Jump to content
Welcome to InsanelyMac Forum

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

72 posts in this topic

Recommended Posts


Have you installed the aDummyHDA.kext properly (you should take it from post 19)? You must use something like KextWizard

 Nope, I'll try it today!



I warn you that in these days I have some exams at the university so it'll take some time for me to patch them. Maybe a couple of days.


I wish you good luck, man! Get not "Excellent" but "Amazing" marks!)))) If it needs you can tell your professors that micsha called you worldwide man!

Share this post

Link to post
Share on other sites

So, yeah, I've installed aDummyHDA.kext through the Kext Utility, but there's no affect - it's color is grey and that's is all.


My Origin folder (after F4) in attach.


Don't understand about EDID - now monitor works perfectly, my resolution is 1366x768.




Share this post

Link to post
Share on other sites

Only to be sure....you didn't touch the original AppleHDA.kext, did you?

I mean, after installing El Capitan you didn't try to install the AppleHDA maybe? Because it would be wrong.

If you touched the AppleHDA it won't work because you need the original AppleHDA.kext... So if you "overwrote" or modified in any way the original AppleHDA you must restore the original.

If you did the backup of it you can reinstall it always with KextWizard, otherwise if you don't have the backup of the original you have to reinstall the whole OSX system...


So basically you have:

Original AppleHDA+aDummyHDA.kext+Config.plist injection



Can you upload the config.plist version that you are using please? So that I'll check if the injection is correct...

Maybe also the dsdt.aml in efi\clover\acpi\patched that you are using. You can compress them in a zip.



If this won't work you can try "returning" to the patched AppleHDA method...

Share this post

Link to post
Share on other sites

No, it is ok if you don't have any AppleHDA.kext in Clover's USB flash drive. The AppleHDA.kext is installed in the system directly by OS X. I was only saying that if you, by any chance, modified it, you must restore the original version, because you need the original AppleHDA to make aDummyHDA work. I don't know, maybe you tried for instance to install a different "AppleHDA" maybe from post 1 or 34 or other, than it is normal that it is not working because you modified the system's AppleHDA.

So I'll assume that you didn't touch the AppleHDA and you didn't overwrite it, otherwise this will be useless...


Try this config.plist instead of yours, as it was before it was wrong because it hadn't the audio layout injection.



Besides...after the installation of aDummyHDA.kext, did you repaired disk permissions and kext caches in KextWizard as shown in the picture below?




PS: be aware that you are using Anerik's memory settings for 14 GB of RAM with 1333Mhz frequency with "Trust" mode enabled too....if you should have any memory error it could be one of the causes unless your machine is exactly like his...



PPS: Moreover I don't understand which dsdt you are using......Mine or Anerik's? You were using Anerik's config.plist so I guess you are using also his DSDT, isn't it? If you post it we can be sure about this too...Post the EFI\CLOVER\ACPI\"patched" folder in a zip, it contains both dsdt and ssdt.

Which processor (CPU) do you have? I7-2630QM or I7-2670QM? I guess the 2670QM is it right?



Share this post

Link to post
Share on other sites



Oops, nope - I have Intel i3-2350M 2300Mg (Mac shows CPU right way), RAM is about two cards for 4Gbs (don't know, how MacOS counts RAM size - free or all) and HDD 500Gb.


I used anerik's files for ACPI, kexts and config.plist.


There's my EFI folder - https://www.dropbox.com/s/rleo2lsom22035i/EFI.zip?dl=0 .


P.S.: I will reinstall Mac after getting your files - it's not so long but for sure that it will be reliable to work with mac))


P.P.S.: Man, if it is not so hard, could you send me articles or other texts, which helped you to manipulate with DSDT, config,plist and so on? In PM).
Just because I want to know how to do it - and if I will need it in the future, I'll do it by myself. It's the lucky time, that I met you here - without you it I'm not sure that I installed MacOS))).

And I think, it's the best time to read and ask you why things have to be the way they are)).

Share this post

Link to post
Share on other sites

Unfortunately today I don't have much time (exams...), meanwhile try replacing your config.plist and dsdt with the ones attached.

According to me, if you have original untouched AppleHDA, if you have installed the aDummyHDA that you have among the kexts in Clover with Kext Wizard, if you repaired the disk permissions and rebuilt kext caches with Kext Wizard as shown in the post above, with this files you should have working audio.



1) Install aDummyHDA in your system with kext wizard as shown in the picture below (Click "browse", select the aDummyHDA in your EFI\CLOVER\Kext\Other and Click "Install")

2) In Kext Wizard repair disk permissions and kext caches as shown in the picture in the post above.

3) Delete the aDummyHDA.kext from EFI\CLOVER\Kext\Other (save its somewhere else if you want, but remove from the Clover usb)

4) Replace your config.plist in EFI\Clover with the one attached in this post

5) Replace your dsdt.aml in EFI\CLOVER\ACPI\patched with the one attached in this post.

6) Reboot


According to me you should at least see the volume icon as "black" working icon. If it is the case we are "near" the solution...


As soon as I have some time I will send you the guide I followed, but trust me, in this case even though the files maybe are not perfect you should have audio working. According to me you should work to have also the audio working now, when you have it you can really patch your files and reinstall the system clean, but right now the not perfect ACPI files won't make the difference in the audio (except for the injection of audio layout but I fixed it....). The wrong CPU and RAM won't break audio, even because however are have the same "series" (Sandy Bridge) of processor, so it is not as bad as it seems, because probably the power management is almost the same, in fact they are however working....



