iwi 2200, nsGui not working its says "" You Can not Open Application NsGui, it may be damaged or not complete""
please help, and also guide me how to use network selector for home network with password on key index 1,cuse its automatically connects to the available free network that i can not get access to because of it has ip block

iwi3845 rel 1010

Can anyone point me in the right direction on this compile issue? define.h is failing trying to run a script, and therefore, the kext is not compiling.

I've attached the define.h debug log and the script.

scan_dev scan

iwi3945 rel 1011
iwi4965 rel 1012

nop this is wrong
i'll fix and upload a new release

done

iwi3945 rel 1013
iwi4965 rel 1014

4965 rev 1014
log 1 before i launched networkSelector
log 2 after i launched networkSelector, tried to turn the card on/off and initiate scans
I will try rebooting now if there's any problem I will post.

Here is my log, I'll be back in a few hours

scan part2
might get a kp

iwi3945 rel 1015
iwi4965 rel 1016

Doctadre,
what's wrong with your card?
you always get timeouts errors - the driver don't work with this

Im telling you, not too sure whats wrong. There are some random builds where everything works, and I get lots of activity, and then after that, its time out after timeout. I may do a reinstall to see if that helps. Im sure the chun nan kexts arent loading properly. I'll try out this build and then its on to reinstall.

post edit: crap have to redownload xcode.

iwi3945 rel 1013 -> 4 reboots, at last one I made 2 scans with networkselector

r1016 4965
1st log right after install kext
2nd after trying to initiate a scan in networkSelector and turning the card on/off
No KP yet. I will reboot and see what's happening. If there's any KP i will post.
Hope this helps

fixed tx packet code

iwi3945 rel 1017
iwi4965 rel 1018

the logs for 4965 are interesting

iwi3945 rel 1015

reboot 3-4 times, scan with netsel at 1st reboot (immediately after kext install). Then I scan at last reboot several times - scan behavior seems strange and unstable


rel 1017

scan without reboots - 1st scan with uCode errors

r1018 4965
Strangely enough this time the system did not recognise the kext immediately after install. I had to do a kextload -t to let the log going.
1. right after doing the kext load
2. after trying to initiate a scan
will reboot and see if anything's happening.
P.S. After rebooting the log seems to stop rolling. I will try to post more logs here.
P.S.2. Log 3 has the messages that kept repeating after I rebooted (the last few lines).
The networkSelector scan does not seem to make the log respond
I guess if i do another kext load it will start rolling again.

May 8 16:02:46 Forsaken kernel[0]: IOPCCard debug: en1: Discarded packet with nonexistent originating device

the driver don't tx packets
trying to fix...
this is not easy - kp expected

iwi3945 rel 1019
iwi4965 rel 1020

this is from 1017, 2 reboots, 2 scans at the 2nd reboot

This time the log starts rolling as soon as i installed the kext again
2 logs as usual.
I'mma restart now.
r1020 btw 4965

3945 rel 1019 -> single KP was before reboot after kext installation (on kextunload?), then - no KP's. Get timeouts, only 4th reboot was norm. And still have error "Discarded packet with nonexistent originating device" when scanning with netscan

same tx bug in logs...
let's try this

iwi3945 rel 1021
iwi4965 rel 1022

r1022 4965
immediate KP upon install
Reboot still KP.
What log should I post to u?
Unfortunately I don't have a good enough camera to produce a readable image of the screen when i do a -v mode >.<

3945 rel 1021 -> KP's on kext installation and on each reboot

BTW! Today and tomorrow we celebrate Victory Day, so let me congratulate you with this great holiday!

working on tx code...
please post kp so i can try to fix

iwi3945 rel 1023
iwi4965 rel 1024

R1024 4965
Cannot find a good enough camera >.< KP again. The best I could get is my iPhone and it's all blurry. Sorry I will have to hand it over to someone else.

iwi3945 rel 1023 -> only freezes (blue screen), can't get shots of KP

Sophitia - iPhone's camera is good enough, look at my shots

lol nordix, nice pics

how do you test using network selector?

code for dev_queue_xmit()
post the kp picture
you can help by trying to find out where the kp occurs

iwi3945 rel 1025
iwi4965 rel 1026

Here's my attempt. They are all the same screen (When it stopped rolling).
Must be because my laptop's screen is only 11" >.<
Hopefully it will give you a clue.
P.S. Actually they are readable. Here's rel 1024 btw i will do rel 1026 now.

REL 1023 3945

I got only KP till now and since Jalavoui asked for them,

here they are:

wait...

that kp is for 1st tx packet
fixed

iwi3945 rel 1027
iwi4965 rel 1028

r1026 4965 KP log.
P.S. Many thanks to nordix ^^

Hi Guys,
I am loading 1026 (did this in 1022,23,24) and will download 1027.
But I am getting the 'go to network preferences & press apply' in my logs, so I go to network preference pane and tell it to apply. As soon as I do, the whole computer locks up tight as a drum and just sits there. I gave it 5 minutes, never came back... Should I give it more time? I mean, all tasks stop, I had activity monitor up, and the console and they froze as well.

Network Selector now launches with my kexts loading, but I can't hit the apply w/o the computer freezing.
Suggestions?
Mark

mrprewitt what type of card do you have?
If you have 3945 then load the ones with odd rev# (1023,1025,1027 etc.)
If you have 4965 then load the ones with even rev# (1022,1024,1026 etc.)
When installing I suggest you use the kext helper as in the guide(save you lots of repair permissioins commands).
I've never encountered your problem before so I don't know but looks like you load all the drivers and test it.

