Full Version: Work x1950gt pro ! Dev_ID = 0x72801002 and 0x72881002 !
Pages: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32
with my x1950gt(7288) pack in post #36 there is no need to install jcools package, as I have included the atindrv
QUOTE(x86phre3x @ Aug 10 2007, 04:48 AM) 
Anybody experiencing mouse tearing after installing the kexts? Any fix?
I'm getting the same problem. And after changing my resolution to 1440x900x32 in the com.apple.Boot.plist my resolution changes to 1152x864 after reboot, any ideas?
JaS 10.4.8 Asus X1950pro Pcie not work 
(kernel crash)
(kernel crash)
hi guys, is it likely that this card will work with dual screens?
http://www.ebuyer.com/UK/product/126851
thanks
daven
http://www.ebuyer.com/UK/product/126851
thanks
daven
jas 10.4.8 sapphire x1950pro pci full working.
thanx for effort
thanx for effort
yeah.. sounds like what i was looking for!!
Only Problem.. i am quite a noob.
I am going to do a clean new install of osx tomorrow. Dont know if its going to be 10.4.8 or uphook 10.4.9.
Just bought myself a p35-DS3 board and a 6650 C2D so i have to test with version installs best.
Can anyone around here give me a step by step walkthrough for getting my x1950pro running (incl. the needed drivers?) That would be awesome!
I allready had it running with an old 6600GT AGP but since i have a more powerfull card lying around i want to use this one!
So... if anyone can help me that would be very nice. I guess many ppl could use such a guide too!
regards
MS
Only Problem.. i am quite a noob.
I am going to do a clean new install of osx tomorrow. Dont know if its going to be 10.4.8 or uphook 10.4.9.
Just bought myself a p35-DS3 board and a 6650 C2D so i have to test with version installs best.
Can anyone around here give me a step by step walkthrough for getting my x1950pro running (incl. the needed drivers?) That would be awesome!
I allready had it running with an old 6600GT AGP but since i have a more powerfull card lying around i want to use this one!
So... if anyone can help me that would be very nice. I guess many ppl could use such a guide too!
regards
MS
I am going to attempt to get my x1950pro up and running this afternoon. I sure hope it works.
QUOTE(8ender @ Aug 9 2007, 04:54 PM)
This method worked for me with no ATI Displays installed. I had a hell of a time getting anything over DVI or VGA before installing jccools driver. I think it wasn't recognizing my LCD properly.
1. Install jccools, reboot into non CI/QE mode over DVI, change resolution.
2. Overwrite all extensions with Bronya's extensions except for ATINDRV.kext, reboot.
3. It just works, even DVI!
This is with an 7280 id Ati Radeon 1950 Pro 256mb on PCI-E, running a fresh install of Tub's 4.10 Test1.
Bronya you are a star for getting this working. I've held back on running OSX on my system because of the poor video performance playing videos and such at 1680x1050. I can finally start using OSX every day.
1. Install jccools, reboot into non CI/QE mode over DVI, change resolution.
2. Overwrite all extensions with Bronya's extensions except for ATINDRV.kext, reboot.
3. It just works, even DVI!
This is with an 7280 id Ati Radeon 1950 Pro 256mb on PCI-E, running a fresh install of Tub's 4.10 Test1.
Bronya you are a star for getting this working. I've held back on running OSX on my system because of the poor video performance playing videos and such at 1680x1050. I can finally start using OSX every day.
I tried as you have made it - double display works for me through DVI, but does not work qe/ci, works only rotation!
I tried all of the driver:
1) Inside atindrv.kext 4 drivers lay - ATY_Alopias , Aty_Caretta, etc.
2) ATY_Alopias.kext is works DVI, but does not work QE/CI!
3) ATY_Caretta.kext - does not work both VGA and DVI - there is no signal!
4) ATY_Sphyrna.kext - too does not work!
5) ATY_Wormy.kext - works QE/CI and shows through VGA! Through DVI does not show, there is no signal!!!
So it is necessary to code, that worked through DVI !
Me interests that works for others through DVI.
What it " Tub's 4.10 Test1 "? Thanks!
Hi all
I try to download the initial archive from Bronya but the zip look like broken and I don't what I must change in the .kext for my X1950 Pro 7280 009a from other version :/
Please help me.
