Jump to content
InsanelyMac Forum
dj nitehawk

[ PRE-INSTALL AUTOMATOR v1.1 ] for easily installing vanilla snow leo.

Recommended Posts

Thanks for the tutorial. DD's script looked a bit overwhelming for me so I gave yours a try.

The script was really easy to follow...but...

My mother board bios had all settings you mentioned except the intel xd. I tried a few different settings and reboots but all stopped at the same spot of the load.

Chameleon loads but during the white letters on black loading screen, it stops at a line that says "System uptime in nanoseconds:20344..."

Any ideas?

I've tried a few times with different kexts added and once with only the kexts you supplied for us. Same results though.

This is my first time to post. I hope I'm doing this right. My signature has my machine info. hope it shows up. :thanks_speechbubble:

Share this post


Link to post
Share on other sites
Advertisement
I did use uinstaller to use my gfi string everytning is fine except for the boot flag

 

there is some voodoo {censored}e happening with the -v flag... cos i cant get my machine to wake up from sleep if i dont boot up with the -v flag...

 

and i dont use 64bit cos i find 32bit on my system to be more stable... so cant really help with any 64bit stuff... cos i havent used 64bit much...

 

My mother board bios had all settings you mentioned except the intel xd.

 

it stops at a line that says "System uptime in nanoseconds:20344..." Any ideas?

 

dont worry about intel xd... my machine works fine with or without it... i only mentioned it only to be double safe...

 

i might be able to get a better idea of whats going on if i could see a pic of the error messages...

 

also, what type of hdd's u using? ide or sata? ahci enabled?

 

in the meantime:

 

confirm that the following file exists on your snow volume...

 

/Extra/dsdt.aml

 

cos if it didnt, that means there was a problem patching ur dsdt and the file didnt get created... most machines are unable to boot without a patched dsdt.aml file...

 

we'll take it from there...

Share this post


Link to post
Share on other sites

Thanks for your guide, by the way........Could I use your "DSDT.AML" for my Giga EX58 UD4P motherboard and BFG 9800GX2 1GB graphic card?

 

My PC: i7 920+ Giga Ex58 UD4P + BFG 9800GX2 + Samsung 750GB

Share this post


Link to post
Share on other sites

Hi many thanks for your hard work on this. Hoping to be able to get my system up and running with Snow Leopard with it.

 

I have a question you may be able to help with.

 

After completing your instructions, my PC runs through the Chameleon startup and runs the last line which is 'Starting Darwin x86' My screen goes blank and then it reboots.

 

Do you know what might be causing this?

 

I have Leopard running on the same machine but only with the following options set from the IPC OSX86 - UNIVERSAL 10.5.6 - PPF5 install Disk

 

9.4.0 STAGEXNU UNIVERSAL KERNEL

INTEL ICHx SATA DRIVERS (Chipset Drivers)

NVDARWEN256 (Video Driver)

APPLE AZALIA AUDIO (Audio Driver)

FIXES & PATCHES: CPUS=1 (ONE CORE FIX) & APPLE SMBIOS PATCH - (APPLESMBIOS TOH)

 

I would love to get the retail version up and running and have been trying for days to get this to work, any help would be much appreciated!!

 

My PC Spec is below, THANKS!

Jon.

 

 

Intel (South Lake 3 G5) 915GV Motherboard

Intel® Pentium® 4 processor 519 with Hyper-Threading Technology 
Operates at 3.06 GHz, 533 MHz FSB - Features MMX, SSE, SSE2, SSE3, NX-Bit, C1E

2GB 533 MHz (PC4200) DDR2 memory

NVIDIA GEFORCE 6200 256MB PCI Graphics Card

Realtek ALC860VU On Board Sound

Share this post


Link to post
Share on other sites

Cheers.. worked a treat on my Asus T3-P5G31-Q6600-GeForce 7300 GT all i had to do was put the 64 bit voodoo hda enabler on it and its flawless!

In 10.5 I used a spare hdd I had laying about to install with this util' and my retail 10.6 DVD, then i botted off it and repeated the process on the SATA HDD that 10.5 was on.

attached my DSDT and the HDA enabler I used.

