rayap
Members-
Posts
163 -
Joined
-
Last visited
Reputation
15 GoodProfile Information
-
Gender
Male
Contact Methods
-
Website URL
http://
-
Rolled back to 10.10.5 AMD* and IOAcc*, sleep/wake works.
- 585 replies
-
Looks like Tahiti and Pitcairn cards are not affected as these are supported by Apple. They don't need the cail_properties tweak either.
- 585 replies
-
@themonarc, 'unless you have a apple wireless card'. Using the BCM94360CD address as ROM, appears to log in to iMessage but within seconds deactivates. Any ideas plse?
-
Have a 2 for x in an early 2011 MBP.
-
Works perfectly when fully up. Problems are not powered up on warm start following shutdown, ok on cold start. Also not up on wake from sleep, need restart. Presently testing on a DS4P board. Edit: Problem overcome in PCI-E x4 slot.
- 107 replies
-
Move it to E/E.
- 35 replies
-
- applertc
- cmos reset
-
(and 2 more)
Tagged with:
-
Power management for Sandy/Ivy Bridge/Haswell CPUs
rayap replied to Pimentel's topic in Tutorials (The Genius Bar)
DPCIManager p-states not working after update to 10.9.2, fine before.- 532 replies
-
@Vlada. Thank you for the rom file. This new card is in my wish list hence my interest. In the meanwhile have been fiddling the frame buffers for my HD7770 trying to get two displays going. Found Dashimaki most suitable. as the sense ids (from radeon_bios_decode) are closely related. However after many futile attempts now settled with one display on the hdmi connector cos using hdmi audio. Everything works fine with this setup. Even with the DisplayPort nearly all is well, but cannot wake up from sleep - something about pin 20 and the DP-DP cable. And, in my case without DSDT injection, the DVI connector works well with Buri and GE on. With the default Radeon FB both displays work but again wake from sleep failure. You may want to rearrange your preferred frame buffers similar to the personalities when the default frame buffers is loaded. If you only used the DVI connection arrange to load it @0, or @1 similar to the default RadeonFB. (i.e. rearrange the port hierarchy). This may overcome your black screen but need check wake from sleep. Best of luck.
-
Maybe dumps using ati-personality-pl or Redsock BIOS decoder too? http://rampagedev.wordpress.com/kext-editing/editing-atiamd-framebuffer-personality/ Edit: And, system profile when with the default RadeonFB.
-
Any personality dumps for the card?
-
Mac HFS Drive getting damaged sooo easily!
rayap replied to Bandes's topic in OSx86 10.9 (Mavericks)
Recently went thro a patch of similar disk corruption on my old setup P45-DS4P with Mavericks. With Mountain Lion there was no such problems.. Seems to have been resolved after yanking out 800MHz Ram pair and leaving 1066MHz pair only.. Problems started when joint pairs were clocked at 800 but not at 667. -
Jo, I have same board and processor and mavericks is working well. Everything you need to know is within this forum.not sure about any particular guide. If you cannot connect the ssd to your MacBook, use two USBs, one for Clover and other - 8G - for the OS, created by the createinstallmedia method. This should get you going.
-
Found it useful. Auto-sleep somehow not working on Haswell setup. so this is handy. Need to check over prolonged downloads or movie/music runs. Thanks. Edit : Resolved auto-sleep with proper SMBIOS.
-
IS HWMonitor behaving normally. Not getting any CPU related temp or freq figures. Mostly "0". Edit: OK after reinstall HWSensors package.
-
Intel HD4000 and Haswell Inject AAPL,ig-platform-id
rayap replied to Micky1979's topic in Front Page News and Rumors
@Picasso Two discrete graphic cards in addition to the integrated graphics, tried it once before on my trial setup. After fumbling along now in better shape with integrated graphics and the only AMD card. Still sorting out the HDAU situation.