Polymere
I try to download the initial archive from Bronya but the zip look like broken and I don't what I must change in the .kext for my X1950 Pro 7280 009a from other version :/
Please help me.
Polymere
QUOTE(palote @ Aug 9 2007, 01:59 PM)
anyone with a x1950pro 512mb fully working?
Thanks in advance...
Thanks in advance...
YES IT IS!!!!!!!
THANKSSSSSSSSSSS
Here, I get a 1280x1024 display on dvi output (no GE/CI) and a "blue" screen with mouse pointer on VGA out. (Only one of eatch connected).
Have a Saphire X1950 Pro 512Mo AGP. (7280/009a)
With two monitors connected, got nothing on VGA output.
I install jccool method then apply files from Scizz.
Any idea ?
Polymere
Have a Saphire X1950 Pro 512Mo AGP. (7280/009a)
With two monitors connected, got nothing on VGA output.
I install jccool method then apply files from Scizz.
Any idea ?
Polymere
QUOTE(Scrizz @ Aug 10 2007, 09:38 PM)
so wormy would work through dvi>vga dual screens?
Nope ! One works only DVI> VGA!QUOTE(Polymere @ Aug 10 2007, 10:32 PM)
Here, I get a 1280x1024 display on dvi output (no GE/CI) and a "blue" screen with mouse pointer on VGA out. (Only one of eatch connected).Have a Saphire X1950 Pro 512Mo AGP. (7280/009a)With two monitors connected, got nothing on VGA output.I install jccool method then apply files from Scizz.Any idea ?Polymere
You should download natit.kext and atindrv.kext original ! Take here this Click to view attachment ! Work only one DVI>VGA and QE/CI !
I get ATINDRV from the Upunck 1.3 DVD 10.4.9.
Strange, after install Natit, at reboot I get trashed screen on VGA only. When I use DVI I get a message on finder that the "natit.kext" can't run correctly but I have QE/CI enabled.
I remove it and QE/CI continue to work on DVI!
The display is cloned on the 2 video output (VGA).
I notice some display "bug" under mouse pointer. Finder look like unstable when I unmout 2 volumes quicky (no gfx issue I think).
I force start on 1280x1024 and it look fine.
If there is a solution for gfx bug under mouse pointer.
Thanks for your help.
/me happy to see same result than on his iBook G4
Strange, after install Natit, at reboot I get trashed screen on VGA only. When I use DVI I get a message on finder that the "natit.kext" can't run correctly but I have QE/CI enabled.
I remove it and QE/CI continue to work on DVI!
The display is cloned on the 2 video output (VGA).
I notice some display "bug" under mouse pointer. Finder look like unstable when I unmout 2 volumes quicky (no gfx issue I think).
I force start on 1280x1024 and it look fine.
If there is a solution for gfx bug under mouse pointer.
Thanks for your help.
/me happy to see same result than on his iBook G4
For me now work 2 DVI> 2 vga! Two monitors Work! It later.
Polymere, you should edit correctly natit.kext that worked resolution through dvi! Try to do it independently.
You should register the rights for natit.kext!
Polymere, you should edit correctly natit.kext that worked resolution through dvi! Try to do it independently.
You should register the rights for natit.kext!
oh Yeah!!!
i got it running!!!! THANX A LOT!!!
Only Problem i have now is that i cant change the resolution. Its allways set to 1400x1050.
i even edited com.apple.boot and set graphic mode to 1680x1050.
but it doesnt work...
does anyone have a clue how to fix that?
i got it running!!!! THANX A LOT!!!
Only Problem i have now is that i cant change the resolution. Its allways set to 1400x1050.
i even edited com.apple.boot and set graphic mode to 1680x1050.
but it doesnt work...
does anyone have a clue how to fix that?
hey guys, when i replaced the files in the ext. folder and did the Terminal things i rebooted and got a Blue screen that changes in 3 colors blue, but nothing happens further.. i don't know what to do next :S
Got a Club3d Ati Radeon 256MB 1950 PRO on 10.4.8 Semtex kernel
Got a Club3d Ati Radeon 256MB 1950 PRO on 10.4.8 Semtex kernel
Bronya are the displays mirrored or extended display? 
i got a problem, with new drivers i get ci and qe but i cant manage res or brightness of the screen... and with jcool method i can manage it but dont have ci or qe... and with scrizz and with scrizz *zip for x1950gt 7288 i get ci but catn manage res or brightness... any idea?