 

Cheers again! :blink:

VoodooHDA_Pref.zip

dsdt.aml.zip

Share this post


Link to post
Share on other sites
Could I use your "DSDT.AML" for my Giga EX58 UD4P motherboard and BFG 9800GX2 1GB graphic card?

 

u can and should use the dsdt.aml that my script generates...

 

u should not use other ppl's dsdt.aml files unless their motherboard is exactly the same as urs... even then, if ur hardware config varies even the slightest bit, you will have trouble booting... for ex say that ur running a core2 duo processor and the person u borrowed the DSDT from is running core2 quad, u will not be able to boot with his/her dsdt.aml file...

 

if u are somehow able to run without the dsdt.aml by using "DSDT=nothing.aml" boot flag, your DSDT may be good enough for snow... most of us havent been that lucky :-)

 

i have never been able to get my intel dg33fb mobo to work fully without a patched dsdt.aml...

 

After completing your instructions, my PC runs through the Chameleon startup and runs the last line which is 'Starting Darwin x86' My screen goes blank and then it reboots.

 

im not familiar with running snow leo on pentium 4 systems... u could try doing:

 

1. disconnect ur 10.5 drive to see if snow is conflicting with that somehow

2. try using basic graphics by using "GraphicsEnabler=No" boot flag

3. try using "CPUS=1" boot flag

 

look at a guide for running snow on pentium 4 and see what specific requirements it needs...

 

Cheers.. worked a treat on my Asus T3-P5G31-Q6600-GeForce 7300 GT all i had to do was put the 64 bit voodoo hda enabler on it and its flawless!

In 10.5 I used a spare hdd I had laying about to install with this util' and my retail 10.6 DVD, then i botted off it and repeated the process on the SATA HDD that 10.5 was on.

attached my DSDT and the HDA enabler I used.

 

Cheers again! :P

 

beee aaa uuu tiii fuuuullll :-)

 

note to others: only use Jabbawok's dsdt.aml if ur config closely matches his...

 

thanks for sharing Jabbawok!!!

 

Sorry it does´nt work as so many of the other guides for that matter. Good try though

 

if u post screenshots of ur error msgs and tell us more about ur hardware config, we might be able to help :-)

 

then again we might not be :-)

 

ive tried installing snow for about 15 of my friends and only about 6-7 of those machines were able to run snow off the bat... the rest of them required custom attention and troubleshooting...

 

digital_dreamer says it best...

 

Building a 'hackintosh' is a technical acheivement

Share this post


Link to post
Share on other sites

Greatly appreciate your quick reply, you said I could use your DSDT.AML for my Giga EX58 UD4P. Is this mean, your motherboard is the same one as I have (UD4P) and 9800GX2 will also be supported by your DSDT?........Thanks a lot!

 

u can and should use the dsdt.aml that my script generates...

 

u should not use other ppl's dsdt.aml files unless their motherboard is exactly the same as urs... even then, if ur hardware config varies even the slightest bit, you will have trouble booting... for ex say that ur running a core2 duo processor and the person u borrowed the DSDT from is running core2 quad, u will not be able to boot with his/her dsdt.aml file...

 

if u are somehow able to run without the dsdt.aml by using "DSDT=nothing.aml" boot flag, your DSDT may be good enough for snow... most of us havent been that lucky :-)

 

i have never been able to get my intel dg33fb mobo to work fully without a patched dsdt.aml...

Share this post


Link to post
Share on other sites

Hi,

Im with P5QL-E video Gigabyte nvidia 8500GT

 

Some info because i try 2-3 methods

I restore image on partition and try to boot from it but have kernel panic or stuck on gray screen I can move mouse but 10 minutes nothing appears.I run with -v option but no output when i see gray screen

 

Im with 10.5.7 i flash my BIOS before install 10.5 but I dont need to upgrade it again or i need !?

 

Today I will try to change video with palit 9500GT and see what will happend.

Share this post


Link to post
Share on other sites
Greatly appreciate your quick reply, you said I could use your DSDT.AML for my Giga EX58 UD4P. Is this mean, your motherboard is the same one as I have (UD4P) and 9800GX2 will also be supported by your DSDT?........Thanks a lot!

