Jump to content
joshhh

[GUIDE] Lenovo ThinkPad T510/510i (plus T410 and W510) 10.6-10.7-10.8-10.9 all working OK! 2013.11.12 Update

499 posts in this topic

Recommended Posts

I'll upload updated bioses today when back to home and try to check your dumps too. To much deadlines on job in this month

 

(mostly) cool and monitor preferences are bound to Alt/Opt + ScrLk :-)

 

Decreasing the brightness with ScrLk works, while increasing with Pause does not, any idea?

 

You already has been able to build a current (1.44) BIOS for the T410 with disabled whitelist for Wifi and WAN?

 

And finally, did you found some time to look into the logs I attached in post #209 to eventually give me a hint how to get working the sound with speakers?

 

 

Thanks a lot for your brilliant work,

 

Yeah. Default clover installation is little bit slower than Chameleon because of its nature. Clover creates real EFI enviroment for OSX, chameleon just leave some tables and signs that EFI was loaded successfully and then boot OSX thats why it much faster...

 

And good news about clover and slow resolution modes. Currently I'm able to use higher than 1024*768 boot screen resolution, in my case its 1920*1200 for external display. Didn't have time to test it with common resolutions like 1366*768/1600*900/1920*1080 (maybe some different ones too) for Lenovo screens.

 

Hope to release cClover config update this weekend

 

Installed Clover today. Everything's fine, but it's loading much longer, than Chameleon (I mean bootloader itself, not OSX). Is this OK or i did something wrong? =)

Share this post


Link to post
Share on other sites
Advertisement

Brightness controls is binded to ScrLk/Pause by VoodooPS2. Its impossible to bind Fn+Home/End to do this because this combo doesn't generate any key codes and talk with bios WMI features only available from Windows, so we can't use it at all...

 

About speedstep and boost - see in boot log text like AppleIntelCPUPowerManagement success and Turbo Ratios 0035. First one is for speedster, second is for boost. OSX doesn't show boots ratios in monitoring software.

 

Thanks, sadly ScrLk/Pause doesnt work for me either, but the applications "ScreenDimmer" and "Shades" (shades only sometimes). They dont look like they adjust the brightness the same way though.

 

As far as the boot log text, i didnt know where to look. But i went into the system log queries and found the following (relevant) entries:

 

 

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagement: Turbo Ratios 1169

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagement: (built 00:59:42 Aug 25 2012) initialization complete

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelE1000e(Info): changing MTU from 0 to 1500

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagementClient: ready

 

Also maybe something of note, i have sound assertion crapping all over the log file, like this:

 

11/29/12 12:08:08.000 AM kernel[0]: Sound assertion in AppleHDAWidget at line 3095

Share this post


Link to post
Share on other sites

Yeah. Default clover installation is little bit slower than Chameleon because of its nature. Clover creates real EFI enviroment for OSX, chameleon just leave some tables and signs that EFI was loaded successfully and then boot OSX thats why it much faster...

Can't say "little bit", but much slower =) I have UEFI motherboard at home, so don't you know if it faster on UEFI MoBos?

And good news about clover and slow resolution modes. Currently I'm able to use higher than 1024*768 boot screen resolution, in my case its 1920*1200 for external display. Didn't have time to test it with common resolutions like 1366*768/1600*900/1920*1080 (maybe some different ones too) for Lenovo screens.

 

Hope to release cClover config update this weekend

OK, we're waiting =) Thanx

Share this post


Link to post
Share on other sites

Speedstep and boots works in your case

 

About brightness... easiest way to check it go to system preferences - displays and see if brightness slider exist. If not - keys will not control it.

 

Screen brightness depends on two things in Lenovos

 

PNLF device in dsdt

 

and strings in PCI0-PEG-VID devices in section DSM

 

"AAPL,backlight-control",
						    Buffer (0x04)
						    {
							    0x01, 0x00, 0x00, 0x00
						    },
						    "@0,backlight-control",
						    Buffer (0x04)
						    {
							    0x01, 0x00, 0x00, 0x00
						    },

 

 

 

Thanks, sadly ScrLk/Pause doesnt work for me either, but the applications "ScreenDimmer" and "Shades" (shades only sometimes). They dont look like they adjust the brightness the same way though.