QUOTE(frEEki @ Aug 11 2007, 02:46 AM)
oh Yeah!!!i got it running!!!! THANX A LOT!!!Only Problem i have now is that i cant change the resolution. Its allways set to 1400x1050.i even edited com.apple.boot and set graphic mode to 1680x1050.but it doesnt work...does anyone have a clue how to fix that?
There is a program "DisplayConfigX" which can to add resolution 1440x900 the monitor. Try search in google.com!QUOTE(MikeNL @ Aug 11 2007, 03:03 AM)
hey guys, when i replaced the files in the ext. folder and did the Terminal things i rebooted and got a Blue screen that changes in 3 colors blue, but nothing happens further.. i don't know what to do next :SGot a Club3d Ati Radeon 256MB 1950 PRO on 10.4.8 Semtex kernel
MikeNL,^kaneda, Register the rights in single user boot :kextcache -k -z /system/library/extensions
when i install the scrizz pack for x1950gt i get ci and qe but atindrv fails to load... extension isnt valid... or something...
QUOTE(Bronya @ Aug 11 2007, 04:20 AM)
MikeNL,^kaneda[/b], Register the rights in single user boot :
kextcache -k -z /system/library/extensions
kextcache -k -z /system/library/extensions
ok, i've done that, and when i get back to my 1950 istead of my 950 GMA i get the same blue screen, but with a mouse
About AGPGart.kext
Whitout agpgart on boot screen i have found first Divice ID: 0x72A0 then the right one 0x7280 DVI/CI/QE/PCI mode but poor results in xbench on CI test, OpenGL is so good(AE and Photoshop CS3 recognize my OpenGL card)...
With agpgart(v.2.2) on boot screen i have found first Divice ID: 0x7280 then the wrong one 0x72A0, AGP set to 3.0 and freeze...no way without removing agpgart.kext
What is wrong?
Can I remove that wrong ID? How?
Please help..just a little bit closer...to final working vcard!
Thanks!
Whitout agpgart on boot screen i have found first Divice ID: 0x72A0 then the right one 0x7280 DVI/CI/QE/PCI mode but poor results in xbench on CI test, OpenGL is so good(AE and Photoshop CS3 recognize my OpenGL card)...
With agpgart(v.2.2) on boot screen i have found first Divice ID: 0x7280 then the wrong one 0x72A0, AGP set to 3.0 and freeze...no way without removing agpgart.kext
What is wrong?
Can I remove that wrong ID? How?
Please help..just a little bit closer...to final working vcard!
Thanks!
can somebody help me?
i have Asus x1950 pro pcie Jas 10.4.8 i have copied 3 files from Bronya....after restart => kernel crash.
i want now update to 10.4.10 and after update install drives for GK.
you say the zip was broken? which files i need?
i want only 1280x1024 VGA and that my Gk work
i have Asus x1950 pro pcie Jas 10.4.8 i have copied 3 files from Bronya....after restart => kernel crash.
i want now update to 10.4.10 and after update install drives for GK.
you say the zip was broken? which files i need?
i want only 1280x1024 VGA and that my Gk work
Finaly It's WORKING!
AGP/DVI/CI/QE
But still poor result in Xbench QE test!