 

ok let me explain... when u run the script it reads ur DSDT info from your actual bios, fixes the problems with it, and saves it at "/extra/dsdt.aml"... that file doesnt have anything to do with my motherboard at all... that file is totally specific to your bios/mobo/cpu etc...

 

thats why u shouldnt use other ppl's dsdt.aml files...

 

if u look inside the folders after u extract my zip file, there is no dsdt.aml file in there... it is only generated from ur bios after u run the script on ur machine...

 

the dsdt patching software is by a guy called Fassl from this forum... ive simply integrated it to my script to make things easier...

 

hope this explanation helps...

 

Hi,

Im with P5QL-E video Gigabyte nvidia 8500GT

 

Some info because i try 2-3 methods

I restore image on partition and try to boot from it but have kernel panic or stuck on gray screen I can move mouse but 10 minutes nothing appears.I run with -v option but no output when i see gray screen

 

Im with 10.5.7 i flash my BIOS before install 10.5 but I dont need to upgrade it again or i need !?

 

Today I will try to change video with palit 9500GT and see what will happend.

 

i dont really know about ur specific configuration but sounds like an issue with ur graphic card... have u tried booting with basic graphics? ie: without any efi strings/enablers etc for ur card...

 

if booting without graphic card support works, u gotta find out what works for ur specific g.card model...

Share this post


Link to post
Share on other sites

I don't put any EFI strings because i see in EFI i have over 8600 and I don't put anything

 

Today I will get from work palit 9800 and i will try without any EFI string when SL boot install then I will try to make full resolution and QE support

Share this post


Link to post
Share on other sites

Yeah sorry forgot to post what gear I have it´s:

GA EP45-DS3

Q6600

Sata drives

 

Typing this from SL using one of these 132 boot discs. Works 90-95% OK but I can´t boot without the disc not without loosing one of my videocards and I get really crappy resoloution on the dsiplay that do work.

 

The problem with this was it said it could´nt find my USB "stick" I´ll give it a shot again tonight.

 

Sorry if it came out bad was´nt my meaning it just that I´ve been trying out pretty many of these guides some work like the one I have now but some does´nt work at all, not for me anyway. Short story -frustration.

 

It seems also people add a DSDT.aml to every guide around and it´s hard to know if it just somekind of a standard/should work if you´re lucky or if the installationprocess gives you one that´s specific for your own hardware. You say I get one for my hardware but still it seems I have to edit it so I´m getting confused.

 

Also it´s hard to really get if this DSDT.aml really is the one and only key to get SL working or if it´s just the new thing so that´s why everybody´s heading in that direction. I have about four hacks at home and two more out of the house at the moment and I have never used DSDT.aml on any of them and they all run really good but on Leo though.

Share this post


Link to post
Share on other sites
Yeah sorry forgot to post what gear I have it´s:

GA EP45-DS3

Q6600

Sata drives

 

Typing this from SL using one of these 132 boot discs. Works 90-95% OK but I can´t boot without the disc not without loosing one of my videocards and I get really crappy resoloution on the dsiplay that do work.

 

dude u forgot to mention what graphics card u use... if its an nvidia card it should be real easy to get going... i've never used anything else with hacks cos nvidia has buitin support from the osx drivers...

 

 

The problem with this was it said it could´nt find my USB "stick" I´ll give it a shot again tonight.

 

where and when, does it say that??? i never coded in that error msg to my script so it cant be my script... if u dont like explaining, taking a snap and posting it would be the best thing...

 

Sorry if it came out bad was´nt my meaning it just that I´ve been trying out pretty many of these guides some work like the one I have now but some does´nt work at all, not for me anyway. Short story -frustration.

 

dont get discouraged bro... we've all had that... doing some research as to why things happen the way they do is the best way ive found to deal with frustration...

 

besides, hacking-macin-tosh-os is supposed to be a hobby and a fun thing to do... so dont take it too serious... if something goes wrong, just take a break and try again later... as they say, just flow with life, dont fight with life :-)

 

It seems also people add a DSDT.aml to every guide around and it´s hard to know if it just somekind of a standard/should work if you´re lucky or if the installationprocess gives you one that´s specific for your own hardware. You say I get one for my hardware but still it seems I have to edit it so I´m getting confused.

