Jump to content

gwali

Members
  • Content count

    6
  • Joined

  • Last visited

About gwali

  • Rank
    InsanelyMac Protégé
  1. Lenovo T400 2765-TDG

    There are no driver for Intel 4500 (and probably there won't be some either), ATI should be in pipe. There are no Driver for Intel wlan (in fact there is iwidarwin, but thats not working really well). For your ethernet there should be a kext - please search for devicestring.
  2. Weird Pattern on SXGA+ Display and X3100

    Okay, a little update. I succeded in getting it to work with reboot or cold boot - QE/CI and all resolutions setable. Secondary monitor works too and is detected nearly properly (wrong resolution, but can easily be set because correkt resolution is detected). There also QE/CI is fully available. BUT: On Display Sleep or Standby/Hibernate all is set back - my internal monitor is scrambled, the external is still working properly. I again get half of screensize with black lines as before or full screensize with black lines (not really usable). But thats a new failure. So my question - why doesn't sleep aka wakeup doesn't work as expected - is another graphics driver loaded after sleep? From boot on it does work as mentioned. Hope someone kann help me. If anyone needes the driver package i'm using right now, please contact me here. I will then add it. Systeminfo/Searchphrase: Lenovo T61 8897 X3100 SXGA QE/CI working
  3. Hi, I have a little weird problem with my lenovo T61 (Intel X3100, SXGA+ 14' 1400x1050 TFT). MacOSX-dirtibution: iPC 10.5.6 working, no explicit graphicsdriver installed My Intel X3100 is recognized as working - even with CI/QE and resolution change, but on internal display only every second pixel column is shown, between there is a black column. Actually I can see only have of the screen - the other half is out of sight. If i take the menue and the dock to an external display (also works with QE/CI) all is fine - except the internal display which stays scambled. If i take snapshots of the display thorugh a screengraber, it shows no distorsion. If i delete all X3100 kexts i have 1024x768, but no QE/CI working without a scrambled screen, but with a kext (doesn't matter which - also scrambled if QE/CI is not working) the blue screens apperes unscrambled, then blacks out and then adds the black columns. Here a the full specs with externel monitor attached both working in nativ resolution. I've searched for this problem, but didn't found any hint, so i hope someone can figur out my mistake.
  4. IBM aka Lenovo X60 Only 1024x768 4:3, but fully working with DualScreen and QE/CI, does have 4,6 or 9 cell battery, sound and lan working oob. Used or even new ones are incredibly cheat for what you get (really good quality).
  5. QE and OpenGL could be enable upon this card (and even the X31) with Tiger (8MB (original Apple Hardware - Clamshell), 16MB and 32MB incarnations) - but the related packages (Radeon 7500 packet, callisto 006 and agpgart) are not supported by leopard. So i believe there has to be a solution :-) EDIT: Serach for 0x4c59 @ http://wiki.osx86project.org/wiki/index.php/HCL_10.4.8, here is it mentioned
  6. Hi, I'm pretty stuck at the moment with installation of Mac OSX 10.5.2. I got it working and updated to 10.5.5 with Combo-Update (Kernel 9.4.0) but a few problems remaining. 1. Only 512 MB Memory shown by system despite 2048MB available (2x1024MB) 2. No driver support (no kext loaded) for Ati Mobility Radeon M7 3. No Bluetooth for IBM BMDC200 or BMDC300 First some hardware-information: IBM Thinkpad X31 - 1,6 Pentium-M (Banias) IBM-Board with ICH4 Ati Mobility Radeon 7500 (M7) 16MB Vendor: Ati (0x1002) Device-ID: (0x4c59) Revision-ID: (0x0000) VRAM: 128MB (16MB real) Type: Display BUS: PCI (AGP real) Atheros Wifi (Airport Extreme 0x168C, 0x8331) AC97-Audio IBM Bluetooth Module II; IBM Bluetooth Module IIV (BMDC200; BMDC300) Some software-information: Mac OSX 10.5.5 installed through Kalyway 10.5.2 install DVD and updated it with official 10.5.5 Combo Checked Modules in Kalyway: IP80211Family, wifi_Atheros, SSE2_Jas1048_ACPI_APIC, Lastnetkassmbios, TimeMachineFix, Intel Memory Controller options other patches: http://forum.insanelymac.com/index.php?sho...1036&st=500 (fixed bootdelay with PC-Card) http://forum.insanelymac.com/index.php?showtopic=95789 (fixed USB-petction problems) Now the problems encountered: Darwin only boots with 512 MB - MacOSX also doesn't show any more. How can i fix Darwin to show whole system memory? I didn't found any helpfull information, because search after "Darwin 512MB" or "Kalyway 512MB" only shows threads and information (insane and google) about graphic cards with 512MB :-( I didn't found any driver/kext or patch to enable CI/QE and OpenGL in the M7 graphics card. I don't believe QE could be enabled anyway, but CI is software emulated and pretty slow. The only hint i found was in an very old thread dealing with this problem in 10.4.1 (http://forum.insanelymac.com/index.php?showtopic=11134) Also i didn't found any information about the mentioned bluetoothcards. Does anyone know these and could say something about vendor or possible driver? I would be really happy if someone can take me a bit further - especially the first two problems. Bluetooth is not really important. Thanks!
×