Is this new computer I might be getting OSx86 compatable?

Though I am not sure if it is a sempron or an athlon... So, assume it is a sempron tongue.gif

Oh, and I plan to upgrade to 512mb ram smile.gif

QUOTE
CPU: AMD Athlon™ 64 (3400+)
CPU Socket: Socket 754
Chipset: VIAR Chipset:
North bridge: VIA K8M800
- 800MHz HyperTransport interface
- Integrated UniChrome2 3D/2D graphics controller
South bridge: VIA VT8237:
- 16-bit "Ultra V-Link" host controller
- 533MB/sec. V-Link interface
Supports single channel (64-bit wide) memory interface
Two 184-pin DDR DIMM sockets
Supports up to 2GB using PC1600 (DDR200), PC2100 (DDR266), PC2700 (DDR333)
or PC3200 (DDR400) unbuffered DDR SDRAM DIMM
Memory: Supports single channel (64-bit wide) memory interface
Two 184-pin DDR DIMM sockets
Supports up to 2GB using PC1600 (DDR200), PC2100 (DDR266), PC2700 (DDR333)
or PC3200 (DDR400) unbuffered DDR SDRAM DIMM
BIOS: Award BIOS
4Mbit flash memory
Power Management: Wake-On-Events include:
- Wake-On-PS/2 Keyboard/Mouse
- Wake-On-USB Keyboard/Mouse
- Wake-On-Ring (external modem)
- Wake-On-LAN
- RTC timer to power-on the system
CPU Overheat Protection function monitors CPU temperature and fan during
system boot-up
Audio: AC97 2.2 extension compliant codec
S/PDIF-in/out compressed digital output
6-channel audio output via software
LAN: Fast ethernet LAN Phy supports 10/100Mbps
Fully compliant to IEEE 802.3 (10BASE-T) and 802.3u (100BASE-TX) standards
Graphics: Integrated UniChrome2 3D/2D graphics controller
Integrated S3 Graphics with 2D/3D acceleration
Supports 2D acceleration features
Supports 3D acceleration features
IDE: Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives
UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate up to 133MB/sec.)

Serial ATA with RAID: Supports two SATA (Serial ATA) interfaces which are
compliant with SATA 1.0 specification (1.5Gbps interface)
Supports RAID 0, RAID 1 and JBOD
IEEE 1394: VIA VT6307 PCI 1394 integrated host controller
Supports two 100/200/400 Mb/sec ports
AGP: Supports AGP 8x up to 2133MB/sec. and AGP 4x up to 1066MB/sec.
bandwidth for 3D graphics applications
Rear Panel I/O Ports: 1 mini-DIN-6 PS/2 mouse port
1 mini-DIN-6 PS/2 keyboard port
1 DB-9 serial port
1 DB-25 parallel port
1 DB-15 VGA port
4 USB 2.0/1.1 ports
1 RJ45 LAN port
1 IEEE 1394 port
3 audio jacks: line-in, line-out and mic-in
2 connectors for 4 additional external USB 2.0/1.1 ports
1 connector for 1 external IEEE 1394 port
1 connector for 1 external serial port
1 front audio connector for external line-out and mic-in jacks
1 CD-in internal audio connector
1 S/PDIF-in/out connector
1 IrDA connector
2 Serial ATA connectors
2 IDE connectors
1 floppy connector
2 ATX power supply connectors
2 fan connectors
Expansion Slots: 1 AGP slot
3 PCI slots
1 CNR slot (optional)
PCB: 4 layers, microATX form factor
24.5 cm x 23 cm (9.65 in. x 9.06 in.)


Sorry if this isnt the right place to post this, but I havnt found another forum topic that would be better to post in.