 

As far as the boot log text, i didnt know where to look. But i went into the system log queries and found the following (relevant) entries:

 

 

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagement: Turbo Ratios 1169

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagement: (built 00:59:42 Aug 25 2012) initialization complete

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelE1000e(Info): changing MTU from 0 to 1500

11/28/12 11:36:05.000 PM kernel[0]: AppleIntelCPUPowerManagementClient: ready

 

Also maybe something of note, i have sound assertion crapping all over the log file, like this:

 

11/29/12 12:08:08.000 AM kernel[0]: Sound assertion in AppleHDAWidget at line 3095

 

On UEFI motherboards its much faster cause it doesn't use some emulation layer stuff to make some dummy EFI for OSX

 

And also there is silent boot option available for clover when it boot osx without entering GUI

 

Can't say "little bit", but much slower =) I have UEFI motherboard at home, so don't you know if it faster on UEFI MoBos?

 

OK, we're waiting =) Thanx

Share this post


Link to post
Share on other sites

On UEFI motherboards its much faster cause it doesn't use some emulation layer stuff to make some dummy EFI for OSX

 

And also there is silent boot option available for clover when it boot osx without entering GUI

heh, i'll try to install it =)

It will be tricky, i think, not to ruin everything =)

Share this post


Link to post
Share on other sites

Thanks,

 

I see the following sections in the DSDT i am using. Are these entries correct for my W510 with nvidia 880m (1GB)?

 

 

Device (PNLF)

{

Name (_HID, EisaId ("APP0002"))

Name (_CID, "backlight")

Name (_UID, 0x0A)

Name (_STA, 0x0B)

}

 

 

Method (_DSM, 4, NotSerialized)

{

Store (Package (0x06)

{

"AAPL,backlight-control",

Buffer (0x04)

{

0x01, 0x00, 0x00, 0x00

},

"@0,backlight-control",

Buffer (0x04)

{

0x01, 0x00, 0x00, 0x00

},

"@0,pwm-info",

Buffer (0x14)

{

/* 0000 */ 0x01, 0x14, 0x00, 0x64, 0xA8, 0x61, 0x00, 0x00,

/* 0008 */ 0x1C, 0x02, 0x00, 0x00, 0x64, 0x00, 0x00, 0x00,

/* 0010 */ 0x00, 0x04, 0x00, 0x00

}

}, Local0)

DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))

Return (Local0)

}

Share this post


Link to post
Share on other sites

Yes, this should be enough for brightness. And you got slider in display prefs?

 

Could you post your ioregestry explorer dump here?

 

Thanks,

 

I see the following sections in the DSDT i am using. Are these entries correct for my W510 with nvidia 880m (1GB)?

 

Share this post


Link to post
Share on other sites

Yes, this should be enough for brightness. And you got slider in display prefs?

 

No unfortunately i have never seen the slider in display prefs.

 

I am using clover boot loader and I have that DSDT.aml in /EFI/ACPI/PATCHED/ as well as /Extra

 

Is there anyway i can verify that is the DSDT.aml that is being used? When i tried using different ones, i just renamed them to something like DSDT1.aml and iput them in the /EFI/ACPI/PATCHED folder. Then in the boot options of clover, i changed the name of the DSDT.aml, it was only for that boot as the name setting wouldnt persist through reboot. It always affected boot = crashed, or didnt work, so it seemed like my setting change was being used.

 

That seemed the best way to try different dsdt files without hosing the boot.

 

That said, assuming that is the DSDT being used, i am unsure why i dont see the slider.

Share this post


Link to post
Share on other sites

No slider -> wrong dsdt used in boot loader. You need proper config for clover to get GPU working well with brightness settings

 

No unfortunately i have never seen the slider in display prefs.

 

I am using clover boot loader and I have that DSDT.aml in /EFI/ACPI/PATCHED/ as well as /Extra

 

Is there anyway i can verify that is the DSDT.aml that is being used? When i tried using different ones, i just renamed them to something like DSDT1.aml and iput them in the /EFI/ACPI/PATCHED folder. Then in the boot options of clover, i changed the name of the DSDT.aml, it was only for that boot as the name setting wouldnt persist through reboot. It always affected boot = crashed, or didnt work, so it seemed like my setting change was being used.

 

That seemed the best way to try different dsdt files without hosing the boot.

 

That said, assuming that is the DSDT being used, i am unsure why i dont see the slider.

Share this post


Link to post
Share on other sites

Test this AppleHDA, changed some nodes configs in it. Possible it should help. If not I can try to change one more thing

 

And finally, did you found some time to look into the logs I attached in post #209 to eventually give me a hint how to get working the sound with speakers?