I have a 3945 and I am loading each driver 1 at a time and I am using the Kextloader...
Yes, this is new.. But up until 1022, I never even had the OS recognize the ethernet 2 and give me the option of adding a 2nd ethernet.
I will go back and try the new 3945 driver that is just out....
To tell how i do it, I am using Xcode to compile each driver and I check the driver out of the SVN to make sure I am running a full complete set of software.
I nuke the old driver before compiling & installing a new one.

iwi3945 rel 1027 - no KP after kextload, several scans with network selector

I'll make 2 or 3 reboots and post here results, wait, please...

hello, here is my first log, i hope it is of some use

iwi4965 rel 1028

no KP, on restart too,my router mac address is 00-18-6E-09-E8-D8, near to the end of the log i've tried to start networkselector twice, the first time it made something (i was looking at the log with a tail command) the second time it seem it has crashed the card?

hi all, someone can post a updated networkselector or nsgui?

my kext are loaded and shows up a ethernet #2 but nsselector dont make anything...

gr8z @ all

dev_queue_xmit was disabled
enabled

iwi3945 rel 1029
iwi4965 rel 1030

another log of 1027 -> several reboots (many with timeouts), scans with netsel

Ok,
Just downloaded 1027, compiled it..
it kept saying to go to preferences and click Apply, so I did and the machine is frozen.

I am going to go get lunch and come back. If it is still frozen, I need some ideas as to why?
I am running the kaly kernel 9.2.2 on this machine.
Mark

edit - I just got back, no change. hard reboot, downloading 1030 and compiling and will try this one.

iwi3945 rel 1029 -> 3 scans, without reboots

r1030 4965
no more KP.
2 logs as usual: 1 before doing a networkSelector, 2 doing some networkSelector scan and turning the card on/off
Rebooting now as usual

local->apdev code

iwi3945 rel 1031
iwi4965 rel 1032

1029 - more info, several reboots and scans

ok,
here is the log of what happens when I boot & reboot with 1030 installed.
If I go to system preferences, it locks up.

If I use network selector to scan I get this in the log:
y 8 13:09:36 Macintosh kernel[0]: goto system preferences -> networks and press apply if you keep seeing this
May 8 13:09:36 Macintosh login[219]: USER_PROCESS: 219 ttys000
May 8 13:09:37 Macintosh kernel[0]: connect
May 8 13:09:38 Macintosh kernel[0]: check_firstup
May 8 13:09:38 Macintosh kernel[0]: goto system preferences -> networks and press apply if you keep seeing this
May 8 13:09:38 Macintosh kernel[0]: request scan!
May 8 13:09:38 Macintosh kernel[0]: ieee80211_sta_req_scan @ /Users/Mark/iwi3945/compatibility.cpp:7158
May 8 13:09:38 Macintosh kernel[0]: not ready to scan
May 8 13:09:38 Macintosh kernel[0]: en1 not running
May 8 13:09:40 Macintosh kernel[0]: check_firstup
May 8 13:09:40 Macintosh kernel[0]: goto system preferences -> networks and press apply if you keep seeing this
May 8 13:09:42 Macintosh kernel[0]: check_firstup
May 8 13:09:42 Macintosh kernel[0]: goto system preferences -> networks and press apply if you keep seeing this
May

Here is the log file...
Click to view attachment

3945 rel 1031 - > log after first kextload, scans...

Short logs, it does not roll after installing.
I did a reboot then it starts rolling again.
1 & 2 before rebooting
3 & 4 after rebooting
without and with networkScan respectively
shortly after rebooting i got a KP

ok can some on give it to me, i am tired of just getting the run around. why exactly dose the Intel 3945abg not work? what part of the apple airport system is not compatible. and what you brilliant guys are doing so that it dose work?. if you explain how and what i can do to help the process.

are you guys like re-building the apple airport driver to work with the intel card?

please explain

add pskb_expand_head()
kp expected

iwi3945 rel 1033
iwi4965 rel 1034


previous driver thread was 200 pages
if this is the thread limit maybe we can save some space by attaching logs files instead of posting

@trowa101:If you had read the website FAQs section you would've noticed. This is AFAIK:
1. There is no driver for Intel Pro Wireless cards. Apple did not write any of those to put in this system. Therefore in order to use it we have to write our own a driver.
2. jalavoui is doing a great job in tricking the OSX system into thinking that the Intel Wireless cards were Ethernet cards. So there arises one problem: the cards will require a program to control them, to scan/connect/authenticate with the networks, send and receive packets appropriately. That's the networkSelector that goes with the driver. Now we are at the testing stage to force the cards to scan/authenticate with the networks.
3. There will be no native Airport driver written for these cards, mainly because they are closed source and not well documented so it will be nearly impossible to write a new driver from 0 point. There are, however, documents on writing Ethernet driver therefore this method will be possible.
This is as far as I know. Your testing here will make the process much quicker and providing logs will be much appreciated. For more information please read the guide for testing. If you are a skilled programmer you can even join the driver developing.
r1034 4965
no KP yet
gonna reboot now

i see thank you very much. i understand what is going on now. i will try my best to help in any way possible.
good luck and i hope it works.
you shall be hearing from me soon.

iwi3945 rel 1033 -> immediate KP after install & freezes on reboots (I can't catch these KP's...)

Sorry it was my last for me. I didn't realized that it was that late already.
I will be back tomorrow. Thank you very much everyone and keep up the good work!