Jump to content

as1serge

Just Joined
  • Content count

    5
  • Joined

  • Last visited

About as1serge

  • Rank
    InsanelyMac Protégé
  1. Dear peoples. I have Acronis Loader multiboot on SATA partitions (XPx64, Win7 and Snow with Chameleon loader); Everything worked fine. I've just added extra IDE HDD formatted NTFS to computer. Acronis loader works and boots into other systems where this HDD is visible and read/write is OK. But when I chooze to boot into SnowL via Chameleon it freezes with black screen and cursor blinking. If I disable this new IDE HDD detection in BIOS and it is not seen anymore, everything is fine as was before, so the problem is obviously with adding this extra HDD. Please help me what could be done, please. Thank you
  2. Darwin Bootloader FAQ

    Dear people. I have Acronis Loader multiboot on SATA partitions (XPx64, Win7 and Snow with Chameleon loader- Darwin); Everything worked fine. I've just added extra IDE HDD formatted NTFS to computer - it is empty now no OS. Acronis loader works and boots into Win systems where this HDD is visible and read/write is OK. But when I chooze to boot into SnowL via Chameleon it freezes with black screen and cursor blinking. If I disable this new IDE HDD detection in BIOS and it is not seen anymore, everything is fine as was before, so the problem is obviously with adding this extra HDD. Please help me what could be done, please. Thank you
  3. Oh, thank you. I did everything by the book and SL installed quite smooth. I also installed NVKush for GF 8800GT and it gave 1280x1024 75 Hz. There were some mistakes in DSTD patching, though, resulting in '...couldn't built etc...', maybe its the reason that SL seems to run a little bit slower than 10.5.8 also installed on PC or maybe because I installed SL on USB disk for testing purposes. Could you tell please if SL could be loaded in 64 bit mode - system info says software is not in 64 mode - maybe some 64 bit kernel should be used? Some people say the if you press 6 and 4 during loading it will load in 64 mode but I haven't managed to suceed... Thank you again
  4. Dear Agrafuese, thank you very much for your how-to instructions. The system is Ducky OSX86 10 5 4 AMD ONLY SB600 SB700 installed on SATA (AHCI) AMD Phenom 2 M3A78EM and GEforce 8800GT - I could not install any other OSX revision because only in this one SB700 drivers are included. I installed Chameleon -EFI because could not find any EFI v8 for AMD (I suppose it is for Intel only) After step by step installation of EFI strings based on your guide (I could not patch OpenGL files on restart though because responce was that command lines in files are different from patch options, but I think I've managed to patch them later with Marvin's AMD utility). So the card works but QE is not supported still nVidia GeForce 8800 GT: Chipset Model: nVidia GeForce 8800 GT Type: Display Bus: PCIe PCIe Lane Width: x16 VRAM (Total): 512 MB Vendor: NVIDIA (0x10de) Device ID: 0x06e4 Revision ID: 0x00a1 ROM Revision: nVidia GeForce 8800 GT OpenGL Engine [EFI] Displays: BenQ FP991: Resolution: 1280 x 1024 @ 75 Hz Depth: 32-Bit Color Core Image: Software Main Display: Yes Mirror: Off Online: Yes Quartz Extreme: Not Supported QuartzGL: Supported Display Connector: Status: No Display Connected Could you please advise what had I done wrong and maybe guide me what other actions with EFI strings (I already tried EFI Studio and OSx86 tools but in vain) could be done? Nvinject etc is also not working Thank you P.S. maybe somebody have a working link to QuartzSimple - this program can activate QE I've read...
  5. Doesn't work for me. SATA (AHCI mode) HDD and DVD are not visible - installed as per instructions on USB HDD with PC drives disconnected, installed kexts, repaired permissions (maybe I should have done this?), rebooted with drives attached - nothing happened...\Apart from that everything works fine Trying to find this Ducky OS X...seems it is gone from torrents...
×