 

 

MiniDock Series 3 audio outputs...

 

Dealing with t410 had I possible figure out what two additional audio ports listed in linux dump

 

post-120553-0-25891900-1354203631_thumb.png

 

This two ports is located on Lenovo mini Dock 3 or soooo... I think its possible to get it working well with auto detection disabled for output but cant test it without proper hardware

 

 

Clover boot resolution patch

 

works fine with 1920*1080, i'll test 1600*900 and 1366*768 tomorrow

 

post-120553-0-94845300-1354211018_thumb.jpeg

 

post-120553-0-89351900-1354211024_thumb.jpeg

T410-autodetect-fix-AppleHDA.kext.zip

Share this post


Link to post
Share on other sites

As it turned out, my MB cannot boot from EFI partition of GPT-formatted drives. Only from EFI partition of MBR or hybrid. Maybe it fixed on new "BIOS" versions, but i don't want to update because of hackintosh boot problems (as people say on this forum).

So, i stay on Chimera =)

Share this post


Link to post
Share on other sites

Hi joshhh,

 

thanks a lot for the answer.

 

Test this AppleHDA, changed some nodes configs in it. Possible it should help. If not I can try to change one more thing

Unfortunately it doesn't work, with this AppleHDA I don't get any audio at all (volume is grayed out).

 

 

I figured out, that the "AppleHDA.kext/Contents/MacOS/AppleHDA" are quite different, the mostly working version is "1636848 12 Jul 23:21" while the not working version you attached says "830120 20 Aug 02:11".

 

The version.plist seems to be the same:

 

BuildVersion: 7

CFBundleVersion: 2.3.1f2

SourceVersion: 231004002000000

 

Any Idea? And is there s.th. I can modify by my self to get it working?

Share this post


Link to post
Share on other sites

ohh its Lion version=) check it tomorrow with same changes as for ML ands attach it

 

Hi joshhh,

 

thanks a lot for the answer.

 

Unfortunately it doesn't work, with this AppleHDA I don't get any audio at all (volume is grayed out).

 

 

I figured out, that the "AppleHDA.kext/Contents/MacOS/AppleHDA" are quite different, the mostly working version is "1636848 12 Jul 23:21" while the not working version you attached says "830120 20 Aug 02:11".

 

The version.plist seems to be the same:

 

BuildVersion: 7

CFBundleVersion: 2.3.1f2

SourceVersion: 231004002000000

 

Any Idea? And is there s.th. I can modify by my self to get it working?

 

Before asking it thread. Please fill data about your hardware and software. Without it I can't help

Share this post


Link to post
Share on other sites

Hi joshhh,

 

thank you very much for your patience.

 

ohh its Lion version=) check it tomorrow with same changes as for ML ands attach it
well, I have 10.7.5 installed I think this is Lion?

 

And the AppleHDA that is working with headphones comes from the Lion-directory in your "T410-files" available in the first post.

 

 

A quick look in the zip-files tells me that I'm using the correct version and that you probably attached the ML version (not too bad, because if a ML USB-Install-stick will be available, I will buy it and perhaps will upgrade to 10.8):

 

 

$ ll OSX\ 10.6\ Snow\ Leopard/System-Library-Extensions/AppleHDA.kext/Contents/MacOS/

2074024 3 Sep 20:37 AppleHDA

 

$ ll OSX\ 10.7\ Lion/System-Library-Extensions/AppleHDA.kext/Contents/MacOS/

1636848 12 Jul 23:21 AppleHDA

 

$ ll OSX\ 10.8\ Mountain\ Lion/System-Library-Extensions/AppleHDA.kext/Contents/MacOS/

830120 25 Aug 00:28 AppleHDA

 

 

 

PS: Sorry for the inconvenience, I thought that you still had "in memory" about which system I was speaking. In future I just will add:

"I've installed Lion on my T410 i7 with NVidia/256 and it works mostly perfect. Lion is 10.7.5 and BIOS is updated to the latest original-lenovo 1.44."

Share this post


Link to post
Share on other sites

Hi all,

 

I'm probably wrong but is the battery indicator meant to be working? (I asked before sorry)

Everything else seems ok.

 

(I know built-in wifi doesn't)

 

Also I am thinking of using eSata cable for additional drive, will I have issues (will need to buy enclosure) ?

