Leaderboard
Popular Content
Showing content with the highest reputation on 03/08/2021 in all areas
-
Hackintool 3.5.3 reports correct 0.6.7 version for me... When I "upgrade" from one version of OC to the next, I completely clear my EFI, copy the new (in this case 0.6.7) EFI from github (both BOOT and OC) to my clean EFI and then replace config.plist, Kexts, ACPI. Then I reboot, clear NVRAM and boot with my new OC. Without seeing your EFI, I'd guess that you've accidentally mixed OC file versions in your EFI or you're not booting from the EFI that you think you are.
2 points -
It didn't give me any peace after all. I did everything all over again. Downloaded OpenCorePkg-master, had it compiled, created a fresh config.plist from a sample.plist, did an clean-NVRAM, reset the Linux boot entries in the shell, and so on. The result this time is a working configuration, as it should be. Now I just need to find the error that caused it to fail before, but at the moment I can't see the wood for the trees. Thank you very much for your help, it has motivated me.
2 points -
if you want to compare it with mine 0.6.7-config.plist.zip2 points
-
Version 1.0.0
6,186 downloads
Modified IO80211Family.kext especially who use device based on Atheros40 (the idea came from CtlnaAHCIPort.kext) so we don't need to touch /S/L/E just inject via OpenCore, and we can running Big SUr without open Sealed (no need remove/delete vanilla IO80211Family.kext in /S/L/E) I'm not try in Mojave or Catalina but I'm sure is worked too 1. just put 2 kext HS80211Family.kext & AirPortAtheros40.kext .../OC/Kexts and make sure inject via config.plist do not inject IO80211NetBooter in the plist (must do research so i leave there in plugin), I remove IO80211NetBooter from plugin so as not to confuse see my pict below just add 2 value 2. you can add value manually VendorID in IONameMatch (atheros40) if your ID not present 3. refer to @MaLd0n guide in olarila for working Wifi Atheros AR9565, AR9462, AR9463, AR9485 here is the modification (no need injector) AR9565 AirPortAtheros40-9565.kext.zip AR9462 AirPortAtheros40-9462.kext.zip AR9463 AirPortAtheros40-9463.kext.zip AR9485 AirPortAtheros40-9485.kext.zip Additional : Fake Locale & Country Code Use this kext WifiLocFix.kext.zip to fix Locale & Country Code (Fake AirPort Location Interface) You can change it inside WifiLocFix.ket depend on your location and don't forget to inject in your config.plist Card Type: AirPort Extreme (0x168C, 0x3112) Firmware Version: Atheros 9380: 4.0.74.0-P2P MAC Address: XXXXXXXXXXXXXX Locale: ETSI Country Code: ID Supported PHY Modes: 802.11 a/b/g/n Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64 Wake On Wireless: Supported Status: Connected1 point -
Since these posts show updates, I am looking for some pointers as to why updates are not showing in Big Sur system preferences. Csrutil enable and csrutil authenticated-root enable in recovery console modifies NVRAM csr-active-config in config.plist to 10000000 and booting is enabled but no updates. Cannot boot Big Sur with SIP completely enabled 00000000 in config.plist due to kernel panic. Any specific pointers as to where and what to look for with boot args set to: no_compat_check keepsyms=1 -lilubetaall -v debug=0x100 lapic_dont_panic=1 What specific log files to look at? What specific boot files to look at?1 point
-
Glad to read you. Sometimes there are strange things in this hackintosh world.1 point
-
@MacKonsti I haven't performed a "from scratch" OC install (all of my installs are migrations from CLOVER), so I haven't had to generate a new ROM value. For new ROM value, you should be able to use the same method that works for CLOVER: use a network MAC Addr. See here.1 point
-
@antuneddu I took the settings from your config.plist and activated my custom entries. The result is the same: Windows can be booted, but the two penguins cannot. As soon as I go back to 0.6.5, everything works again. I give up. Maybe it will work again in 0.6.8 or later.1 point
-
Yes, I see. Your LAN card is Intel and Clover has algo to catch its MAC-address by two ways. First one using UEFI BIOS. But in your case UEFI BIOS does not supply services for reading MAC. Second one is legacy way developed for very old cards. It seems for your case the procedure is no more working. So write into config digits you know <key>ROM</key> <data>112233445566</data> It may be <string> as well.1 point
-
20210308 * New: All data tables support copying rows and pasting rows between multiple processes or single processes (multiple rows, undo and redo are supported, copied history data is stored using persistent storage policy, if pasting history data is not supported, the paste menu is grayed out) * Other detailed improvements and optimizations1 point
-
maybe c enters the scanpolicy? I set it to 2687747 and it works
1 point -
Reboot and clean NvRAM, see what the result is.1 point
-
but i'm not as good as you or @blackosx for icons i don't know where to start, all the way i'm trying but for now i use your icons they look good on top hope you don't mind, i'll pay you the copyrights .I wonder if you can move the position of the icons upwards, perhaps by modifying the .lbl files? Thanks
1 point -
it's working perfectly thank you again for all your intelligence
1 point