 

first off... u dont have to edit ur dsdt.aml file unless ur mobo is suffering from the bios/cmos reset problem...

 

Also it´s hard to really get if this DSDT.aml really is the one and only key to get SL working or if it´s just the new thing so that´s why everybody´s heading in that direction. I have about four hacks at home and two more out of the house at the moment and I have never used DSDT.aml on any of them and they all run really good but on Leo though.

 

ya ive never used a dsdt.aml with leo either... this snow leo is a totally differnt beast and having a fixed/patched clean dsdt is what enabled my leo to detect and boot into my sata drives and also fixed some problems with my sleep/resume functions... u should read up on what exactly DSDT is... just use google or look in the "tutorials/genius bar" forum here...

Share this post


Link to post
Share on other sites

Just have to type this to find this thread again, sorry I´ll reply as soon ......

 

See I have a few HDDs going here and the speed this board gets updated man it´s hard to keep up.

 

Back in a second

Share this post


Link to post
Share on other sites

th_MOV00064.jpg

 

Sorry forgot that, it´s two noname 7300gs 512 mb pcie videocards I found on ebay. Store´s in Hongkong. Check out the link over here. The resoloution is not so great cause I had to use my cellphone camera.

 

The strangest thing is they do work ok with this Slimbuild-preboot disc I downloaded and SL if I install an NVinject.kext I found here a while back (and edited myself). This kext works with a few other videocards too, got it uploaded here somewhere in hardware graphics in a thread of mine. I even get PS2 mouse and keyboard working ok booting with this disc using the old "PS2" kexts. But without booting with the disc I get only one card working and also only one display and only USB mouse and keyboard.

 

The case is I actually can boot without this disc and even without the DSDT.aml that comes with it, at least it seems so. You see I did a test install and installed a fresh SL to an USB harddrive and for what I know no DSTDT.aml or anything else besides what´s on the SL disc would´nt get installed if you do like this even if you use one of these 132 boot disc form around here.

 

Maby you can understand my frustration now I mean there´s just so many guides around here and I´m beginning to suspect you don´t need a DSDT.aml at all.

 

But I´m truly sorry if what I say here comes out wrong man it´s not easy writing in another language.

 

It go to late at night so I´ll have to wait till tomorrow before I can give your guide another try.

 

Thanks bud

Have it good as we say over here

 

I´m going to edit this reply if it shows my film/link overe here does´nt load ok

Share this post


Link to post
Share on other sites
.

 

ok try doing this...

 

1. extract my zip file to ur desktop

 

2. get the nvinject.kext (the one u have modified - which works on ur system) and also any other kexts ur system might need to boot, and place them here:

 

desktop/snow-installer/filez/extra/extensions

 

4. edit the following file:

 

desktop/snow-installer/filez/extra/com.apple.boot.plist

 

and change where it says "GraphicsEnabler=Yes" to "GraphicsEnabler=No"

 

5. restore the snow installer dvd to ur usb drive...

 

6. run "desktop/snow-installer/installnow" and select ur usb as the target

 

7. copy the "desktop/snow-intaller" to ur usb drive root folder

 

7. boot from the usb drive

 

8. launch terminal via "utilities" > "terminal" and type:

 

/snow-installer/installnow

 

then select where u wanna install snow as the target

 

9. exit terminal and continue with the snow installer

 

10. reboot and boot into ur new snow leo volume...

 

if that doesnt work dude i dont think i can be of any more service...

 

ps: just to be safe and to make sure that things dont confict... please try to install snow with this method to a clean HDD (where there are no other snow or leo installations)

 

do a clean install... wipe hdd first...

Share this post


Link to post
Share on other sites

Dear all!

I've done everything right by the guide, and so my SL is up and running. The only problem I have is that when I need to start-up from my HDD where SL lives, it doesn't boot, only the blinking cursor I see on top of the screen. No boot options available too. So the only way I can start-up is launching with F8 from my USB drive where I installed my SL from and choosing the drive with SL. I guess there's something with bootloader probably, nothing helps.

 

I'm not very good in MAC OS but aint a deep noob also. Could someone please help.

 

Thanks in advance!

Share this post


Link to post
Share on other sites
Dear all!