 

Thanks!

 

(T510 on 10.8.2 LM)

Share this post


Link to post
Share on other sites
I'm probably wrong but is the battery indicator meant to be working? (I asked before sorry) Everything else seems ok.

...

Also I am thinking of using eSata cable for additional drive, will I have issues (will need to buy enclosure) ?

in the very first post it says that both should work OOB. And for my T410 with 10.7.5 I can confirm that.

 

On the other hand, sound also should work, but it does not work for me. So if you do not have the exact same machine with same BIOS and same OS, your results may differ, but anyway I would recheck the installation again.

Share this post


Link to post
Share on other sites
And is there s.th. I can modify by my self to get it working?
no, it seems that I can't :-(

 

I was looking in the differences of the two patched AppleHDA's for 10.8, I found out that the MacOS/AppleHDA-binaries are different and that Joshhh changed two "NodeIDs" in the compressed Resources/Platforms.xml.

 

But I have no clue what was patched in the MacOS/AppleHDA and in addition there is no Resources/Platforms.xml.zlib in the 10.7 kext that could be changed.

 

I even was not able to determine, from where Joshhh got the information about the pin-layout for input-/output channels.

 

So I just have to wait (or always attach headphones/speakers) : -)

Share this post


Link to post
Share on other sites

Battery indication works great with VoodooBattery and eSata works great too but eSata port in OSX doesn't work well with hot-plug. If OSX booted and you connect esata drive it gets detected, but if you unmount in and change physical disk in esata dock OSX won't show it until reboot

 

Hi all,

 

I'm probably wrong but is the battery indicator meant to be working? (I asked before sorry)

Everything else seems ok.

 

(I know built-in wifi doesn't)

 

Also I am thinking of using eSata cable for additional drive, will I have issues (will need to buy enclosure) ?

 

Thanks!

 

(T510 on 10.8.2 LM)

 

 

Here is "fixed" AppleHDA for Lion. If it won't help I can try to 1) unpair speakers-headphones in sound config - easy fix 2) try to change something else in config - needs deeper analysis

 

T410-Lion-fix-AppleHDA.kext.zip

 

 

no, it seems that I can't :-(

 

I was looking in the differences of the two patched AppleHDA's for 10.8, I found out that the MacOS/AppleHDA-binaries are different and that Joshhh changed two "NodeIDs" in the compressed Resources/Platforms.xml.

 

But I have no clue what was patched in the MacOS/AppleHDA and in addition there is no Resources/Platforms.xml.zlib in the 10.7 kext that could be changed.

 

I even was not able to determine, from where Joshhh got the information about the pin-layout for input-/output channels.

 

So I just have to wait (or always attach headphones/speakers) : -)

Share this post


Link to post
Share on other sites

Hi joshhh,

 

Here is "fixed" AppleHDA for Lion.
thank you very much for this.

 

If it won't help I can try to 1) unpair speakers-headphones in sound config - easy fix 2) try to change something else in config - needs deeper analysis
I've seen that you added a "Platforms.xml" to the resources-directory, unfortunately it does not change anything either.

 

 

What do you mean with "unpair speakers-headphones in sound config" and how is it done?

 

If I go to the Audio-Preferences, I see on the "Output"-tab, that I have "Name: Internal Speakers, Typ: Integriert" (funny it's mixed German and English language), if I plug in my headphones, it changes to "Name: Headphones, Typ: Integriert" and the audio is played.

 

On the "Input"-tab I have "Line In" (not tested) and "Internal microphone" which is working if I select it.

 

 

On my old T60 with SL I had running the VoodooHDA, but I had several problems with it, like KPs and non-working audio after resume, so I do not want to try this again.

 

Does it make any difference that I am using the latest 1.44 BIOS on my T410, would it make sense to downgrade to your patched 1.43-version?

 

Is there a way to get audio working without patching the AppleHDA and just changing the DSDT for the laptop?

 

 

PS: "I've installed Lion on my T410 i7 with NVidia/256 and it works mostly perfect. Lion is 10.7.5 and BIOS is updated to the latest original-lenovo 1.44."

Share this post


Link to post
Share on other sites

First off, thanks for all the hard work Joshhh. ML works well on my T510.

 

Could anyone confirm that HDMI functions correctly? Because I can get the video output works but not for audio output.

In the system->sound->output panel, there is only internal speakers found.