If the audio doesn't work again after the process above with the files I attached I'll have two other things to try.... 

Can you tell which version of El Capitan you are using? 10.11.3? 10.11.2? Because I can send you the original AppleHDA for them if you maybe have modified it....


As soon as I have time I look for the guide I followed and pm it to you!

New config.plist.zip



Share this post

Link to post
Share on other sites

jackal992, one more question:

If I reinstall MacOS by using Clover flash drive with changed to yours config.plist and DSDT - will it be OK?

Share this post

Link to post
Share on other sites

Unfortunately I don't know.

According to me you should have working audio also if you don't reinstall the system. When you understand which is the file that does the trick of enabling the audio of course you can "clean" everything by reinstalling OSX.

After the last update to 10.11.3 I had some difficulties in enabling the audio too...

Share this post

Link to post
Share on other sites

Yeah, it could be used for installation! Sometimes it's reboot itself (maybe error or smth else - I don't know) on loading, but then works without any problems). I tried to install MAcOS 2-3 times - finished successfully! Good job!


Your second config (post#57) better than first (post #55)  - VGA much better, in #55 I felt frequecy of monitor light, second is quite smooth, but quality of picture a lil' bit worse than in Windows. Small photos like a lil' bit smashed. But ok, it's not the main point - we can return later.


Thanks for fixing size of RAM!


About sound - nope, it's grey. 
I also tried VooDooHDA - OMG))). I get sound but Voodoo has linked imput from mic and output - and my ears were bleedin')). Unfortunatelly, I didn't found how can I switch off mic sound.


P.S.: I'll try one more way just to check, have I missed smth.

Share this post

Link to post
Share on other sites

Ok, even though it seems a bit strange to me that nothing works, we can try one last thing, i.e. revert to the "original" audio patching, that is directly patch the AppleHDA without using the aDummyHDA.


I have patched the AppleHDA as if you were using El Capitan 10.11.3...is this correct? Are you using 10.11.3?


I prepared 4 versions of the files that must work together as a "pack".


Before doing so you must remove the aDummyHDA both from Clover usb (delete from EFI\CLOVER\Kext\Others the aDummyHDA if you still have it) and from the system. To remove from the system you have to browse to "system/library/extensions" (you can go in Finder->Go->Go to Folder or Alt+Shift+G and type "system/library/extensions") and delete the "aDummyHDA".


Once you do this you try "pack 1" here attached:

-install AppleHDA with Kext Wizard (this time when you install enable the option "Backup kexts that will be replaced"

-In Kext Wizard repair disk permissions and rebuilt kext caches as usual

-try using the pack 1 dsdt and config.plist in your Clover usb (the dsdt in ....ACPI\patched) and reboot


If this doesn't work try pack 2:

-try using the pack 2 dsdt and config.plist in your Clover usb (the dsdt in ....ACPI\patched) and reboot


If this doesn't work try pack 3:

-try using the pack 3 dsdt and config.plist in your Clover usb (the dsdt in ....ACPI\patched) and reboot

If this doesn't work try pack 4:
-Install HDAenabler3.kext with KextWizard as usual
-In Kext Wizard repair disk permissions and rebuilt kext caches as usual

-try using the pack 4 dsdt and config.plist in your Clover usb (the dsdt in ....ACPI\patched) and reboot

To be very fair with you after this tests I don't have any other idea, if it still doesn't work you can try ask Anerik for his help, even though I managed to make his aDummyHDA work with my machine that is different, so it's strange that for you it doesn't work..





Share this post

Link to post
Share on other sites

jackal992, first pack was the right one!!! Sound and mic work perfectly!!


Thank you!))


So, my final EFI partition here: https://www.dropbox.com/s/6n1cqi33u4mz1iq/EFI_2.zip?dl=0(use it with jackal992's  AppleHDA from pack #1 in previous post!)

The only question I left is to install bootloader on hdd - just to free my usb flash))). But I think I will find a way!


P.S.: If you have twitter - you can write it in PM, I'll make public appreciation)))

Share this post

Link to post
Share on other sites

Wow glad to hear that!


For the installation on HDD I don't really know because as I explained to you I made a small partition in fat32 on my hdd where I copied my Clover USB files and I boot from that partition always from the EFI shell, so manually. I chose this way so that Windows boot loader remains the main one and I don't risk breaking it.


If you want to install it so that it starts when you boot the machine I think you have to install some scripts, I read in a guide by RehabMan:

-Installing to the HDD/SSD after installation is very similar to installing to the USB.

-You change the destination of Clover's installation to your target disk

Notes on HDD install:

- you might want "EmuVariableUefi-64.efi", but it would depend on whether native NVRAM works for you

- select "Install RC scripts on target volume" and/or "Install all RC scripts on all other boot volumes"

- selecting "Install Clover Preference Pane" is optional

- there are also some "Optional RC Scripts" you might want to read about


but again I didn't do that so I don't know...of course after the installation of Clover you copy in the "new" Clover's EFI folder the kexts, the acpi patched files and config.plist that work for you.

Share this post

Link to post
Share on other sites

I chose this way so that Windows boot loader remains the main one and I don't risk breaking it.



Yeah, I know it))). I broke two Windows bootloader (the second I repaired, but that's enough) - I don't want to play with it too)))).


I gonna go your way!

Share this post

Link to post
Share on other sites

Hi, jackal992!

I have two questions (maybe you can help):

1) Strange issue, but not all FNbuttons works)). Is it normal?

