Jump to content

[Risolto] Wifi e penna wifi RTL8187L non funzionanti


iakughan
 Share

8 posts in this topic

Recommended Posts

Salve, sono riuscito ad installare (finalmente) lo snow leopard sul mio pc in firma. Ho solo alcuni problemi:

 

1) Non mi funziona la scheda di rete, il mio pc è dotato di una atheros ar5007eg, ho provato ad installare dei fix per le atheros ma senza risultato.

Allora ho provato ad inserire una penna wifi tramite usb, questa è dotata di chip realtek 8187, ho installato dei pacchetti e dei kext per questo modelo. Se vado in impostazioni/network mi da una casella con scritto realtek 8187, ma appena inserisco la penna wifi il pc non la rileva. Come posso risolvere? C'è qualche modo per abilitare la scheda di rete interna o qualche kext in particolare per la mia penna wifi?

 

2) Non mi funziona lo sleep, ho provato con kext vari o con pacchetti del tipo di smartsleep ma niente. Come risolvo?

 

3) Diciamo che è il problema minore; ho alcuni lag piccolissimi di scattosità nel puntatore del mouse, diciamo che non è fluidissimo, penso sia dovuto al kext video, è RadeonHD 3200, non supporta QE/CI. C'è un kext alternativo che sia migliore? la mia scheda video è in firma.

 

Grazie

 

EDIT:

 

Ho risolto seguendo questa semplice guida:

 

1) Download the Realtek RTL8187L from this link: http://www.4shared.com/file/pydSlS39/036_M...57.html?cau2=...

If you download from another link, be sure you are downloading 8187L, NOT 8187B. 8187B will not work in this case.

 

2) Unpack the RAR file using a program such as Zipeg (my personal favorite unarchiving tool for Macs - Google it for a download link). Once unpacked, double-click the install.pkg file to begin the installation, and proceed through the installation as you normally would. Restart your computer.

 

3) Once rebooted, open up a Terminal window. Then type in the commands listed below in that order (leave out the #, they are simply indicators of commands). When using sudo you will be prompted for your password, so be prepared to enter it.

# cd /System/Library/Extensions

# sudo chmod -R 755 rtl8187l.kext

# sudo chown -R 0:0 rtl8187l.kext

# exit

Close the Terminal window and once again reboot your computer.

 

4) Plug in your device via the USB connector. Then open up Terminal once more and type:

# sudo kextutil -t -v /System/Library/Extensions/rtl8187l.kext

# exit

Close Terminal.

 

5) At this point the Mac Network window will open and you if you want to accept a new interface. DO NOT TOUCH ANY SETTINGS JUST YET, just accept it. Realtek should then open and assign an IP address to your Alfa device.

 

 

That's it! You're done. To connect to a wireless network, plug in your Alfa device and open up the Realtek application. Go over to the "Available Network" tab and choose the network you want, then click connect. Input the password if necessary. And your connected! You can shutdown the Apple AirPort service if you so choose and make your Alfa device your primary wireless interface.

 

 

TROUBLESHOOTING:

 

- Check to make sure the chipset is rtl8187l, NOT rtl8187b, as this chipset requires a different driver and is not covered in this guide (though the same basic steps should in fact work).

 

- In Terminal, type:

# sudo rm /System/Library/Extensions.mktext

This will reset all of the kept caching done by OS X. Reboot your computer.

 

- Ask in the comments. I will see what I can do.

Link to comment
Share on other sites

Piccolo aggiornamento: La mia penna wifi è una realtek RTL8187L (non 8187B), ho visto che nel sito ufficiale c'è il driver fino a leopard, ho provato ad installarlo ma mi da kernel panic, ho avviato con -v, tutto si avvia ma mi dice che il pacchetto non è stato installato correttamente. Esiste un kext modificato che supporti snow leopard per RTL8187L?

Link to comment
Share on other sites

Ho installato un pacchetto e adesso mi riconosce una porta ethernet in eh0. solo che questa porta mi viene segnalata come autoassegnata e non riesco a connettermi ancora. C'è qualche driver per RTL8187L??

Link to comment
Share on other sites

non funzionano, ho provato con arch=i386 ma nulla, tra l'altro dopo che li intallo non mi fa aprire nemmeno il realtek utility. Altre soluzioni?

Link to comment
Share on other sites

  • 3 months later...
 Share

×
×
  • Create New...