Jump to content
InsanelyMac Forum

Outlawz85

Just Joined
  • Content count

    3
  • Joined

  • Last visited

About Outlawz85

  • Rank
    InsanelyMac Protégé
  1. First build didnt know that.. thanks bud
  2. Update: i downloaded Lilu kext and Whathevergreen Kext and put them in my kext folder and one monitor is working.. Any way to get both? the 2nd monitor i still have to power off then on
  3. This is my first hackintosh Build.I installed windows 10 and made sure everything was working theni Change my bios settings. (See Below)I Created a ##### usb with latest version of high Sierra 10.13.4 then installed it after erasing the whole driveBooted into MacOS then ran [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] with these settings below then that when i Get the black screen after clover boot screen then i have to turn off the monitor and turn it back on to get a picture on one of my monitors.. I have 2 Ethernet is workingMOTHERBOARDGIGABYTE Z370 AORUS Gaming 5CPUIntel Core i7-8700K Desktop Processor 6 Cores up to 4.7GHz Turbo Unlocked LGA1151 300 Series 95W BX80684i78700KGraphics CardGigabyte AORUS Radeon RX 580 8G 8GB GDDR5 256bit Graphics Card GV-RX580AORUS-8GDCoolingNZXT Kraken X62 All-in-One 280mm CPU Liquid Cooling SystemSsd HardriveCrucial MX300 1TB 3D NAND SATA M.2 (2280) Internal SSDMemoryG.SKILL TridentZ RGB Series 16GB (2 x 8GB) 288-Pin DDR4 3000MHz (PC4 24000) CASENzxt S340VR Elite Computer CaseBluetooth / WIFi (removed onboaard wifi and put this card)Broadcom BCM94352Z M.2 NGFF 802.11AC 867Mbps BT 4.0 DW1560 for Mac HackintoshPower supplyEVGA SuperNOVA 650 G3 650W 80 Plus Gold Modular Power Supply##### Settings Quick Start - UEFI Boot Mode Drivers Audio - Misc FakeSMC Plugins FakeSMC HWMonitor Application Network - Intel - Choose latest IntelMausiEthernet USB - Increase Max Port Limit 200 Series Bootloaders - Clover v2.4k r4063 UEFI Boot Mode + Emulated NVRAM Customize Graphics Configuration - AMD Graphics Fixup (required for AMD card!) System Definitions > iMac - iMac18,3 UEFI/BIOS settings After POST beep, press/hold DEL key to enter UEFI/BIOS Save & Exit menu - choose Load Optimized Defaults. MIT > Advanced Frequency Settings > Extreme Memory Profile (X.M.P) - choose Profile 1 BIOS Full Screen LOGO Show - I disable this, but not really required Boot Option Priorities - set this to the UEFI option for your UB flash drive. Disable all other choices. Once we run #####, we’ll come back in here and set to your new boot drive (in my case, the UEFI partition of Samsung 960PRO). CSM Support - Disable. Note that the Storage Boot Option Control option which is set to UEFI (desired setting) disappears along with the other 3 options under CSM Support when you set to Disable. Don’t worry, as Storage Boot Option Control apparently stays set to UEFI “under the hood.” Peripherals Initial Display Output - mobo should auto-detect your GPU card, so this should already show PCIe 1 Slot. You shouldn’t have to do installation using internal GPU, then switch to your GPU card. Peripherals > LEDs in sleep, Hibernation, and Soft Off States: OFF [this is optional if you don't want LEDs on 24/7, even in power-off state). USB Configuration > XHCI Hand-off - set to Enable Note: Once Thunderbolt3 AIC is connected, a new dynamic menu option for configuring the Alpine Ridge card appears below the USB DAC option (which lets you set options for USB charging on the appropriate ports). Chipset VT-D - Disabled Internal Graphics - Disabled (this also turns off the DVMT menu options). Wake on LAN Enable - Disable Power ErP - Enabled [UPDATE 25Mar2018] - This is now required to help fix issue where mobo on-board LEDs do not power off when in sleep/shutdown mode. Soft-Off by PWR-BTTN - I set this to Delay 4 Sec. Save & Exit - Choose Save & Exit Setup - this saves your changes and reboots your system.
×