I can switch off screen, but can not change brightness or bump up or down volume.

2) About sound). When I close my notebook, MacOS works, but sound disappear - and only rebooting can return it. Do you have so?


Thanks in advance!

1) I have all the FN keys working. I used the attached kext: "AsusNBFnKeys". You can try to install it with KextWizard and repair permissions and caches as usual.

(Assuming that your brightness works properly, you can try that by going in SystemPreferences\Display and move the slider)


2) I don't have the problem of sound not working after sleep, but you can try to solve it with CodecCommander. Unfortunately I cannot help you with this, I didn't do it!

However here are some useful links:

Guide: https://bitbucket.org/RehabMan/os-x-eapd-codec-commander/overview

Download: https://bitbucket.org/RehabMan/os-x-eapd-codec-commander/downloads


There should already be a profile for the ALC269. You can try that...



Share this post

Link to post
Share on other sites

USB3 works now, seemed to be a reboot issue. Ethernet is working fine as well, thanks a lot! :) Is there any way to turn off Bluetooth (my button is greyed out)?



i just noticed my bluetooth button is also grayed out.

has any one found a way to correct this ?


i notice that on my EFI\CLOVER\OEM\N53SV\KEXT\OTHER\

I have BTFirmwareUploader

am wondering if thats the Bluetooth kext that the machine is using and causing my bluetooth issue.


if i remove the kext or replace it,

do i have to use disktools to fix permissions (or another tool) on the EFI partition, or can i just remove it and reboot ?



Share this post

Link to post
Share on other sites


i just noticed my bluetooth button is also grayed out.

has any one found a way to correct this ?


i notice that on my EFI\CLOVER\OEM\N53SV\KEXT\OTHER\

I have BTFirmwareUploader

am wondering if thats the Bluetooth kext that the machine is using and causing my bluetooth issue.


if i remove the kext or replace it,

do i have to use disktools to fix permissions (or another tool) on the EFI partition, or can i just remove it and reboot ?




I use the attached kext to make bluetooth work and my icon is not gray but black. I don't have the "BTFirmwareUploader".

If you install/uninstall kexts from s/l/e I think it won't hurt if you rebuild disk permissions and kext caches, on the contrary many time is needed...


Share this post

Link to post
Share on other sites

hello jackal! Thanks for your precious help!

i tried to install everything from scratch from one of the latest versions of el capitan, and it doesn't work anymore.

May you please provide both your config.plist configuration for (latest) el capitan and files provided in the EFI folder?




EDIT : fighting with clover it seems to work again but it's very unstable, compared to chameleon and old good osx versions...


PS: Is there anyone that is using clover and snow leopard ?  may you please send me some directions to have snow leopard working with clover? Thanks a lot!! i know it's a bit off topic ... sorry for that

Share this post

Link to post
Share on other sites

Hi, i am new to this forum! 

I own a great old N53S and i would like to know if there is any way to install latest Sierra or latest ElCapitan on this great notebook!

Thank you.

EDIT: Any update for n53sm? Sierra? High Sierra? it is a great laptop! thanks!

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By glasgood

      ASUS  STRIX Z370-G ROG
      ( Micro-ATX )
      ** UPDATE  5th Jan 2018  /  Clover v2.4k r4359 **
      Great YouTube Hackintosh Installation Guide from >> Roberto Jorge <<  based on this post.
      Asus ROG Strix Z370-G Gaming (Wi-Fi AC) ( Micro ATX )  i7 8700 3.2GHz  Corsair Vengeance LPX 8GB (1 x 8GB) DDR4 DRAM 2400MHz (PC4-19200) C14 Memory Kit - Black  Samsung Evo 960 250GB NVMe SSD  NVIDIA GeForce GTX 1080ti (or a GTX 1050 / 1060 / 1070 will work  ) ABWB 802.11AC WI-FI with Bluetooth 4.0 PCI-Express  BitFenix Phenom – Tower – micro ATX  Noctua NH-L9x65 - NH-L9x65 Low Profile Performance CPU Cooler  EVGA SuperNOVA 750 G3, 80 Plus Gold 750W  Corsair UK K65 Rapidfire Cherry MX Speed Performance Multi-Colour RGB Backlit 10 Keyless  Samsung 850 EVO 500GB  Dell UltraSharp U2717D (2560x1440DP) IPS LED 27-Inch Infinity Edge  
      Wi-Fi ( Onboard WiFi card was replaced, see components list above )   Bluetooth Ethernet Port Sound --> Nvidia HDMI Audio and Realtek Audio NVMe 960 EVO / Trim Nvidia GTX 1080ti i7-8700 ( six-physical cores and 6 virtual - HT ) Intel UHD630 (configured with DisplayPort attached to Asus board) 8. Sleep Power Management and P-States         USB 3.0 USB 2.0 HandOff AirDrop iMessages iCloud Hardware Acceleration AirPlay iBooks Personal Hotspot  