I've done everything right by the guide, and so my SL is up and running. The only problem I have is that when I need to start-up from my HDD where SL lives, it doesn't boot, only the blinking cursor I see on top of the screen. No boot options available too. So the only way I can start-up is launching with F8 from my USB drive where I installed my SL from and choosing the drive with SL. I guess there's something with bootloader probably, nothing helps.

 

I'm not very good in MAC OS but aint a deep noob also. Could someone please help.

 

Thanks in advance!

 

to make things easy, make sure ur SL partition is GUID, and not mbr...

and also if there are no other OS partitions (for ex: windows, linux, etc) on the same disk, that would help troubleshoot things too...

 

boot up into the SL installer on ur usb... run the script again in terminal "/snow-installer/installnow"

 

once the script finishes, scroll back up to the part where it says "installing chameleon boot0..." and take a snap of that screen and attach here... so we can have a look to see whats going wrong with installing the bootloader... (if u see no apparent erros on that screen, it might pay to take snaps of the rest of the screens too and attach here... so we can figure out whats going wrong...)

 

then try booting without the usb and into ur SL partition...

 

if still the same, boot back into SL on ur hdd using the help of ur usb and launch terminal...

 

type the following one after the other...

 

sudo fdisk -e /dev/diskX

f XX

w

q

y

 

replace the X with the disk number of the actual disk ur SL is installed on...

 

replace XX with the parition number of ur SL install...

 

u can get a list of disks by using the following command in terminal...

 

diskutil list

 

we'll take it from there...

Share this post


Link to post
Share on other sites

OK thanks I´ll give it a try, if it works drinks on me hehe. There´s a few things you say here in this last tip that looks interesting specially the line to make graphics not to load.

 

Well I´m 50+ maby the motor´s running a bit slow these days hehe.

 

Thanks for the help.

 

ok try doing this...

 

1. extract my zip file to ur desktop

 

2. get the nvinject.kext (the one u have modified - which works on ur system) and also any other kexts ur system might need to boot, and place them here:

 

desktop/snow-installer/filez/extra/extensions

 

4. edit the following file:

 

desktop/snow-installer/filez/extra/com.apple.boot.plist

 

and change where it says "GraphicsEnabler=Yes" to "GraphicsEnabler=No"

 

5. restore the snow installer dvd to ur usb drive...

 

6. run "desktop/snow-installer/installnow" and select ur usb as the target

 

7. copy the "desktop/snow-intaller" to ur usb drive root folder

 

7. boot from the usb drive

 

8. launch terminal via "utilities" > "terminal" and type:

 

/snow-installer/installnow

 

then select where u wanna install snow as the target

 

9. exit terminal and continue with the snow installer

 

10. reboot and boot into ur new snow leo volume...

 

if that doesnt work dude i dont think i can be of any more service...

 

ps: just to be safe and to make sure that things dont confict... please try to install snow with this method to a clean HDD (where there are no other snow or leo installations)

 

do a clean install... wipe hdd first...

Share this post


Link to post
Share on other sites

So here is where i am at now!

 

I followed the guide step by step, everything went well!!! wicked little guide!

 

There is a problem though.......

 

1.Booted from my sata drive where the SL install image/DVD was restored to.

 

2. Install of SL went 100% ok.

 

3. It asks me to restart after 100% install.....

 

3. rebooted then I get this panic when the new SL install drive boots.

 

Can anyone shine any light on this?

 

Would be great to sort it out! OH I forgot to say, I now no longer have a 10.5.8 install to work from!!

Only the Boot drive! and a broken SL install..... My system details are in my Sig.

post-431746-1253102147_thumb.jpg

Share this post


Link to post
Share on other sites
So here is where i am at now!

 

I followed the guide step by step, everything went well!!! wicked little guide!

 

There is a problem though.......

 

1.Booted from my sata drive where the SL install image/DVD was restored to.

 

2. Install of SL went 100% ok.

 

3. It asks me to restart after 100% install.....

 

3. rebooted then I get this panic when the new SL install drive boots.

 

Can anyone shine any light on this?

 

Would be great to sort it out! OH I forgot to say, I now no longer have a 10.5.8 install to work from!!

Only the Boot drive! and a broken SL install..... My system details are in my Sig.

 

{censored} on a cracker mate!!!

