Search the Community: Showing results for tags 'enable hd4000'.
Found 1 result
llsiddhantll posted a topic in OSx86 10.9 (Mavericks)Hey everyone! First post here. I've been following this website for quite some time now, only joined recently. I am a fairly experienced Hackintosh user, but this time I've seem to have run into an unusual problem. I am trying to get Mavericks 10.9.1 to install. (that is the version I downloaded on my real Mac, and that is what I use to create the installer). Intel HD4000 Graphics does not seem to work at all. I've tried tons of stuff, but I can't get it to work. When I remove AppleIntelFrameBufferCapri, it does boot with additional flags, but I have no acceleration. When I put it back, it refuses to boot, getting stuck at [iOBluetoothHCIController] -- Connected to transport successfully -- I think, it finishes booting, but cannot load graphics, so cannot display anything. But that's just my guess. I'll walk you through all the steps that I took, along with everything that I have tried so far, without results 1. Created installer disk manually, and also tried using MacPwn By Niresh. 2. Applied MBR Patch, for dual booting with Windows. 3. Could get to the installer without using any boot flags. 4. Installed OS X on an MBR partition. 5. After installation, I cannot get to the OS directly, I enter Safe Mode using flags: -v -x GraphicsEnabler=No IGPEnabler=No , and finish the setup successfully. 6. I install FakeSMC, NullCPUPowerManagement (to avoid a KP that occurs if I don't), Ethernet, Audio drivers etc. 7. I apply a MacBookPro 9,1 SMBIOS. So far, I haven't touched graphics at all. 7. I try to boot into OS X, fail. When I try to reboot into safe mode, everything is working except graphics. Now, I have been told that Intel HD Graphics works out of the box with Mavericks, but in my case, it just doesn't. I've tried using a DSDT (which I don't know much about), but that didn't make a difference, so I removed it. My ig-platform-id is 0x01660009, as told by 'About This Mac'. I've tried manually injecting this ID, along with others, using the Chameleon boot flags, and also by adding it to com.chameleon.boot.plist I've tried patching my AppleIntelFrameBufferCapri.kext in 2 ways: 1. I opened the AppleIntelFrameBufferCapri executable in /S/L/E/AppleIntelFrameBufferCapri.kext/Contents/MacOS using HexFiend, and changed the hex values. I used this guide: OSXLatitude. This was a total disaster, all I got was a black screen, and I didn't really understand what I was doing, so it made me uncomfortable. The next one was much more promising. 2. I opened the Info.plist inside AppleIntelFrameBufferCapri and added my platform-id in IOPCIPrimaryMatch, and injected 0x01660009 using Chameleon. With some luck, I was able to boot into the installation without safe mode. But graphics were laggy, of course, because of no acceleration. I also tried removing all AppleIntel* , ATI* , And GeForce* Kexts from the /S/L/E/ folder, and that allowed me to boot, but again, no acceleration, which is kind of obvious, because I removed all kexts. Also, in 'About this Mac', it shows me that I have Intel HD 4000 Graphics with 64Mb sometimes, and when I remove all the above kexts, it shows me Display 5Mb (No surprise there). I also rebuild my cache etc. using KextUtility every time I make changes to the /S/L/E folder. For now, I have UseKernelCache=No to avoid any problems. If Graphics works, I'll add it to com.chameleon.boot.plist I read somewhere that I needed to disable VT-d to make it work, but I checked and my processor does not support it, so that's not an issue. So, ultimately, I am stuck now because everything works except Graphics, and I can't really use it without QE/CI because of the flashing lines. Can anyone please help me out here? I've been at it for days now, and I can't seem to find any solution anywhere that works for me. I was also thinking of downgrading to something like ML, Lion or even SL (sigh), if graphics works, and then upgrade from there? I haven't tried it though. I'm so desperate right now, I can try anything My laptop configuration: Intel Core i7-3630QM @ 2.4GHz (Ivy Bridge) Intel HD 4000 Graphics Nvidia GT 650M w/ 2GB VRAM 16GB DDR3 RAM Can't really provide motherboard information, as it is a custom one by Samsung. My laptop is the Samsung NP550P5C-S05IN. Please ask for more info if required Thanks a lot for any help that you can offer! P.S. I'm re-installing vanilla OS X right now, so whatever fixes you guys tell me do not conflict with stuff I've already tried. You can assume I have a clean installation.