       F2 to enter BIOS on Asus Z370 Strix 2 - Switch to Advanced Mode F7  

      Some of the settings already preset, ensure you have the following BIOS settings:
      Exit → Load Optimized Defaults : Yes Advanced \ System Agent(SA) Configuration → Vt-d : Disabled Advanced \ PCH Configuration → IOAPIC 24-119 Entries : Enabled Advanced \ APM Configuration → Power On By PCI-E/PCI : Disabled Advanced \ Network Stack Configuration → Network Stack : Disabled Advanced \ USB Configuration → Legacy USB Support : Auto ( needs to be auto for SSDT-UIAC.aml to work ) Boot → Fast Boot : Disabled Boot → Secure Boot → OS Type : Other OS Boot → CSM : Disabled ( Only enable if using dual monitor setup) Ai Tweaker → Asus MultiCore Enhancement: Disable ( but only if you have intel stock CPU cooler ! )  
      See spoiler for BIOS Screenshots.
      Advanced \ System Agent(SA) Configuration → Primary Display : Auto Advanced \ System Agent(SA) Configuration → iGPU Multi-Monitor : Enabled OR
      Integrated Graphics : Enabled iGPU MultiMonitor : Enabled DVMT Pre-Allocated : 128Mb 4. Primary Display : Auto  
      When running the installer the memory modules must be inserted in motherboard slots A1 and A2, otherwise you will be unable to run the installer.

      Download High Sierra from the Apple App Store  
      Prepare USB Flash Storage Pen

      Insert USB Storage Launchpad / Other → Disk Utility Choose your Flash Storage Pen from left panel Click Erase Settings: Name: USB Format: Mac OS Extended (Journaled) Scheme: GUID Partition Map Click Erase
      Create  macOS High Sierra Installer

      Launchpad / Other → Teminal Copy and Paste into Terminal:  sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/createinstallmedia --applicationpath /Applications/Install\ macOS\ High\ Sierra.app  --volume /Volumes/USB/ Press: Enter Enter password: Type: Y Press: Enter Done!   

      You have now created the macOS High Sierra Installer. In order to boot and install macOS onto your computer the installer requires the Clover boot loader from Clover team.
      The Clover boot loader contains, a configuration file ( config.plist) and kernal extensions (kexts), the config.plist and kexts are specific for each Hackintosh desktop / laptop computer build. Clover boot loader also has many other files and folders. 
      I have already prepared a USB drive using the Clover installer  and made edits to config.plist for this build, you can download and copy over my EFI  Folder and skip steps in Spoiler below,  then paste the downloaded EFI folder in the hidden USB EFI / ESP partition on your High Sierra USB installer drive. 
      See the spoiler, using Clover installer to make High Sierra USB installer bootable.
      View the hidden macOS High Sierra Installer's EFI/ESP partition 
      Open Terminal Copy and Paste into Terminal:  diskutil list Enter
      Mount the USB EFI / ESP Partition onto the Desktop

      Again, from Terminal. Copy and Paste into Terminal: 
        diskutil mount disk3s1 ** Identify your EFI partition from diskutil list command, in the example image above my external  USB EFI is listed as disk3s, yours maybe different ** 3.  Enter.
      The hidden EFI / ESP partition is now mounted on your desktop.

      Copy EFI Folder to USB EFI / ESP Partition
      ( Don't use the post install EFI folder at top of page, use post install EFI only after macOS High Sierra is installed ) 
           1.   Download the PRE INSTALL  EFI Folder here >> EFI.zip

            2.  Drag & Drop or Copy & Paste downloaded EFI folder into the mounted USB EFI / ESP partition.

      The bootable USB installer for macOS High Sierra is ready to use!
      Insert  the macOS High Sierra USB Installer into computer USB port. Start PC and immediately press keyboard F8. From Asus Boot Menu, choose your USB thumb drive.
           4.  Clover boot menu 
          5.  Choose - Boot OS X install from Install macOS High Sierra..

      Later in the guide, I will explain how to remove the extra entries on the boot menu, so you would have just High Sierra Icon and / or Windows. The extra entries are removed in config.plist in the uploaded EFI / Clover folder that I have provided.
           6.  Wait few mins!

            7.  Choose Languge

            8.  Select Disk Utility

           9.  From Disk Utility Menu --> View / Show All Devices

          10.  If Samsung 960 EVO drive is not visible in Disk Utility, follow these steps inside spoiler below. 
         11.  Erase, disk. Give Name / Format: Mac OS Extended ( Journaled) / Scheme: GUID Partition Map

          12.  Partition, Format: APFS and apply 


          13.  From macOS Utilities screen select Install macOS

          14.  Continue 
          15.  Agree

          16.  Select Drive Macintosh or whatever you named it.

          17.  macOS is now installing

          18.  Wait...
          19.  Success !
      So far, you are using the macOS High Sierra USB installer to boot High Sierra. The USB installer EFI /ESP partition contains the downloaded EFI / Clover folder allowing you to boot to High Sierra desktop.  So at this moment you can only boot High Sierra with the help of Clover on the USB installers hidden EFI / ESP partition.  Next, steps is to make High Sierra boot without the need of the USB installer.
      Copy POST EFI folder to your High Sierra EFI / ESP Partition on your drive
      When you created the USB High Sierra installer, you mounted the EFI / ESP partition and copied over the EFI folder that I provided for the Asus  Z370-G.
      Next, mount the hidden EFI/ESP partition on your High Sierra system drive.
      Then copy the >> or POST EFI folder to your macOS High Sierra system drive . To do this, follow steps below.