XBench Results: 29.78 (:
System Info
Xbench Version 1.3
System Version 10.4.9 (8P2137)
Physical RAM 4096 MB
Model ADP2,1
Drive Type Maxtor 6Y080P0
CPU Test 74.31
GCD Loop 130.59 6.88 Mops/sec
Floating Point Basic 76.60 1.82 Gflop/sec
vecLib FFT 47.38 1.56 Gflop/sec
Floating Point Library 83.25 14.50 Mops/sec
Thread Test 79.99
Computation 62.09 1.26 Mops/sec, 4 threads
Lock Contention 112.39 4.84 Mlocks/sec, 4 threads
Memory Test 118.01
System 113.81
Allocate 117.95 433.15 Kalloc/sec
Fill 122.19 5941.15 MB/sec
Copy 103.11 2129.77 MB/sec
Stream 122.53
Copy 110.81 2288.80 MB/sec
Scale 113.42 2343.27 MB/sec
Add 136.08 2898.70 MB/sec
Triad 134.13 2869.29 MB/sec
Quartz Graphics Test 21.40
Line 27.23 1.81 Klines/sec [50% alpha]
Rectangle 10.86 3.24 Krects/sec [50% alpha]
Circle 16.75 1.37 Kcircles/sec [50% alpha]
Bezier 65.97 1.66 Kbeziers/sec [50% alpha]
Text 33.34 2.09 Kchars/sec
OpenGL Graphics Test 70.84
Spinning Squares 70.84 89.86 frames/sec
User Interface Test 8.18
Elements 8.18 37.54 refresh/sec
Disk Test 57.18
Sequential 94.29
Uncached Write 99.70 61.22 MB/sec [4K blocks]
Uncached Write 106.22 60.10 MB/sec [256K blocks]
Uncached Read 70.88 20.74 MB/sec [4K blocks]
Uncached Read 112.73 56.66 MB/sec [256K blocks]
Random 41.03
Uncached Write 14.45 1.53 MB/sec [4K blocks]
Uncached Write 114.17 36.55 MB/sec [256K blocks]
Uncached Read 81.98 0.58 MB/sec [4K blocks]
Uncached Read 136.22 25.28 MB/sec [256K blocks]
This is what I did:
Clean instal Uphuck 10.4.9 v1.4a(no vga selected)
Install Jcool driver
Remove all Ati except atindrv.kext
Install remaining kext from Dimitrik pack
Remove kext.cache&repair permissions
Boot from Uphuck dvd again and install AGPGart.kext v2.1(cusom install)
DONE!
Still I don't understand why I have that bad results on XBench!
On my T2400 laptop with nVidia GO 7400/256 MB same Uphuck(intel) install I have much better results:
Quartz Graphics test: 123.35
OpenGL Graphics test: 117.64
Still it's an GO...Not X1950XT Pro...
What is wrong??
AGP/DVI/CI/QE
But still poor result in Xbench QE test!
CODE
XBench Results: 29.78 (:
System Info
Xbench Version 1.3
System Version 10.4.9 (8P2137)
Physical RAM 4096 MB
Model ADP2,1
Drive Type Maxtor 6Y080P0
CPU Test 74.31
GCD Loop 130.59 6.88 Mops/sec
Floating Point Basic 76.60 1.82 Gflop/sec
vecLib FFT 47.38 1.56 Gflop/sec
Floating Point Library 83.25 14.50 Mops/sec
Thread Test 79.99
Computation 62.09 1.26 Mops/sec, 4 threads
Lock Contention 112.39 4.84 Mlocks/sec, 4 threads
Memory Test 118.01
System 113.81
Allocate 117.95 433.15 Kalloc/sec
Fill 122.19 5941.15 MB/sec
Copy 103.11 2129.77 MB/sec
Stream 122.53
Copy 110.81 2288.80 MB/sec
Scale 113.42 2343.27 MB/sec
Add 136.08 2898.70 MB/sec
Triad 134.13 2869.29 MB/sec
Quartz Graphics Test 21.40
Line 27.23 1.81 Klines/sec [50% alpha]
Rectangle 10.86 3.24 Krects/sec [50% alpha]
Circle 16.75 1.37 Kcircles/sec [50% alpha]
Bezier 65.97 1.66 Kbeziers/sec [50% alpha]
Text 33.34 2.09 Kchars/sec
OpenGL Graphics Test 70.84
Spinning Squares 70.84 89.86 frames/sec
User Interface Test 8.18
Elements 8.18 37.54 refresh/sec
Disk Test 57.18
Sequential 94.29
Uncached Write 99.70 61.22 MB/sec [4K blocks]
Uncached Write 106.22 60.10 MB/sec [256K blocks]
Uncached Read 70.88 20.74 MB/sec [4K blocks]
Uncached Read 112.73 56.66 MB/sec [256K blocks]
Random 41.03
Uncached Write 14.45 1.53 MB/sec [4K blocks]
Uncached Write 114.17 36.55 MB/sec [256K blocks]
Uncached Read 81.98 0.58 MB/sec [4K blocks]
Uncached Read 136.22 25.28 MB/sec [256K blocks]
This is what I did:
Clean instal Uphuck 10.4.9 v1.4a(no vga selected)
Install Jcool driver
Remove all Ati except atindrv.kext
Install remaining kext from Dimitrik pack
Remove kext.cache&repair permissions
Boot from Uphuck dvd again and install AGPGart.kext v2.1(cusom install)
DONE!