Thanks

Share this post


Link to post
Share on other sites

Unpair will make two devices in outputs headphones and speakers

 

T410-Lion-fix-2-AppleHDA.kext.zip

 

 

 

 

DP->HDMI for video works well but for audio I got some problems with freeze on system boot and there is no TV listed in output options. Anyway I dint have much time to test all vars so possible it may work for audio output

 

First off, thanks for all the hard work Joshhh. ML works well on my T510.

 

Could anyone confirm that HDMI functions correctly? Because I can get the video output works but not for audio output.

In the system->sound->output panel, there is only internal speakers found.

Thanks

Share this post


Link to post
Share on other sites

My T410 (2522-CTO) has some problem after update to 10.8.2. I've follow this post:

 

Install Update and rollback AppleACPIPlatform and AppleHDA before reboot

 

And this thread (Step 4):

http://lifehacker.co...ng-a-hackintosh

 

Now it works well as 10.8. Many thanks to Joshhn, you've bring Mac OS X to my Lap :) )

Share this post


Link to post
Share on other sites

My Lap loss audio & hangs on the gray Apple screen during boot. It still can boot into Graphic Safe mode (Using -x option at Chimera boot loader menu)

:)

 

What kind of problem did you get?

Share this post


Link to post
Share on other sites
Unpair will make two devices in outputs headphones and speakers
still no luck :-(

 

Headphones and Internal Speakers now are seperated in the Audio-prefs, if I select "Headphones" I get sound through them, if I select "Internal Speakers" I get nothing anymore.

 

What about others on their T410, do they get audio through the internal speakers?

 

 

PS: "I've installed Lion on my T410 i7 with NVidia/256 and it works mostly perfect. Lion is 10.7.5 and BIOS is updated to the latest original-lenovo 1.44."

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By MaLd0n
      -Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      -Donations with Bitcoin
      33HeGCuCSh4tUBqdYkQqKpSDa1E7WeAJQ3
       
      -Donations with PicPay 
      @danielnmaldonado
       
      -Donation with Mercado Livre 
      https://tinyurl.com/y9evkj5u
       
       
      --Original Topic--
      https://www.olarila.com/topic/6874-olarila-hackbook-lenovo-ideapad-s145-mojave-catalina-full-dsdt-patches/
       

       
      -Perfect HackBook, HDMI Audio/Video, Bluetooth, AirPlay, Sleep, Lid Sleep, Auto Sleep, Audio, etc!
      -Wifi card has been replaced with Dell DW1560!
      -I'm using a S145-15IWL Model with Intel Core i5 8265u / Intel UHD Graphics 620
      -Update bios/uefi to last version
       
      --Installation--
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
       
      --Clover Folder--
      https://tinyurl.com/rkqmpd9
       
      --OpenCore Folder--
      https://tinyurl.com/y75hqg7z
       
      Bluetooth Broadcom
      Bluetooth Broadcom.zip
       
      CPUFriend for i5-8265U
      CPUFriend i5-8265U.zip
       
      --Full DSDT Patches--
      -My DSDT
      DSDT Lenovo IdeaPad S145.zip
       
      This DSDT work on S145-14IWL, S145-15IWL, V14-IWL, V15-IWL models
      -Patches
      -FIX ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 11 ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PRWs -_DSMs -PNLF -BRIGHTNESS KEYS -I2C -NATIVE USB -ARPT -GFX0 -DTGP -kUSBCompanionIndex -io-device-location -FULL RENAMED DEVICES   --IGPU Patch--
      Video solution with HDMI Audio and Video
      <key>PciRoot(0x0)/Pci(0x2,0x0)</key> <dict> <key>AAPL,GfxYTile</key> <data> AQAAAA== </data> <key>AAPL,ig-platform-id</key> <data> CQClPg== </data> <key>device-id</key> <data> pT4AAA== </data> <key>enable-hdmi20</key> <data> AQAAAA== </data> <key>framebuffer-con0-alldata</key> <data> AAAIAAIAAACYAAAA </data> <key>framebuffer-con0-enable</key> <integer>1</integer> <key>framebuffer-con1-alldata</key> <data> AQEJAAAIAADHAQAA </data> <key>framebuffer-con1-enable</key> <integer>1</integer> <key>framebuffer-con2-alldata</key> <data> AgYKAAAEAADHAQAA </data> <key>framebuffer-con2-enable</key> <integer>1</integer> <key>framebuffer-fbmem</key> <data> AACQAA== </data> <key>framebuffer-patch-enable</key> <data> AQAAAA== </data> <key>framebuffer-stolenmem</key> <data> AAAwAQ== </data> <key>framebuffer-unifiedmem</key> <data> AAAAgA== </data> <key>hda-gfx</key> <string>onboard-1</string> <key>model</key> <string>Intel Corporation, Iris Plus Graphics 655</string> </dict>   --Native USB Fix for Notebooks - No Injector/Kext Required--
      https://www.olarila.com/topic/6878-guide-native-usb-fix-for-notebooks-no-injectorkext-required/
      https://www.olarila.com/topic/6181-guide-native-usb-fix-for-desktops-no-injectorkext-required-skylake/
       
