeon VII DSDT EFI
      Clover Z390 Master Polaris 19,1 EFI 060420.zip - R5xx Polaris DSDT EFI
       
       
      CFG Unlock (MSR) F11c BIOS Profile - The Easy Way 
      Highly recommended if your using a Vega 56/64, Radeon VII or Navi GPU
       
       
      ADDITIONAL DSDT's (A big thanks to @MaLd0n for compiling these DSDT's)
       
       
      Alternative EFI - OpenCore v0.5.7, No DSDT and Done the way OpenCore intended it (06/04/2020)
       

      Alternative EFI 2 - N-D-K OpenCore v0.5.7 (06/04/2020)
       
       
      To Create Your Own Patched DSDT Message @MaLd0n using the link bellow
      https://www.olarila.com/forum/17-dsdt-patch-requests/
      (If you want a perfect setup then getting your own patched DSDT made would be the best thing to do, Mine will work perfectly fine but different hardware no matter how small a change it is can tend to have some sort of effect on the DSDT and your setup)
       
       
      If Your Not Using File Vault Then Please Disable Hibernate
      disablehibernate.command
       
       
      ADDITONAL DOWNLOADS
      mb_bios_z390-aorus-master_f10
      Clover
      Clover Configurator
      Kext Updater
      RepairPermissions
       
       
      OPTIONAL DOWNLOADS
      BroadcomFix.zip   (Use these kexts if your Broadcom bluetooth/Wifi isn't working properly)
      Hackintool
      IORegistryExplorer
      Native Display Brightness with MonitorControl
       
       
      BIOS SETTINGS (Bios Revision F11C)
       
      • Enter BIOS → Press Delete → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • Boot -> Windows 8/10 Features -> Win 8/10WHQL
      • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first)
      • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1
      • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice)
      • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot
      • Settings -> IO Ports -> Internal Graphics -> Enabled
      • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M
      • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M
      • Settings -> IO Ports -> Aperture Size -> 256MB
      • Settings -> IO Ports -> Wifi -> Disabled
      • Settings -> IO Ports -> Audio Controller -> Enabled
      • Settings -> IO Ports -> Above 4G Decoding -> Enabled
      • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto
      • Settings -> IO Ports -> USB Configuration -> XHCI Hands-off -> Enabled
      • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled
      • Settings -> Platform Power -> Platform Power Management -> Enabled
      • Settings -> Platform Power -> ErP -> Enabled
      • Settings -> Platform Power -> RC6(Render Standby) -> Enabled
       
      • Save & Exit → Save & Exit Setup
       
       
      SCREENSHOTS

       

       

       

       

       

       

       

       
    • By anokic
      I have been using clover to install and configuration my Hackintosh High Sierra 10.13.6. It's been a struggle and a pain. Can't restart/shutdown/wake from sleep. Random freezes. When freeze happens mouse works but in loading state. UI and open apps freeze not the mouse. I can make the apps smaller and move them.

      I haven't used any DSDT nor SSDT. Tried 5 or 6 of them from others but sometimes i end up not booting. Could someone explain me do i even need them and why? Do i need DSDT or SSDT or both?

      I'm going to try to install everything OpenCore. The first thing is i can't use a method that needs an internet while installing MacOS cause my ethernet/internet only works when i install MacOS. So i can't use the images i need full installation. Okay i have the full installation for 10.13.6. I need to use a version 10.13.4-6 versions cause application Sketch needs the newer one High Sierra 10.13.4++ version.

      Can you tell me? Can i use same kexts from Clover on OpenCore? Secondly how can i install full USB MacOS installer? (High Sierra 10.13.6 version i have is 7gb i think thats it)
      Is there a version of AMDHigh Sierra version made from the community for 10.13.4++ version?
      If i use the normal 10.13.6 High Sierra should i use this AMD 10.13.6 Kernel when i have installed the MacOS or some other kernel that's better for my system? https://github.com/Shaneee/AMD-High-Sierra-XNU/releases
      Whats the best version of High Sierra to use for Ryzen and Nvidia system?

      Will it be better to use OpenCore?

      Specs:
      Mortar Max B450M
      Ryzen 2600x
      Nvidia GTX 1060
      16gb DDR4 2400mhz
×