Still I don't understand why I have that bad results on XBench!
On my T2400 laptop with nVidia GO 7400/256 MB same Uphuck(intel) install I have much better results:
Quartz Graphics test: 123.35
OpenGL Graphics test: 117.64
Still it's an GO...Not X1950XT Pro...
What is wrong??
Thank you! 
QUOTE(^kaneda @ Aug 11 2007, 09:15 AM)
when i install the scrizz pack for x1950gt i get ci and qe but atindrv fails to load... extension isnt valid... or something...
Change atindrv.kext and establish natit.kext! And repair permissions!QUOTE(MikeNL @ Aug 11 2007, 01:26 PM)
ok, i've done that, and when i get back to my 1950 istead of my 950 GMA i get the same blue screen, but with a mouse
You delete gma 950 kext !!! You try change atindrv.kext original both put natit.kext and check up! Both repair permissions! And update_prebinding -root / -force in terminal!!!QUOTE(Mafiose @ Aug 11 2007, 02:49 PM)
can somebody help me?i have Asus x1950 pro pcie Jas 10.4.8 i have copied 3 files from Bronya....after restart => kernel crash.i want now update to 10.4.10 and after update install drives for GK.you say the zip was broken? which files i need?i want only 1280x1024 VGA and that my Gk work
Update up to 10.4.10 - will be faster and will work! QUOTE(iullius @ Aug 11 2007, 03:53 PM)
Finaly It's WORKING!AGP/DVI/CI/QE But still poor result in Xbench QE test! :(Boot from Uphuck dvd again and install AGPGart.kext v2.1(cusom install)DONE!Still I don't understand why I have that bad results on XBench!On my T2400 laptop with nVidia GO 7400/256 MB same Uphuck(intel) install I have much better results:Quartz Graphics test: 123.35OpenGL Graphics test: 117.64Still it's an GO...Not X1950XT Pro...What is wrong??
What for to you AGPGart.kext??? If at you x1950 AGP you should delete AGPGart.kext and edit in folder /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Frameworks/CoreGraphics.framework/Versions/A/Resources/ file Configuration.plist, there find "IOPCIDevice" - replace on IOAGPDevice and keep, repair permissions! Also check up! But still poor result in Xbench QE test! :(Boot from Uphuck dvd again and install AGPGart.kext v2.1(cusom install)DONE!Still I don't understand why I have that bad results on XBench!On my T2400 laptop with nVidia GO 7400/256 MB same Uphuck(intel) install I have much better results:Quartz Graphics test: 123.35OpenGL Graphics test: 117.64Still it's an GO...Not X1950XT Pro...What is wrong??Click to view attachment
In general, what for you look on Xbench??? Play games and enjoy! And Xbench it can appear a mistake!
QUOTE(Bronya @ Aug 11 2007, 08:19 PM)
You delete gma 950 kext !!! You try change atindrv.kext original both put natit.kext and check up! Both repair permissions! And update_prebinding -root / -force in terminal!!!
Can you please tell me step by step?
I keep changing video card via the BIOS, so now i'm on my 950.. but when i go back to my 1950 it gives me that bluescreen with mouse which happened after i followed the instuctions in post 1
QUOTE(MikeNL @ Aug 11 2007, 11:54 PM)
Can you please tell me step by step?
I keep changing video card via the BIOS, so now i'm on my 950.. but when i go back to my 1950 it gives me that bluescreen with mouse which happened after i followed the instuctions in post 1
I keep changing video card via the BIOS, so now i'm on my 950.. but when i go back to my 1950 it gives me that bluescreen with mouse which happened after i followed the instuctions in post 1
You delete all ATI*.kext! Then take mine in 1 post the driver, and in bios disconnect gma950. You delete Integrityframebuffer.kext and check up.
but with natit i dont have control over res or brightness... only with atindrv of jcool
I have a Saphire x1950pro AGP 512mb card
I installed by taking the ATINDRV.kext from the jcool installation and placing it in the extensions folder.
