Jump to content

brookheather

Just Joined
  • Content Count

    9
  • Joined

  • Last visited

About brookheather

  • Rank
    InsanelyMac Protégé

Recent Profile Visitors

286 profile views
  1. I have an AzureWave AW-CE123H and can connect a Logitech K380 Bluetooth keyboard fine however my two Logitech mice do not connect - they appear in the Bluetooth list but pressing connect doesn't work - just tries connecting for a minute and then reverts back to Connect. I have the MX Master and MX Anywhere 2 mice - they connect fine to my MacBook Pro which also has Catalina installed.
  2. Files attached. USBPorts.kext.zip SSDT-EC.aml
  3. I updated my 800 G1 USDT to OSX 10.15 Catalina yesterday - the upgrade itself went fine and afterwards I updated the various kexts to the latest versions. My wireless card however is no longer working - it is an AzureWave AW-CE123H which is a Broadcom BCM94352HMB. I had it working on Mojave by running the installer from here: https://www.insanelymac.com/forum/files/file/844-azurewave-aw-ce123h/ After updating to Catalina the wireless seemed to work intermittently and the boot took a lot longer than usual and my PC kept locking up or restarting so I removed the various kexts it installed. So my install now boots fine but of course no wireless - currently using the Intel Ethernet which works. Is there any way to get this wireless card working in Catalina? One of the problems was the installer tries to put the kexts in S/L/E which is now read-only in Catalina - I did try installing them in L/E but the card doesn't seem to be recognised. I also have the problem with the USB3 ports not working - the two at the front don't work and only one of the rear USB3 ports works. I have the USBInjectAll.kext installed - should I try the USBMap.kext linked to above? UPDATE: I used the Hackintool program and mapped all of the USB2 and USB3 ports - I then exported the USBPorts.kext and SSDT-EC.aml files - all of my USB2 and USB3 ports are now working. UPDATE2: Now got the wifi and BT working - installed the latest AirportBrcmFixup.kext for the wifi and found a Catalina version of BrcmPatchRAM3-V2.3.0d2.zip which seems to work as well. https://www.insanelymac.com/forum/topic/339175-brcmpatchram2-for-1015-catalina-broadcom-bluetooth-firmware-upload/?page=6
  4. Do you have a 6-pin PCIe power plug on your PSU - if not you would need an RX560 I think.
  5. I have not been able to boot my HP 800 G1 USDT when connected to my Dell 4K monitor via DisplayPort - it will restart while booting. If I boot with the DP cable disconnected and then connect the cable it will only display at 2560x1440@60Hz. You can use a GTX1050 with High Sierra to display 4K but bear in mind there are no Nvidia web drivers for 10.14 Mojave. If you want to use 10.14 then you would be better off with a supported AMD card.
  6. So I now have OSX 10.14 Mojave running on my HP 800 G1 USDT. I had a few issues during the installation. I first updated Clover and the drivers to the latest version (including APFSLoader and AptioMemoryFix). I then ran the Mojave installation which took about half an hour. During the final step I get a Boot 0af error when booting - this was solved by taking out the SSD and re-installing Clover with the option to install on the EFI partition (then copy the config.plist and kexts from the old Clover install) - the drive was changed to APFS and this probably removed the previously working HFS+ boot. I then had an issue where I would get the Apple logo and the bar would fill slowly to the right and then the screen went blank. Running in verbose mode showed an issue with a timeout for AppleACPICPU. I took the SSD out again and copied the latest kext files to the EFI partition - in particular there were new versions of FakeSMC, Lilu and IntelGraphicsFixup. With these changes it now boots into Mojave fine. Sleep works fine but you will need to reapply the "pmset" fix in the opening post.
  7. Should be fine - I have it working on 800 G1 USDT and SFF - the tower uses pretty much the same motherboard as the SFF. I also have it working on the HP ProDesk 400 G2 Tower PC.
  8. Thanks that works fine for my i3-4150 HD4400. I upgraded my existing install from 10.10.5 to 10.13.4 - initially I panicked when Clover didn't find any bootable drives after upgrading but I just needed to install the driver for APFS (apfs.efi) and then it all worked fine.
  9. I've changed from an i5-4590 to an i3-4150 and now get a blank screen on boot - I assume I need to change the IntelGFX config to some other value for the HD4400 graphics?
×