          1.  Identify discs to Mount with Terminal command:
      diskutil list
      ** Your disk IDENTIFIER may be different, the images are examples from my system **
          2.   Terminal command below to Mount macOS EFI/ESP partition:
      diskutil mount disk0s1     3.   System drive, EFI / ESP partition is mounted on desktop
          4.   Drag & Drop OR Copy & Paste EFI / ESP folder from EFI - POST-INSTALL   over to EFI / ESP drive partition:

          5.   Done!
      You can now boot and use macOS High Sierra on your computer without the need for the USB device 
      Mostly everything should now be working if you used the same hardware that I listed in parts.
      In the rest of this guide will explain some basic troubleshooting steps, how install NVIDIA web drivers, how sound was installed.. etc.
           1.   You need to mount the EFI / ESP partition to edit the Clover config.plist.
      Previously, the guide used teminal commands diskutil list and diskutil mount to mount hidden EFI/ESP partitions.
      This guide will now use an app to mount the EFI / ESP partition.

      Download @Micky1979 >>ESP Mounter Pro on InsanelyMac and use it to mount the EFI / ESP partitions so that you can view, make edits to config.plist, add extra kexts if needed etc.

      A quick peak at the EFI / Clover contents, highlighting most common files and folders.

          2.   Download >> Clover Configurator  from mackie100, it is used to edit and make changes to config.plist.     

      Open mounted EFI partition, navigate to EFI / Clover, make a copy of config.plist and rename it config.BAK.
      Then drag and drop conf.plist onto desktop. Make changes, save and drag & drop back inside EFI partition.

      Clover Configurator default screen, always save before quitting Clover Configurator!

      Some people will be very familiar with how to find and configure config.plist, I'm listing this guide with extra steps for those new to Hackintosh.
      You might make changes to config.plist with Clover Configurator or add kexts and then discover that you can no longer reach High Sierra desktop or boot.
      The USB installer can be used to boot your Hackintosh ( I mentioned it was a handy troubleshooting tool ). The USB installers Clover boot loader can boot your computer to the High Sierra desktop. You can then mount the EFI/ESP partition and undo config.plist  edits or delete last added kexts that have prevented you from booting to your High Sierra Desktop or just replace the whole EFI folder on your computer with the EFI folder from the USB installer.
      If the above troubleshooting was unsuccessful and you still can't boot your Hackintosh.
      From the Clover boot  screen, enter Clover options:
      Select Boot macOS from Macintosh  Then press spacebar Check: Verobse (-v) Return Enter  
      The Verbose (-v) option will point to where in the startup process your Hackintosh stops, it's also worth checking BIOS settings before starting any troubleshooting. 
      You can then search in the InsaneleyMac forums for a solution, or ask other members. 

      Sometimes when troubleshooting or installing kexts, you may have to disable Apple System Integrity Protection ( SIP ). 
      To disable or enable SIP, mount the EFI / ESP partiton using ESP Mounter Pro or Terminal then edit config.plist with the Clover Configurator.
      Example: Disable SIP in Clover Configurator:

      Rt Variables / CsrActiveConfig --> Enter: 0x67  Partially disable: Rt Variables / CsrActiveConfig --> Enter: 0x3 ( Clover Default )  Enable: Rt Variables / CsrActiveConfig --> Enter: 0x0  
      Clover adds extra MacOS and Windows entries on the Clover boot menu. Below is what my Clover menu initially looked like after installing Mac OS High Sierra and adding a Windows drive to my build.
      The High Sierra Clover theme is from >> hirakujira

      I wanted the Clover boot menu to just show Mac OS High Sierra and Windows.
      Remove extra entries using Clover Configurator
      Add the Preboot string to config.plist    ( Removes Apple Preboot entries ) Add theRecovery string to config.plist   ( Removes the Mac OS High Sierra recovery option ) Set Scan / Legacy checkbox to false in config.plist   ( Removes the extra Windows entries )  

      After applying the settings in Clover Configurator, save and reboot.

       Minimalist Clover boot screen. 
      Temporarily disconnect / remove your High Sierra Drive from your Hackintosh Computer. Install a 2nd drive inside the computer then install Windows on it. Reattach your High Sierra Drive. Clover will detect your Windows and High Sierra drive when you start your computer.  
      I already had Windows 10 as an EFI install on a Samsung 500GB EVO SSD on another computer. After completing my Hackintosh I then simply attached the Samsung EVO SSD into the new built Hackintosh. Upon rebooting it was detected by Clover. So I have two drives, Windows on the Samsung EVO and High Sierra on the NVMe Samsung EVO 960.
      *** There is many Nvidia Web Drivers for different builds / updates of macOS High Sierra ***
      Some times you may have to reinstall or update your Nvidia web drivers after a macOS update.
      To install the proper Nvidia Web driver ( for GTX10 Series ),  collect the following information from your macOS High Sierra installation.
      You can find this information in "About This Mac" and clicking on the System Report button. In the lefthand window, click on Software.
      macOS High Sierra Version Number macOS High Sierra Build Number
      Using this >> Nvidia Web Drivers Link. identify your build number and download WebDriver  As an example, I have build number 17C88 and I downloaded WebDriver-378. 