Then I took the files Bronya has offered, except for ATINDRV.kext and placed them in the extensions folder.
I followed the commands to repair permissions and rebooted and my card is working.
As of right now, I have full support, although there is MAJOR mouse tearing and in system profile my card shows as PCI instead of AGP, and 256 instead of 512 mb. The system also seems jumpy and is no where as smooth as when I had my 6600GT working. It is a promising start, but there is a bit more that needs to be done to get this ready for prime time.
I have attempted to install AGPGart, which stopped QE/CI from working. I installed Natit, which caused OS X to boot to black screens. I will be attempting to get this to work pretty much all night. Any help would be greatly appreciated.
I installed by taking the ATINDRV.kext from the jcool installation and placing it in the extensions folder.
Then I took the files Bronya has offered, except for ATINDRV.kext and placed them in the extensions folder.
I followed the commands to repair permissions and rebooted and my card is working.
As of right now, I have full support, although there is MAJOR mouse tearing and in system profile my card shows as PCI instead of AGP, and 256 instead of 512 mb. The system also seems jumpy and is no where as smooth as when I had my 6600GT working. It is a promising start, but there is a bit more that needs to be done to get this ready for prime time.
I have attempted to install AGPGart, which stopped QE/CI from working. I installed Natit, which caused OS X to boot to black screens. I will be attempting to get this to work pretty much all night. Any help would be greatly appreciated.
i install the driver under 10.5 9a499,but it is not work 
here's new pack for x1950gt(7288) replaced atindrv with Bronyas new and added a gl driver
x1950gt_7288_scrz.zip
and here's natit for x1950gt(7288)
Natit x1950gt 7288
and don't forget
all thanks goes to Bronya!
x1950gt_7288_scrz.zip
and here's natit for x1950gt(7288)
Natit x1950gt 7288
and don't forget
QUOTE
sudo -s also enter the password root!
chown -R 0:0 /system/library/extensions
chmod -R 755 /system/library/extensions
rm /system/library/extensions.mkext
rm /system/library/extensions.kextcache
kextcache -k -z /system/library/extensions
chown -R 0:0 /system/library/extensions
chmod -R 755 /system/library/extensions
rm /system/library/extensions.mkext
rm /system/library/extensions.kextcache
kextcache -k -z /system/library/extensions
all thanks goes to Bronya!
Alright, tried all sorts of configurations.
The best I can get as of right now with my sapphire x1950pro 512mb AGP is one screen with QE/CI and mouse tearing. What I CANNOT get working is resolution changing, rotation, dual monitors, and I cannot get rid of the mouse tearing.
The best I can get as of right now with my sapphire x1950pro 512mb AGP is one screen with QE/CI and mouse tearing. What I CANNOT get working is resolution changing, rotation, dual monitors, and I cannot get rid of the mouse tearing.
QUOTE(8ender @ Aug 9 2007, 10:54 PM)
This method worked for me with no ATI Displays installed. I had a hell of a time getting anything over DVI or VGA before installing jccools driver. I think it wasn't recognizing my LCD properly.
1. Install jccools, reboot into non CI/QE mode over DVI, change resolution.
2. Overwrite all extensions with Bronya's extensions except for ATINDRV.kext, reboot.
3. It just works, even DVI!
This is with an 7280 id Ati Radeon 1950 Pro 256mb on PCI-E, running a fresh install of Tub's 4.10 Test1.
Bronya you are a star for getting this working. I've held back on running OSX on my system because of the poor video performance playing videos and such at 1680x1050. I can finally start using OSX every day.
1. Install jccools, reboot into non CI/QE mode over DVI, change resolution.
2. Overwrite all extensions with Bronya's extensions except for ATINDRV.kext, reboot.
3. It just works, even DVI!
This is with an 7280 id Ati Radeon 1950 Pro 256mb on PCI-E, running a fresh install of Tub's 4.10 Test1.
Bronya you are a star for getting this working. I've held back on running OSX on my system because of the poor video performance playing videos and such at 1680x1050. I can finally start using OSX every day.