 

okkay... by the looks of the error msg it looks like u've installed SL onto an IDE harddisk (or maybe even a laptop)... is this assumption correct?

 

if ur SL does not reside on an IDE hdd (or a laptop), please tell me what ur hardware config is and what additional kexts u have added in step 3 of the guide...

 

also helps to make sure that all ur hdds are running in AHCI native mode by going through ur bios settings...

 

so if u r using an ide hdd (or a laptop) - or even if not, just try doing the following:

 

1. download the attched file, extract it and place the kext at "/snow-installer/filez/extra/extensions" on ur SL INSTALLER drive (the one that u restored the image to)...

 

2. boot into the installer again, launch the terminal and run the following commands

  • rm -R /volumes/NAME-OF-UR-SL-VOLUME/system/library/extensions/ioatafamily.kext
  • kextcache -u /volumes/NAME-OF-UR-SL-VOLUME

3. when the above is done, run my installer script again, without quitting terminal with the following:

  • /snow-installer/installnow

4. boot into ur SL drive...

 

if that didnt work, reboot and while chameleon is starting, interrupt it by pressing the down arrow key and select "ignore boot caches" and select ur SL drive with the left/right keys and hit enter...

 

if that didnt work, tell me all about ur hardware config...

 

My system details are in my Sig.

 

ooooops..... sorry i missed that part.. yeh so ur using the badaxe mobo...

 

yeh just take the above steps to remove the ioatafamily thing on ur SL drive and u should be good...

 

let us know...

 

.

 

just found this:

 

http://www.insanelymac.com/forum/index.php...t&p=1256148

 

by the looks of it, u might not need to add the attached kext... just need to delete the stock kext from ur SL installation...

 

I use Terminal to input following

 

sudo rm -rf /Volumes/XXX/System/Library/Extensions/IOATAFamily.kext/Contents/PlugIns/AppleIntelPIIXATA.kext

 

XXX is the Label of you drive.

 

so first try only deleting the file as instruction in the quoted text above.... if that didnt work, try my initial instructions (add kext + delete file)...

 

report back what happens......

IOATAFamily.kext.zip

Share this post


Link to post
Share on other sites

Hey man, thanks for getting back to me.

 

I mounted the DVD of SL onto a sata external drive, The target drive is a ITB westeren digital sata 2 drive.

I deleted the AppleIntelPIIXATA.kext from the mounted DVD SL drive

 

1. Mounted the image to the drive with MBR, followed your steps, added Nait.kext for my video Card ...all went well!

2. Rebooted.

3.Formated the Target 1TB drive with GUID

4. Ran your scrpt again. all went well.

4.installed SL no problems at all.

5. rebooted and get Kernel Panic.....

 

Now its stuck on this KP and no matter what I chage in the Bios, It wont work....

 

I will report back!

 

thanks for your help

 

Do I need to remove IOATAFamily.kext or just AppleIntelPIIXATA.kext which is inside that kext?

 

I removed AppleIntelPIIXATA.kext but still getting the same KP

 

Tried booting with "Ignore Boot caches" but same KP again.

 

Defo need to write a Bad Axe 2 Guide for SL. Bios info etc etc.

 

Thing is its boots fine and installe 100% then I reboot and BOOM! KP!

 

Must be something I missed!

Share this post


Link to post
Share on other sites
Hey man, thanks for getting back to me.

 

I mounted the DVD of SL onto a sata external drive, The target drive is a ITB westeren digital sata 2 drive.

I deleted the AppleIntelPIIXATA.kext from the mounted DVD SL drive

 

1. Mounted the image to the drive with MBR, followed your steps, added Nait.kext for my video Card ...all went well!

2. Rebooted.

3.Formated the Target 1TB drive with GUID

4. Ran your scrpt again. all went well.

4.installed SL no problems at all.

5. rebooted and get Kernel Panic.....

 

Now its stuck on this KP and no matter what I chage in the Bios, It wont work....

 

I will report back!

 

thanks for your help

 

Do I need to remove IOATAFamily.kext or just AppleIntelPIIXATA.kext which is inside that kext?

 

I removed AppleIntelPIIXATA.kext but still getting the same KP

 

Tried booting with "Ignore Boot caches" but same KP again.

