Jump to content
Welcome to InsanelyMac Forum

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.


  • Content count

  • Joined

  • Last visited

About x111

  • Rank
    InsanelyMac Protégé
  1. I updated to 10.8.2 and installed these drivers for my GTX 560ti (just ran the installer) but it didn't have any effect on the problem whatsoever. Is there something else I should've done? I have no idea how to fix this. I wrote more about this here Turning off the secondary display produces artifacts, a blue screen and then a crash on GTX 560ti Thanks guys
  2. I have plugged a projector (Panasonic AX200) in my graphics card's (GTX 560ti) secondary DVI port with a DVI-HDMI cable. In the primary port there's my BenQ monitor (DVI-DVI). I had no problem's for the first few months with this setup but this has been going on for a few weeks now: when I turn off the projector and turn the monitor back on, after a few seconds strange artifacts appear on my monitor, mouse cursor stops moving, keyboard stops working and everything freezes. If I don't press reset, the screen usually turns blue eventually. What's causing this and how to solve it? I don't have any power saving settings enabled and no screen savers. I have set up the projector to show an extended desktop. I read the thread " NVIDIA GTS 450 - "Blue Screen" after changing resolution" and updated to 10.8.2 and installed the Nvidia drivers as recommended there as a solution. It didn't have any effect on my problem however. Here's a photo of what happens: http://i.imgur.com/liSZE.jpg Does anyone have any ideas on how to fix this? Thanks!
  3. Hello everybody! I recently crossflashed my P5K SE to P5KR to get AHCI enabled on my mobo. After configuring BIOS correctly, I boot with a DVD with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] on it. I get to the screen where I can see the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] disk and my 2 SATA harddisks (they are in SATA slots 3 and 4, for some reason BIOS doesn't recognize them from slots 1 and 2). I eject [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and put in the OSX installation disc. After I hit f5 one time, the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] disappears. After I hit f5 another time, another disc appears on the right side of harddisks, but the text place below disc images that normally tells the name of the disk distords somehow and [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] crashes, I cannot but boot. Here's a photo of that: http://dl.dropbox.com/u/8798004/2011-02-23%2002.01.49.jpg Then I burned a DVD with EmpireEFI on it, and booted with that. I again get to the disc selection screen, and after I eject EmpireEFI and put in the OSX installation dicsand hit f5, I can choose my OSX installation disc. But after I choose that and hit enter, I get kernel panic. Here a photo of that: http://dl.dropbox.com/u/8798004/2011-02-23%2001.59.04.jpg I'm dying to get this to work but have no idea what to do next. I have removed all unnecessary PCI-cards and USB-drives from my computer. The curious thing is that without [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] or EmpireEFI, I'm able to get to Mac installation just by booting with OSX installation disc. Before crossflashing (so I wasn't able to set SATA configuration to AHCI, but only IDE), I was able to install OSX with no problems. I just couldn't start it after booting after installation, it just gave me kernel panic. After crossflashing I'm still able to get to OSX installation but in the "disk utility" I cannot see any of my harddisks. My computer specs are: -Asus P5K SE (with P5KR bios now) -Intel E6750 processor -9800GT -2GB of RAM -External Samsung DVD-writer/reader -2 SATA harddisks (in slots 3 and 4) On another SATA disk I have Windows 7 installed but I'm unable to boot to that too after crossflashing my BIOS. Can anyone please guide me from here, what could be the problem, is there a problem with my hardware or am I doing something wrong? I followed this guide http://tonymacx86.blogspot.com/2010/04/ibo...ac-os-x-on.html and downloaded [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] from the link at step 2. My installation disk is 10.6.2. Thank you so much for any help! ps. I read somewhere that it might be helpful to try install with -v -x so I did that in EmpireEFI (also in EmpireEFI some part of the screen is distorted same way like [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] but I'm still able to hit enter on the disc) and I get this kind of screen (kernel panic) (if the information on the screen is helpful, I can try to get more of that for a new photo): http://dl.dropbox.com/u/8798004/2011-02-23%2002.39.56.jpg