Jump to content


  • Content count

  • Joined

  • Last visited

About Vega16

  • Rank
    InsanelyMac Protégé
  1. Hello. I have an ASUS A8M2N-LA motherboard and successfully installed zephyroths mac 10.5.2 rev2. It works fine and all however I want to use 10.5.5. Is there any way to update to that? I did before try installing Ideneb v1.3 10.5.5 and it did not work. I was instructed to try a diff 10.5.5 install such as leo4all, iaktovos, etc. Not sure if they will work with my mobo but its worth a shot. Any feedback on this issue is appreciated.
  2. Hello all. I have installed mac on my pc and it works fine and no problems. I then installed vista as well and my comp auto booted into vista. I then set up a dual boot for mac and vista. At startup selecting vista works fine and vista boots fine. However selecting mac just takes me to a message that says CHAIN BOOT ERROR. I have used easybcd and no luck. Any help is appreciated.
  3. I have tried 9 times on diff ideneb installs and had no success at all. My mobo is a A8M2N-LA (NodusM3). Can someone please recommend an install whether it is iakto,ideneb,kalway,zephyroth, or anything else out there. Here are my full specs Motherboard description Motherboard manufacturer's name: ASUS A8M2N-LA HP/Compaq name: NodusM3-GL8E CPU/Processor Socket: AM2 Supports AMD Athlon 64, Athlon 64 X2, and Sempron processors Front-side bus (FSB) 2000 MegaTransfers/second Chipset GeForce 6150 LE chipset BIOS features Award brand system BIOS Keyboard combination to used to enter BIOS: F1 Form factor Micro-ATX: 9.6 in X 9.6 in Memory Four 240-pin DDR2 DIMM sockets Supports PC 4200 (533 MHz) and PC2 5300 (667 MHz) DDR2 DIMMs non-ECC memory only, unbuffered Maximum HP/Compaq approved memory is 4 GB* NOTE: *Actual available memory may be less Expansion slots Three PCI One PCI Express x16 graphics Video graphics Integrated Serial ATA 4 SATA connectors Each connector supports 1 serial ATA-150 disk drive Onboard audio Built-in High Definition 8 channel audio ALC888 CODEC Onboard LAN 10/100 Marvell 88EC031 Back panel I/0 Listed in physical order from left to right: One PS/2 keyboard port (purple) One PS/2 mouse port (green) One SPDIF (coaxial) out One VGA port One IEEE 1394 Four USB 2.0 One RJ-45 networking port Audio ports: side speaker out (gray) rear speaker out (black) center/subwoofer (yellow orange) line in (light blue) line out (lime) microphone (pink) Internal connectors One 24-pin ATX power connector One 4-pin ATX power connector Two PATA connectors Four SATA connectors One floppy drive connector Two 12v fan connectors for CPU fan and PC fan One 9-pin header for power button, reset button, power LED, and HDD LED One audio header for headphone-out and microphone-in One audio header for line input Two USB 2.0 connectors supporting 4 additional USB 2.0 ports One IEEE 1394 connector
  4. 2009 Live DVD

    Question This live did sounds good and my comp I would like it has 2gigs of ram as opposed to 1 so I should be decent as far as using it if not pretty good. I am curious and maybe this is dumb but this live dvd does boot off the disc correct? Does that mean that once the dvd is removed or pc powered off that anything you do on this mac os on this live dvd is all gone? or does it just save to a directory like an external hd and then open that the next time u use the live dvd. Also could I install iphone SDK with the live dvd and use it without errors? That is all
  5. Hello everyone. I have downloaded, burnt, and installed a copy of Ideneb 10.5.5 on my amd desktop. I have installed 8 times and failed each time. The installation go's well but never boots afterwards. After doing reseach I decided to come here and try this install of leopard. I have not yet downloaded it but will shortly. My desktop is a Hp m7664x with a A8M2N-LA (NodusM3) motherboard and my labtop is a Hp dv9620 us. The ideneb copy would never show my hd's on my labtop at disk utility when I wanted to format them and this is possibly due to it being SATA but I am not sure but my desktop always showed it. I installed to desktop and partition and formated before the install of course. Tried many diff kernals and chipsets but no luck. I am curious as to those two pc's that I listed if anyone here can help me and tell me possibly ahead of time if this distribution of leopard will work. If you do not know what I am talking about I am speaking of iatkos v5i.