 

Defo need to write a Bad Axe 2 Guide for SL. Bios info etc etc.

 

Thing is its boots fine and installe 100% then I reboot and BOOM! KP!

 

Must be something I missed!

 

others only say u need to delete AppleIntelPIIXATA. but if ur KP still says AppleIntelPIIXATA that means it hasnt been deleted... not properly anyways...

 

did u delete it from the DVD installer partition or ur ultimate/target snow partition? u should delete it from everywhere...

 

if that doesnt work together with "ignore boot caches", go ahead and delete ioatafamily.kext from both locations... that kext is for IDE drives... if u dont have any IDE u can safely remove it... which looks like the cause of KP on bx2...

 

can u take a snap of the KP after removing the culprit kexts?

 

.

 

look here:

http://wiki.osx86project.org/wiki/index.php/HCL_10.6.0

 

search for the text "badaxe2" and read the notes there...

 

gotta delete that kext...

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Posts

    • HWMonitor2 v2.1.0rc3:  
    • There are new Bios updates that came out. I think these were to address the security defects in the kernel?   I updated both my 790 and 990 without issue.
    • Crack download software petromod v2016.2 GeoTeric v2017 paleoscan v2016.1 Leica CloudWorx v6.2 techlog v2016.1
      ttmeps#gmail.com ----- change "#" to "@"
      Anything you need,You can also check here: ctrl + f
        midas civil 2018 v1.2
      symmetre r410
      CP-Studio
      kepware 5.20
      saia PG5 2.1
      Motocom32 dx200 plus
      procon-win 3.5
      midas soilworks 3.5
      geostudio 2012
      technet GMbH PreDesigner 2017
      framecad structure v8
      csi preform 3d v6
      geogiga seismic pro 8.3
      citect 7.2
      3dbody 7.0
      3shape convince
      plastycad
      hypermill 2018
      deswik suite 2017.1
      Scania XCom 2.30
      tebis 4.0
      3shape implant studio 2017
      Cape pack V2.15
      Prinect Signa Station 2017
      exoplan 2017.03
      MagiCAD 2018 
      ExoCad 2017.12
      MillBox 2016
      GOM ARAMIS 6.15
      Blue Sky Plan v3 x64
      Maestro 3D Dental Studio 4
      Sirona InLab 4.2.5
      Maestro Ortho Studio Build 2.8
      Zirkonzahn 2017
      Dolphin Imaging 11.9
      Digital Smile System 1.9.8
      PlastyCAD 1.7
      3Diagnosys 4.1
      ArKaos MediaMaster 5.0.3
      smile designer pro v2.6.1 
      GEO5 2017
      TRUSS4 v10
      exocad Partial Framework 2017
      OnDemand3D Application 1.0.10.5385
      Dental Master 2016 
      Dental Wings (DWOS) 2016
      Ekahau Site Survey 8.6.1
      HYPACK 2016
      Dental Shaper
      Orcaflex 10.0e
      AQWA
      MOSES
      NAPA 2017
      offpipe
      maxsurf
      DNV GL AS PHAST
      DNV safty offshore 7.2
      aveva bocad suite 2.2.0.3
      AVEVA Engineering v14.1 SP1
      Aveva everything3D (E3D) v2.1
      napa ship designer
      numeca fine
      marine 3.1
      Veristar Hull, Stability, Homer, Optimise
      Hydrostar, ariane7
      AVEVA Marine 12.1 SP4.29
      sacs 11.0
      DNV Sesam all moduels
      Leica GEOMOS v5.0
      Rocscience RS3
      3shape orthodontic 2017
      Onyx ProductionHouse v12.1
      pc-dmis 2018
      exocad DentalCAD 2.2 Valletta
      exocad 2018
      frontline genflex 3.2c1
      frontline genesis 10.02
