Jump to content

Ravenstein

Members
  • Content count

    6
  • Joined

  • Last visited

About Ravenstein

  • Rank
    InsanelyMac Protégé
  1. Ravenstein

    boot1 error after installing Clover!

    Normally I am not so pateint, but let me try this time... :-) Firstly, I think it is a good manner to post your specs at your signature, so that all people can get a closer image of your problem. ps: this thread is a best practice.. In general, it should be a simple problem. If I were you, I would figure out which HDD & which partiton I installed Mavericks. esp. use Installation USB boot up again into Disk Utility and Terminal, using comannd diskutil to identify the 2 points. change according in the command line of : dd if=/usr/standalone/i386/boot1h of=/dev/disk0s2 where disk0 is the 1st HDD, s2 is 2nd partition where your MAcOSx installed. The ultimative solution is google and read, google and read... esp. which installation guide you follow. Good luck.
  2. Ravenstein

    boot1 error after installing Clover!

    http://www.tonymacx86.com/25-boot0-error-official-guide.html
  3. I may have similar issues with HDMI monitor as yours. I boot from SSD, it is extremely fast. External HDMI with HD4k freeze with matrix pixels. When HDMI monitor is off, let MacOS boots first w/ native screen then power on HDMI monitor, both are fine. So I guess it must be the HDMI driver in loading sequence is lower priority(than VGA/DVI), HDMI is not ready yet due to SSD fast booting. But once it warmed up then reboot, the frozen screen issue is gone. On the other side, HD4K(or others) is known have problem with extended screen (esp. after screen unlock even in Windows). You may also check which HDD/SSD your Chameleon boots from, make sure it is same as where your MacOSx installed. Just my 2 cents, don't know if helpful.
  4. Thanks. U r right. Sorry I forgot 802.11 stands for wifi standards... So what does "Unsupported ioctl 181" mean? how to debug further? thx!
  5. Hi Mieze, thanks for your effort. My RTL8105E is running better with your kext 1.0 instead of AppleRTL8169Ethernet 2.0.6. But when I use lan cable, system fan runs crazy and HWsensor report CPU temp > 70C. Using wifi is just fine. Don't know if these relate to your kext. (also I have warning in console, kernel: apple80211Request Unsupported ioctl 181) Just want to report that, do you have a clue? thanks! ------------- Hereby the log from "grep -i realtek /var/log/system.log" localhost kernel[0]: Ethernet [RealtekRTL8100]: Warning: PCIe ASPM enabled. localhost kernel[0]: Ethernet [RealtekRTL8100]: EEE support enabled. localhost kernel[0]: Ethernet [RealtekRTL8100]: TCP/IPv4 segmentation offload enabled. localhost kernel[0]: Ethernet [RealtekRTL8100]: TCP/IPv6 checksum offload enabled. localhost kernel[0]: Ethernet [RealtekRTL8100]: Using interrupt mitigate value 0x0. localhost kernel[0]: Ethernet [RealtekRTL8100]: RTL8105E: (Chipset 12) at 0xffffff807aaa5000, 8:9e: 1:35:d5:5c myMachine kernel[0]: Ethernet [RealtekRTL8100]: Link up on en0, 100-Megabit, Full-duplex, No flow-control myMachine kernel[0]: Ethernet [RealtekRTL8100]: Link down on en0
  6. I get this constantly in console, anyone knows what is "apple80211" for ? or what does it mean? Running 10.9.2, FakeSMC v.6..8.1307 installed, AR9285+AR3011. also If I connect LAN cable (without wifi), fan rans crazy, HWmonitor(v.6.8.1307) report CPU temp >70C. But with wifi is fine. (LAN card: RTL8100.kext v.1.0 installed) Could anyone explain/help. thanks!
×