      Configure Nvidia Web driver in config.plist using Clover Configurator
      Mount EFI partition and drag and drop config.plist onto desktop and open with Clover Configurator. 
      Enable the following in config.plist:
           1.  System Parameters / NvidiaWeb = True ( tick )

           2.  Graphics / ig-platform-id = 0x59120003 ( Intel & Nvidia )
           3.  Graphics / Inject Intel = True ( tick )

      Save config.plist and drag and drop back into the EFI partition.
      Check Nvidia Video card is working

      Download and Install >> Cuda driver 
      Managing Nvidia Web Driver for High Sierra update's using Vulgo's Bash Script
      If you have installed an update that breaks Nvidia graphics, use the bash script to modify the Nvidia Web Driver for the new build number. 
      Download >> webdriver.sh
      Run script: 
      Configured with display cable connected to DisplayPort
      Download >> IntelGraphicsFixup ( from lvs1974 ) Copy IntelGraphicsFixup.kext to: EFI/Clover/kexts/Other Next add the iGPU DSDT patch:
      Using Clover Configurator, open config.plist Select Acpi on left hand menu. Create a new patch, click + on bottom of patches table.  Enter Comment as: change GFX0 to IGPU Enter Find *[HEX] 47465830 Enter Replace *[HEX] 49475055
      Then add:
      Select Graphics in Clover Configurator and tick inject Intel Graphics / ig-platform-id = 0x59120000 ( for Intel only and no NVIDIA )
      Download and install ( drag & drop ) in EFI / Clover / Kexts / Other folder
      AppleALC.kext ( from vit9696 ) Lilu.kext. ( from vit9696 ) CodecCommander.kext ( from RehabMan ) Edit config.plist with Clover Configurator.
      Devices / Audio Inject= 1. ( Asus Strix layout is 1, different Motherboard and audio chip ? -->supported codecs ) ResetHDA = True ( checked ) Acpi / Fixes / FixHDA = True (checked)

           4.  Look in System Report to confirm working
      Enable Nvidia HDMI Audio 
      Thanks again to MaLd0n here on InsanelyMac for explaining and patching the VoodooHDA.kext with my Nvidia graphics card device ID. 
      For Nvidia HDMI Audio, use VoodooHDA.kext, and keep AppleALC for ALCS1220A audio in kexts / other folder
      Patch VoodooHDA
      Download >>VoodooHDA.kext ( from autumnrain, slice2009, zenith432 ) Download >> DPCI Manager Right Click on VoodooHDA.kext and Show Package Contents Open Info.plist with Xcode  Finds IOKitPersonalities / VoodooHDA /  IOPCIClassMatch Change IOPCIClassMatch to IOPCIPrimaryMatch Use DPCI Manager to find  Device & Vendor ID's for your Graphics card ( example, NVIDIA GTX 1080ti the value is 0x10ef10de ) Insert the value for your NVIDIA Card Place patched VoodooHDA.kext in EFI /Clover /Kexts / Other folder
      Sound before Patch:

      Sound after Patch:


      Ports fix Is required for potential ports conflicts and bugs with sleep, restart and shutdown.
      Continuing to use the port limit patch can cause problems as it causes access outside a fixed array bounds. 
      Access outside a fixed array bound can result in other memory locations being overwritten, those other memory locations will contain data that you don't won't overwritten!. So the port limit patch is not recommended for long term use. Ports limit patch is good for macOS USB installer purpose. Ports limit patch is disabled in my POST INSTALL EFI folder.
      Below is the USB ports limit patch shown in clover configurator:

      Note, external 2x USB2 ports HS09 and HS10 are deliberately disabled to get port count below 15.
      If you have a different motherboard you can use IORegistryExplorer for port discovery and eliminate some ports to get below the 15 port limit. You can create an SSDT for port limit to use with USBInjectAll.kext. Or, If you are not keen on creating the SSDT file, then you can use "uia_exclude=" boot flag in config.plist and have USBInjectAll.kext exclude those ports.
      Rehabman has a great guide on port discovery & SSDT. >>Creating a Custom SSDT for USBInjectAll.kext
      When you know what ports you want to eliminate, then you would set custom boot flags using "uia_exclude=" in config.plist.  USBInjectAll.kext would then ignore those ports listed by "uia_exclude=" boot flag.
      Example: using "uia_exclude=" boot flag to keep USB port below 15
      If you have Asus Z370-G as per this guide then don't use custom boot flags  as it's already done with SSDT-UIAC.aml
      Disable Ports Limit Patch:

      My ABWB 802.11AC WI-FI with Bluetooth card is installed in motherboard slot: PCIE_X1_2 
      the ABWB 802.11AC WI-FI with Bluetooth card USB cable is attached on internal USB1112 header (HS12) on the motherboard.
      If you have a Wifi card with Bluetooth in a  different PCIE slot then remove SSDT-UIAC.aml from 
      EFI/CLOVER/ACPI/PATCHED and download SSDT-UIAC-ALL.dsl and change HS12 for appropriate port and save 
      SSDT-UIAC-ALL.dsl as ACPI Machine Language Binary and place file in EFI/CLOVER/ACPI/PATCHED.

      This worked for me on my first attempt, I suggest using an Apple WiFi  card for hassle free iMessages etc...
      I'm using an original >> Apple BCM943602CS WIFI+bluetooth module and adapter, this has native support in macOS High Sierra and needs no kexts / drivers. It works out of the box! 
      If you can't get a hold of this card used in this build, then try sourcing a PCIe adapter and fitting an iMac WiFi card to it.
      Purchase adapter on >> Ebay or Amazon 
      Apple iMac WiFi card, part Number >> 607-8967

      Or use a MacBook Air WiFi card & adapter, it would directly replace the Asus Wifi card and free up PCIe slots.

      Configure iMessages with the Clover Configurator
       SMBIOS / Generate New SMBIOS Profile for iMac 18,3  Check >> Serial number generated is not in use!"
           3.   System Parameters / Custom UUID ( Generate New )

           4.    Rt Variables / ROM ( Generate from SMBIOS or System )

      Windows drivers for Apple WiFi and Bluetooth devices.
      If you are dual booting with Windows and you are using an Apple WiFi / Bluetooth card like the one suggested above.
      Then chances are you won't have Windows drivers. 
      The drivers can be obtained by downloading Windows support from Bootcamp.
      Launchpad / Other ---> Bootcamp Assistant.  
      "About my Mac" will show CPU as unknown.

