Jump to content
Welcome to InsanelyMac Forum

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

  • Announcements

    • Allan

      Forum Rules   04/13/2018

      Hello folks! As some things are being fixed, we'll keep you updated. Per hour the Forum Rules don't have a dedicated "Tab", so here is the place that we have our Rules back. New Users Lounge > [READ] - InsanelyMac Forum Rules - The InsanelyMac Staff Team. 
novaris

Mac Mini media player case mod.

1 post in this topic

Recommended Posts

Well, strictly speaking this is my 4th case mod but this is simple enough for me to post a worklog about it. the other case mods are powermac g5, powermac g4 cube and mac pro(work in progress)

 

Bought the mac mini from ebay and it didn't arrive in a very good condition as described. front side had some noticeable scratches and the top white acrylic panel had alot of fine scratches. Either way, it remained in my cupboard for sometime, just too small for mini-itx and i did attempt to make it into an iphone dock but didnt materialise.

 

Anyway, i chanced on some good offers for compact media players for just about ~US$100-110

 

AC ryan HD2 mini

http://www.hardwareh...inside-full.jpg

 

asus o play Mini

http://prohardver.hu..._mini_pcb_b.jpg

 

Western Digital tv live

http://www.storagere...-Live-Apart.jpg

 

Eventually i chose the WD tv live since, the asus media player didnt have ethernet port and the sale staff was too lazy to give proper answers and the ac ryan circuit board might be just too big for the mac mini. plus, the WD sales staff were well prepared and didn't mind giving a full introduction to the device's interface.

 

dismantling the media player

 

40ce07f4.jpg

 

there goes the warranty

90567e67.jpg

 

 

Since the media player's circuit board is too short, i had 2 options

 

either i place it nearer to the front to connect the power led directly and cut a small hole for the IR receiver and make short male-female extensions for the rear HDMI, power ports, etc so that it can reach the back

 

or

 

I place it nearer to the back so the hdmi ports etc, can be directly accessed without any extensions. but i have to solder some extension wires for the front led and IR receiver.

 

Decided to do the latter, just soldering 5 wires but meant that warranty is 100000% voided and I better get it right.

659a3b1e.jpg

 

soldering point of the power led and IR receiver. solder points look quite dull, sub-optimal soldering?

 

ac0fdf79.jpg

 

the mac mini board has quite a few of little plastic "bumps" so placing the circuit board or anything will not result in a level surface.

 

Decided to use a 5mm thick junk acrylic to raise the circuit board and use double sided tape to hold it in place because if the media player spoilts or something else better comes in, I can easily replace it.

 

 

Instead of reusing the media player's led i decided to use the mac mini's onboard power led instead but its wires are too short so soldering them require some deft handiwork. :o something i am not famous for.

 

 

Picture.jpg

 

Had some complications when I wanted to solder the extension wires for the led and Ir receiver.

 

~~the wires I used were made of twisted thin copper wires so it was harder to solder properly than single core wires.

 

~~the soldering iron's tip was quite worn out

 

~~had to get soldering clamp to hold the wires and circuit board because soldering and holding wires in place was just too difficult.

 

~~while the pinout for the led on the media player's circuit board was labelled clearly, the mac mini's led wasn't

 

 

 

 

End result...

 

 

792ad1a8.jpg

 

mac mini's led powered by the media player. Hope they run on the same voltage.

 

Later on, i'll test whether the IR receiver works well. Hope I didnt damage it with heat from the soldering iron....

 

 

 

 

 

next step is to see whether i can find a slot loading usb powered dvd drive that can fit inside the case without protruding....

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Recently Browsing   0 members

    No registered users viewing this page.



×