Unfortunately, removing the THB cable isn't working with the ASRock MB, no TB devices show up at all...
When I had the gigabyte Gaming 7 Pro and was waiting for the connector adapter (GB uses a different header pitch: 2mm vs 2.54mm) no TB devices were seen in macos either...
Ok so I was having issues with on-board and HDMI audio using VoodooHDA. No AppleALC due to AMD setup. VoodooHDA was crackling on on-board and couldn't sort and there was no HDMI output. So I bought a Sabarent AU-MMSA USB Audio device. Issue is it's acting just like the on-board audio was. With or without VoodooHDA being injected.
This is my first hackintosh Build. I installed windows 10 and made sure everything was working then i Change my bios settings. (See Below) I Created a ##### usb with latest version of high Sierra 10.13.4 then installed it after erasing the whole drive Booted into MacOS then ran [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] with these settings below then that when i Get the black screen after clover boot screen then i have to turn off the monitor and turn it back on to get a picture on one of my monitors.. I have 2
Ethernet is working
MOTHERBOARD GIGABYTE Z370 AORUS Gaming 5
CPU Intel Core i7-8700K Desktop Processor 6 Cores up to 4.7GHz Turbo Unlocked LGA1151 300 Series 95W BX80684i78700K Graphics Card Gigabyte AORUS Radeon RX 580 8G 8GB GDDR5 256bit Graphics Card GV-RX580AORUS-8GD Cooling NZXT Kraken X62 All-in-One 280mm CPU Liquid Cooling System Ssd Hardrive Crucial MX300 1TB 3D NAND SATA M.2 (2280) Internal SSD Memory G.SKILL TridentZ RGB Series 16GB (2 x 8GB) 288-Pin DDR4 3000MHz (PC4 24000) CASE Nzxt S340VR Elite Computer Case Bluetooth / WIFi (removed onboaard wifi and put this card) Broadcom BCM94352Z M.2 NGFF 802.11AC 867Mbps BT 4.0 DW1560 for Mac Hackintosh Power supply EVGA SuperNOVA 650 G3 650W 80 Plus Gold Modular Power Supply
Quick Start - UEFI Boot Mode
FakeSMC HWMonitor Application
Network - Intel - Choose latest IntelMausiEthernet
USB - Increase Max Port Limit 200 Series
Bootloaders - Clover v2.4k r4063 UEFI Boot Mode + Emulated NVRAM
Graphics Configuration - AMD Graphics Fixup (required for AMD card!)
System Definitions > iMac - iMac18,3
After POST beep, press/hold DEL key to enter UEFI/BIOS
Save & Exit menu - choose Load Optimized Defaults.
MIT > Advanced Frequency Settings > Extreme Memory Profile (X.M.P) - choose Profile 1
Full Screen LOGO Show - I disable this, but not really required
Boot Option Priorities - set this to the UEFI option for your UB flash drive. Disable all other choices. Once we run #####, we’ll come back in here and set to your new boot drive (in my case, the UEFI partition of Samsung 960PRO).
CSM Support - Disable. Note that the Storage Boot Option Control option which is set to UEFI (desired setting) disappears along with the other 3 options under CSM Support when you set to Disable. Don’t worry, as Storage Boot Option Control apparently stays set to UEFI “under the hood.”
Initial Display Output - mobo should auto-detect your GPU card, so this should already show PCIe 1 Slot. You shouldn’t have to do installation using internal GPU, then switch to your GPU card.
Peripherals > LEDs in sleep, Hibernation, and Soft Off States: OFF [this is optional if you don't want LEDs on 24/7, even in power-off state).
USB Configuration > XHCI Hand-off - set to Enable
Note: Once Thunderbolt3 AIC is connected, a new dynamic menu option for configuring the Alpine Ridge card appears below the USB DAC option (which lets you set options for USB charging on the appropriate ports).
VT-D - Disabled
Internal Graphics - Disabled (this also turns off the DVMT menu options).
Wake on LAN Enable - Disable
ErP - Enabled [UPDATE 25Mar2018] - This is now required to help fix issue where mobo on-board LEDs do not power off when in sleep/shutdown mode.
Soft-Off by PWR-BTTN - I set this to Delay 4 Sec.
Save & Exit - Choose Save & Exit Setup - this saves your changes and reboots your system.