      Fix :
      Download >>TextWrangler ( use Text Wrangler, as other editors output code differently )
           1.    Copy and paste command into Terminal to open English.lproj directory:
      open . /System/Library/PrivateFrameworks/AppleSystemInfo.framework/Versions/A/Resources/English.lproj/
            2.   Edit AppleSystemInfo.strings using Text Wrangler.


       Edit from:
      <key>UnknownCPUKind</key> <string>Unknown</string>          Edit to:
      <key>UnknownCPUKind</key> <string>3,2 GHz Intel Core i7-8700(6-Cores)</string>
      There is now no need for ssdtPRgen.sh generated SSDT.aml for Haswell CPU and newer. 
      Power management can be configured in config.plist with Clover Configurator.
      Acpi / Generate Options / PluginType = True ( tick )
           2.  Boot / Argument / -xcmp = True ( tick )

      Test Power Management using Piker-Alpha's AppleIntelInfo.kext
      Compile source or >> download >> AppleIntelInfo.kext.zip 
      Use AppleIntelInfo.kext as per Piker-Alpha's  >> instructions
      1. Save AppleIntelInfo.kext to desktop.
      2. Using Terminal and change directory to Desktop
      cd Desktop/ 3. Enter following commands and press Enter.
      sudo chown -R root:wheel AppleIntelInfo.kext sudo chmod -R 755 AppleIntelInfo.kext sudo kextload AppleIntelInfo.kext 3. View output
      sudo cat /tmp/AppleIntelInfo.dat sudo kextunload AppleIntelInfo.kext

      Using ESP Pro or Terminal, mount EFI / ESP partition and place kexts RehabMan-FakeSMC-2017-1017 package into Clover / Kexts / Extra folder. Shutdown and restart computer. Copy and Paste HWMonitor App to Applications / Utilities.
      Download >> RehabMan-FakeSMC-2017-1017 package ( from RehabMan )

      Any  unrecognised System Memory ( Dual Channel setup etc ) can easily be set with the Clover Configurator.

      Make Backup
      1. Download and install >> Carbon Copy Cloner CCC5 
      2. Attach an external USB drive.
      3. Use Disk Utility and format external drive, create GUID partition map and APFS volume named Hackintosh.
      *Give Backup a different name from your main system drive to avoid confusion when performing a restore. So, my drive is Macintosh & backup is Hackintosh *

      4. Open Carbon Copy Cloner.
      5. Set Source as your High Sierra system drive, my drive is named Macintosh.
      6. Set Destination as your external USB drive named Hackintosh.

      7. Click Clone button.
      Restore Backup
      1. Attach macOS High Sierra Installer USB drive.
      2. Attach external USB backup drive that contains the bootable backup you made.
      3. Boot PC and press F8 and boot from external macOS High Sierra Installer USB drive.
      4. From Clover boot menu choose Boot macOS from Hackintosh.

      5. It may take a few minutes to boot High Sierra from your external USB drive.
      6. Launch Carbon Copy Cloner.
      7. Source should be external USB drive named Hackintosh.
      8. Destination should be your High Sierra installation drive. I named my drive Macintosh. 

      9. Click Clone button.
      Test Backup
      1. Follow steps 1 to 4 from Restore Backup.
      Thanks to MaLdon for taking the time to produce the DSDT for the Asus Strix Z370-G, the list of the patches can be viewed at the download link below.
      ** Only use the DSDT if you have the Asus Z370-G Strix Motherboard with BIOS update ver 0430 **
      Download DSDT here from >> MaLd0n  Place DSDT.aml inside EFI / Clover / ACPI / patched folder Open config.plist with Clover Configurator In Clover Configurator  Acpi /  Generate Options / set PluginType as False ( no check ) Reboot computer System Report before:

      System Report after:



    • By wizzord
      How is the order the different operating systems are shown in at startup decided upon ?
      Can it be changed ?
    • By gengik84
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                             http://www.hwsensors.com/releases 
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.

      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni

      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"

        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script

      Nel caso che la usb fosse ok, avrete allo stesso modo conferma dal terminale, quindi non dovrete far altro che selezionare la relativa opzione a seconda dell’installer che vorrete creare

      L'installer una volta completato è nominato "Install Mac_OS_X"

      Potete adesso passare ad installare il bootloader Clover bella vostra usb 
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra usate --> C_I_M
      Alternativa: potete usare anche lo script che ho fatto --> C_I_M.zip
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.13.... 

      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      METODO "MANUALE"....  (lascio per futura memoria)
      Copiate OS X  sulla scrivania
      Aprite ShowAllfiles per visualizzare i file nascosti. 
      Doppio click su SHOW
      Senza questa operazione non vedrete i file nascosti.

      OS X  tasto destro - Mostra contenuto pacchetto - Contenuti - Shared Support - InstallESD.dmg
      Doppio click su InstallESD.dmg
      Tasto destro del mouse sopra BaseSystem.dmg, apri.

      Tramite Utily Disco, da sinistra selezionate BaseSystem.dmg e cliccate su ripristina: 
      su Sorgente mettete "OS X BaseSystem" e su Destinazione la penna usb.
      Cliccate su Ripristina.

