Acer Aspire 5735z Install Iatkos s3 v2 Help

[camzgon]

Hi guys, I've been at this for about 2 days. I tried using the retail edition of snow leopard, then I moved onto iatkos. Anyway,

 

Install process was a hit and miss, sometimes it would load (take 5 minutes) if I used the above options, sometimes install wouldn't load at all (even if I used those options or nothing at all), If I used no options, it would stay on the grey screen with no animations. If I did the options it would take a while before going to the install screen. And even then, sometimes the touchpad would be unresponsive.

 

I left the kernel on default, installed the drivers for the ethernet, wireless and left the VGA unchecked. AFter installation finished and rebooted, I first tried booting with any options, it wouldn't boot. I then tried it with the above flags that I used when trying to get the installer to run, it would take about 5 minutes and give the following kernel panic error

 

I would like to start again, maybe get install to run smoothly and choose the correct settings. I have an acer 5735z, here are the specs taken from everest ultimate edition

 

CPU Type Mobile DualCore Intel Pentium T4200, 2000 MHz (10 x 200)

Instruction Set x86, x86-64, MMX, SSE, SSE2, SSE3, SSSE3

Min / Max CPU Multiplier 6x / 10x

 

Front Side Bus Properties

Bus Type Intel AGTL+

Bus Width 64-bit

Real Clock 200 MHz (QDR)

Effective Clock 800 MHz

 

Mobile Intel® GMA 4500MHD

Video Adapter Intel GL40/GM45/GM47/GS45 Chipset - Graphics Controller 0 [b-3]

 

Wireless: Atheros AR5009 802.11a/g/n Wireless Network Adapter

Ethernet: Marvell Yukon 88E8071 PCI-E Gigabit Ethernet Controller

Audio: Realtek ALC268 @ Intel 82801IB ICH9

 

Any help would be appreciated. Oh and I'm installing on an External IDE hard drive.

 

PS:

When it doesn't load the installation disk, I get the following error

 

USBF: 0.455 AppleUSBEHCI[0x600a800]: unable to get filterInterruptedEventSource

USBF: 0.456 AppleUSBEHCI[0x600a800]: UIMInitialize - Error Occurred (0x******) (can't make the rest of the code out from photo)

USBF: 0.460 AppleUSBEHCI[0x600a800]: start unable to initialize UIN

mblnlt: done (64 MB memory set for mbuf pool)

 

Then the disk stops reading.

 

I just tried to boot the setup again, but just using -v -f cpus=2, I left out the bus ratio.

 

It got stuck on

Bug: launchctl.c:2325 (23930):39: (dbfd = open(g_job_overrides_db_path, 0_RDONLY | 0_EXLOCK | 0_CREAT, S_IRUSR | S_IWUSR)) != -1

 

2 minutes later it shows under it

systemShutdown false

 

This stays for a good 5-6 minutes while the CD is buzzing away, like the laptop is trying to find something. Afterwards, it loaded, but the touchpad wasn't moving. Brilliant.

 

Eitherway, if installation loads, and the touchpad works, the above bug and systemshutdown messages are shown regardless.

[camzgon]

no one?

[RenatoViolin]

Hi,

 

I´m experiencing the same problem as you. Mine is a Thinkpad T61, C2D T7300.

 

In my case, beside the erros, the system open the install dialogs.

 

Renato.