       
      -ScreenShots

































      -Links
       
       
      Clover https://github.com/CloverHackyColor/CloverBootloader
      AirportBrcmFixup.kext https://github.com/acidanthera/AirportBrcmFixup
      AppleALC.kext https://github.com/acidanthera/AppleALC
      Brcm Bluetooth https://github.com/acidanthera/BrcmPatchRAM
      Lilu.kext https://github.com/acidanthera/Lilu
      SystemProfilerMemoryFixup.kext https://github.com/Goldfish64/SystemProfilerMemoryFixup
      VirtualSMC.kext https://github.com/acidanthera/VirtualSMC
      VoodooI2C.kext https://github.com/alexandred/VoodooI2C
      VoodooPS2Controller.kext https://github.com/acidanthera/VoodooPS2
      WhateverGreen.kext https://github.com/acidanthera/WhateverGreen
      MaciASL - https://github.com/acidanthera/MaciASL
      acpica - https://github.com/acpica/acpica
      AptioMemoryFix.efi https://github.com/acidanthera/AptioFixPkg
      ApfsDriverLoader.efi https://github.com/acidanthera/AppleSupportPkg
      HFSPlus.efi https://github.com/JrCs/CloverGrowerPro/blob/master/Files/HFSPlus/X64/HFSPlus.efi?raw=true
      Hackintool https://github.com/headkaze/Hackintool
       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
       
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
       
      We're all here to have fun and learn from each other!
    • By BigAl
      i am getting a new lenovo ideapad 3 ( 15ADA05)
       
      1920 x 1080 - Ryzen 3 3250U - 8 GB RAM - 256 GB SSD - Windows 10 Home 64-bit - AMD Radeon Graphics - Twisted nematic (TN) - English Keyboard - 0.3 Megapixel Front Camera - Bluetooth
       
      I would love to know if its possible to put mojave  on it. i am a noob  so currently still learning and trying to gain as much info as i can.
       
      If anyone could tell me if its possible and point me in the direction that would be great
       
      Thanks in advance
      Al
    • By Isptn
      Hi I am newbie to Mac development and currently trying to get info whether a display is captured, I found such info in doc: CGDisplayIsCaptured(_:).
      https://developer.apple.com/documentation/coregraphics/1562061-cgdisplayiscaptured.
      But this one is deprecated. How can I find out whether a display is captured in other way?
      The goal is: The app should be visible only for user not for those, who see shared screen. So II need to blur the app on screen capture or send notification to user that screen is currently capturing, so I need to know which event cold notify me about that.
    • By MSzturc
      Hello everyone!
       
      I know that a lot of you are using a Lenovo Thinkpad as Hackintosh. For those i've created an Assistant Application that allows you to use all your Function Keys on your Laptop. It should be compatible to all T-, R-, X- and E-Series Models with the right Keyboard mapping.
       
      Features
      Fn+F4: Mute / Unmute Microphone Fn+F7: Screen mirroring / Screen extending Fn+F8: Activate / Deactivate Wi-Fi Fn+F9: Open System Preferences Fn+F12: Open Launchpad  
      Demo
       
       
      Keymapping
       
       
      Download & Changelog
      GitHub
       
    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub (March 2020) Updated to Clover r5105 Updated Lilu based kexts - Lilu, ALC, WEG Added AirportBrcmFixup.kext
        Various Tweaks over Last months The main branch in my github repo is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle seems to work on Sierra, HighSierra, Mojave and Catalina. There is an OpenCore branch in the repo as an alternative to Clover. This guide was developed for a Clover implementation. But the thread has evolved to include discussion of both Clover and Opencore for these systems: T460 and T470 family of ThinkPads.
       
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (the old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
×