      Stessa procedura Fatta da EL Capitan
      Selezionate OS X Base System, poi in alto su File, modifica e poi su ripristina.
      Selezionate successivamente come destinazione USB

      Finito il processo la vostra usb sarà nominata OS X BaseSystem , per praticità rinominatela USB o comunque un nome diverso  a vostro piacimento.
      Recatevi in InstallESD.dmg” (all’ interno della app) selezionate e copiate la cartella Packages in System/Installation della USB, eliminando il collegamento esistente.
      Copiate BaseSystem.dmg e BaseSystem.chunklist, che trovate in InstallESD.dmg,  nella root  (radice)della USB. 

      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.

      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  selezionate OsxAptioFixDrv-64
                             *  :Se nel vostro sistema è presente una scheda grafica (discreta) della serie 9xx nVidia selezionate OsxAptioFix2Drv-64 al posto di  OsxAptioFixDrv-64 *
      ** OsxAptioFix2Drv :E' necessario per poter impostare CsrActiveConfig= 0x3 **
      ***OsxAptioFix3Drv oppure AptioMemory devono essere usati su hardware Skylake o successivi perché permettono alla nvram di lavorare correttamente
           (mi raccomando o uno o l'altro)
      Proseguite con l’installazione.


      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      Per installazione Legacy
      Mettete i vari Flag come da foto.

      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”

      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2

      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      *Nota: potete inserire anche il flag verbose che servirà per vedere possibili blocchi in fase di boot.
      Risulta utile quando si chiede aiuto sul forum postando la foto di tale schermata.
      Avremo la stessa funzione premendo la barra spaziatrice al boot di Clover, selezionando avvio in verbose mode.
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67

      7) Sezione System Parameters: Su inject kext mettete YES
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      L’aggiunta di  righe sopra citate comporta la totale disattivazione di questa sicurezza.
      Questo ci permette di installare, far caricare kext di terze parti e riparare permessi.
      Se volete sapere di più a riguardo vi rimetto a questo topic: http://www.insanelymac.com/forum/topic/307398-info-considerazioni-sulla-sicurezza-di-1011/
      Una volta installato e configurato il nostro osx, giusta operazione da fare sarà quella di riabilitare tale protezione.
      Impostando il valore CsrActiveConfig su 0x1 si avrà questo risultato
      Questo valore così messo, ha la stessa funzione di kext-dev-mode=1 nei precedenti osx, ma ormai obsoleto in questa versione.
      SIP parzialmente abilitata: Impostando il valore CsrActiveConfig su 0x3 si  avrà questo risultato
             Apple Internal: disabled
             Kext Signing: disabled
             Filesystem Protections: disabled
             Debugging Restrictions: enabled
             DTrace Restrictions: enabled
             NVRAM Protections: enabled
             BaseSystem Verification: enabled
      SIP parzialmente abilitata
      Apple Internal: disabled
             Kext Signing: disabled
             Filesystem Protections: disabled
             Debugging Restrictions: enabled
             DTrace Restrictions: enabled
             NVRAM Protections: enabled
             BaseSystem Verification: enabled
      SIP Disabilitata Impostando il valore CsrActiveConfig su 0x67

      Apple Internal: disabled
             Kext Signing: disabled
             Filesystem Protections: disabled
             Debugging Restrictions: disable
             DTrace Restrictions: disable
             NVRAM Protections: disable
             BaseSystem Verification: disable
      Impostando il valore CsrActiveConfig su 0x0 avremo questo risultato e SIP totalmente abilitata
      Per controllare ad installazione fatta lo stato di SIP, recarsi sul terminale e digitare questo comando: csrutil status
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Per High Sierra:
      scaricare il driver apfs.efi a fine guida,collocarlo:
      EFI/clover/Driver64UEFI se stiamo usando UEFI
      EFI/Clover/Driver64 se stiamo usando Legacy
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto-Fake+Sensors 6.26.1440.zip
    • By cvad
      Boot Disk Utility
      v2.1.2018 rev. 023b
      © cVad 2012-2018
      Latest update is always here.
      You can
      Make bootable USB Flash Disk for macOS with Latest Clover bootloader revision
      Download(with resuming) Latest! Apple Recovery HD package,
      Extract HFS-Image and Restore it with BDU.
      Automatically Check/Download the Latest Clover Rev.
      and Use existing Zip and LZMA Clover archives from Local Repository,
      Download files from User Download List
      and BDU Additional Download List,
      build FreeDos bootable drive
      with Volkov Commander.
      Feel free to click "like"

      - Make bootable USB Flash Disk for MAC OS X with Latest Clover bootloader revision fast and easy by one click! under OS Windows 7 and later.
      Not supported  WinPE and Wine. -
      Special utility from cvad & russian MAC community for new hackintosh users.


      BootDisk Utility is intended to make a external bootable USB Flash Disk by installing to it special Data set (MBR, PBR sectors and Data files) of EFI-based Clover bootloader (and may be Chameleon bootloader).
      BDU was created for new hackintosh users to simplify the installation
      of a EFI bootloader Clover to the flash drive.
      More information can be found in the appropriate forum topic:
      - Clover General discussion -
      Feel free to click "like"

    • By cvad
      Small tool to download, compile and build the latest Clover X64 package,
      possible include HFSPlus.efi, HFSPlus-64.efi.

      The script inside is editable.

      Many thanks to the comrade SunKi for help with creating the script.


      Best thanks - click "Rate File".