      ez-fixture 9.6.4
      ezgrid 9.5
      ucam 10.2
      em-test expert v8
      3shape design system 2017 2.17.3.0
      PC-DMIS 2018R1 x64
      Motor-CAD/Motorcad 11.1.5
      Synopsys Synplify FPGA 2017.09 Win&Linux FPGA
      Golden Software Strater 5.4.948
      Golden Software MapViewer 8.6.651
      Waterloo Visual MODFLOW Flex 2018.v5.1
      Cype 2017m
      Intergraph SmartPlant Spoolgen Isometrics 2014.v08
      Intergraph SmartSketch 2014.v08.00.00 R1
      Intergraph CAESAR II 2018 v10.00.00 x64
      Intergraph SmartPlant P&ID 2014 R1
      IHS QUE$TOR 2017 Q1
      Intergraph SmartPlant Review 2017 v12.00.00.0501
      ANSYS Apache Totem 14.1 Linux64
      Crosslight Csuprem 2018 x64
      Ensoft LPile 2018.10.02
      AnyBody Modeling System 7.1
      Antenna Magus 2018.0.v8.0 x64
      CGERisk BowTieXP 9.0.1
      PDI GRLWEAP Offshore Wave 2010-7
      NI AWR Design Environment with Analyst 13.03 x64
      Rock Flow Dynamics RFD tNavigator 2017.v17.3 x64
      CMG (Computer Modelling Group) Suite 2017.10
      PHDwin2.10.3
      meyer 12 2017.12
      Schlumberger petrel 2017
      HampsonRussell Suite 10.3 
      geoview 10.3 HRS 10.3
      Midland Valley move 2018.1
      jason 9.7
      Schlumberger CoilCADE 6.0
      Schlumberger StimCADE 4.0
      crystal 2018.1
      gohfer 9.0.1.6
      omni 2017.1
      tesseral pro 5.0.3b
      ERDAS IMAGINE 2018
      Waypoint Inertial Explorer 8.7
      Deswik suite 2017
      FAROBox PointSense plant 18.5
      EyeRadar 2.0
      Leica Xpro 6.4
      Trimble EdgeWise_v5.0.2SP1
      Trimble Business Center 4.0
      3DReshaper 2017 x64
      Amberg Tunnel 2
      virtual surveyor 3.6
      cloudworx for revit
      socet set 5.6
      socet GXP 4.1
      OrbitGT
      Riscan PRO 2.0 x64
      JAR reconstrucer 3.3.0 x64
      Materialise E-stage v6.6
      Virtual Surveyor 3.5
      CARIS HIPS and SIPS 10.2
      DP-moderler
      APS 7.6
      Imagestation SSK 2015
      Deswik 2017.2.1234
      EnterVol 2017.4 for ArcGis
      Geochemist Workbench 11.0.8
      Maptek Vulcan 10.1.4
      Tesseral Pro 5.0.3
      Tesseral 2D 7.2.8
      Global Mapper 19.0.2
      GEOVIA Surpac 6.8
      Ventsim 4.8
      MineSched 9.1.0 x64
      Paradigm 17
      VUMA3D-NETWORK 2018
      MineSight 12.0
      Maptek Eureka 4.1
      whittle 4.7.0.1
      Leapfrog Geo 4.0
      Leapfrog Geothermal 3.2
      Leapfrog Hydro 2.6
      OptiSPICE 5.2
      VPI transmission maker 9.8 x64
      VPI photonics Analyzer 9.8 x64
      VPI componentMaker 9.8 x64
      socet gxp 4.3
      GEOVIA GEMS 6.8.1
      GamaPrintPro
      PosterShop
      RipCente
      ProductionHouse 12
      neoStampa 8.1.5
      Fiery XF v6.5
      ORIS COLOR TUNER WEB 3.1
      ORIS PRESS MATCHER WEB 1.4
      FlexiSIGN & PRINT 12
      PhotoPrint 12 Cloud
      ColorGate V10
      neo Textil
      ACRORIP 9.03
      ErgoSoft RIP 15
      3shape trios 1.4.7.4
      OptiSystem 15
      plaxis 2D 2017
      plaxis 3D 2017
      Rocscience SLIDE3 V2017.010
      Rocscience SLIDE V7.029
      Rocscience RocData v5.008
      Rocscience RS3 v2.005
      Rocscience RS2 phase2 v9.023
      ITASCA 3DEC v5.20.250
      ITASCA Griddle v1.0.1
      ITASCA UDEC v6.0.323
      ITASCA PFC v5.0.32
      ITASCA Flac3D V6.0.48
      ITASCA Flac v8.0.443


×