Jump to content

tkenney65

Members
  • Content count

    9
  • Joined

  • Last visited

About tkenney65

  • Rank
    InsanelyMac Protégé

Profile Information

  • Gender
    Male
  1. OK.....so I successfully installed Snow Leopard. My one lingering issue is that after I shutdown the system normally within SL, when I start it up again the system behaves as if I had an improper shutdown (e.g. pushed in and held the power button). The system will not start up unless I do a hard reset (pull power plug, hold power button in for 10 secs). As you can imagine, this is very frustrating to do every time I want to use the system. My mobo is a Gigabyte GA-P45-UD3P Please help!!!! Tim
  2. Cannot Fix CMOS Reset Issue GA-P45-UD3P

    My mobo is a Gigabyte GA-P45-UD3P rev 1.6 BIOS is 6.0. Previously I successfully installed Snow Leopard via [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] with no post installation issues.. More recently I successfully installed Lion via [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and a second time via Cakewalk with one issue. I am unable to overcome the issue of the CMOS resetting itself both after sleep and also EVERY time I shut down the system. With help from folks across several forums I have attempted to: patch the AppleRTC.kext via terminal app.; replace the Lion AppleRTC.kext with the Snow Leopard one; modifying my DSDT with a DSDT Editor and so on... I am about at the point of going back to Snow Leopard because I just can't seem to fix this issue so I am hoping someone can assist. I can post my DSDT file if that helps. Thanks... Tim
  3. Noob Question on Patching AppleRTC.Kext

    Unfortunately this didn't work either. I appreciate your help though. I should probably take this to the DSDT Forum
  4. Noob Question on Patching AppleRTC.Kext

    It was under RTC....here is it Device (RTC) { Name (_HID, EisaId ("PNP0B00")) Name (ATT0, ResourceTemplate () { IO (Decode16, 0x0070, // Range Minimum 0x0070, // Range Maximum 0x00, // Alignment 0x02, // Length ) IRQNoFlags () {8} }) }
  5. Noob Question on Patching AppleRTC.Kext

    I successfully extracted my DSDT but it isn't finding any "RTC0" when I use the search editor? Is that even possible?
  6. Noob Question on Patching AppleRTC.Kext

    Here's what i entered in Terminal to apply the patch sudo perl -pi -e 's|\x75\x30\x44\x89\xf8|\xeb\x30\x44\x89\xf8|; s|\x75\x3d\x8b\x75\x08|\xeb\x3d\x8b\x75\x08|' /System/Library/Extensions/AppleRTC.kext/Contents/MacOS/AppleRTC Then a ran the kext utility app. Is there any way (other than the CMOS reset issue going away) to confirm what I did worked? Where is the best place to start to attempt this fix via patching via DSDT?
  7. I am trying to patch AppleRTC.kext to eliminate the CMOS reset issue on my Gigabyte GA-P45-UD3P mobo. I tried it (via Terminal) and the CMOS resets continue. Do I have to modify S/L/E folder permissions or the file permissions to apply the patch? Should the "Modified" date on the kext change after I do this? This is the last thing I need fixed to have my Lion Install work completely and I have been pulling my hair out for 2 weeks over this.
  8. I am trying to patch AppleRTC.kext to eliminate the CMOS reset issue on my Gigabyte GA-P45-UD3P mobo. I tried it and it doesn't seem to work because the "Modified Date" on the file isn't changing. Do I have to modify S/L/E permissions to apply the patch?
  9. Followed the guide above for my P45-UD3P and Lion installed great but I continue to have issues when starting up the system after shutdown. Every time I shutdown the system I have to reset the CMOS to get the system to start back up. I have to: Pull the power cord Hold in the power button for 10 secs Plus the power cord back in This is required after every single shutdown (not just sleep). Any ideas? Tim
×