Second this method, works perfect, on dual DVI, 2 screens, no tearing. Thanks very much!!
Click to view attachment
for my agp friends I have this special package:
Click to view attachment
and for my x1950gt(7288) AGP peeps:
QE/CI/OpenGL/Rotation + NO mouse tearing!
x1950gt agp
and don't forget to
TEll me how it goes
Click to view attachment
and for my x1950gt(7288) AGP peeps:
QE/CI/OpenGL/Rotation + NO mouse tearing!
x1950gt agp
and don't forget to
QUOTE
sudo -s also enter the root password!
chown -R 0:0 /system/library/extensions
chmod -R 755 /system/library/extensions
rm /system/library/extensions.mkext
rm /system/library/extensions.kextcache
kextcache -k -z /system/library/extensions
chown -R 0:0 /system/library/extensions
chmod -R 755 /system/library/extensions
rm /system/library/extensions.mkext
rm /system/library/extensions.kextcache
kextcache -k -z /system/library/extensions
TEll me how it goes
hi..
i got my 1950 pro with QE and CI enabled but when starting Adobe After Effects crashes and says that a problem occurs while invoquing OpenGL or something like that...
i can run x-bech with no problem (openGL benchs normally) but why i cant run it when opening Adobe AE???
Any ideas?
Cheers
i got my 1950 pro with QE and CI enabled but when starting Adobe After Effects crashes and says that a problem occurs while invoquing OpenGL or something like that...
i can run x-bech with no problem (openGL benchs normally) but why i cant run it when opening Adobe AE???
Any ideas?
Cheers
QUOTE(Scrizz @ Aug 12 2007, 12:14 AM)
here's new pack for x1950gt(7288) replaced atindrv with Bronyas new and added a gl driver
x1950gt_7288_scrz.zip
and here's natit for x1950gt(7288)
Natit x1950gt 7288
and don't forget
all thanks goes to Bronya!
x1950gt_7288_scrz.zip
and here's natit for x1950gt(7288)
Natit x1950gt 7288
and don't forget
all thanks goes to Bronya!
well now it works i can used EDID info from the LCD manage res and gamma... and else.. BUT the second display ( AOC 17" ) works like a mirrow from the first display and it doesnt shows up graphics/displays in system profiler... any idea of hot to use extended display??!!
QUOTE(Scrizz @ Aug 12 2007, 03:03 AM)
for my agp friends I have this special package:
Click to view attachment
and for my x1950gt(7288) AGP peeps:
QE/CI/OpenGL/Rotation + NO mouse tearing!
x1950gt agp
and don't forget to
TEll me how it goes
Click to view attachment
and for my x1950gt(7288) AGP peeps:
QE/CI/OpenGL/Rotation + NO mouse tearing!
x1950gt agp
and don't forget to
TEll me how it goes
I tried your natit package for AGP, but it didnt really do anything for me. I am running a Sapphire x1950Pro 512 mb AGP card. System Profiler showed it as still running PCI, and QE/CI were still enabled. Also, the second monitor still showed as mirrored.
I have found that disabling Beamsync and enabling quartz2d helps a lot. Also, I installed Mouse Locater which nearly got rid of all of the mouse tearing.
QUOTE(oiasdas @ Aug 12 2007, 08:09 PM)
System Profiler showed it as still running PCI
It is difficult to you to edit configuration.plist?
I went and tried that when you gave that advice to another person on here. My configuration.plist already showed IOAGPDevice. I didnt have IOPCIDevice. There was nothing for me to change, yet it still shows as PCI.
QUOTE(^kaneda @ Aug 12 2007, 07:41 PM)
well now it works i can used EDID info from the LCD manage res and gamma... and else.. BUT the second display ( AOC 17" ) works like a mirrow from the first display and it doesnt shows up graphics/displays in system profiler... any idea of hot to use extended display??!!
Try x1900natit_dual.kext from Diabolik!QUOTE(ksong @ Aug 12 2007, 06:26 AM)
i install the driver under 10.5 9a499,but it is not work
For me in leo 499 works QE/CI <-also as well as in Tiger 10.4.10!!!QUOTE(oiasdas @ Aug 12 2007, 09:48 PM)
I went and tried that when you gave that advice to another person on here. My configuration.plist already showed IOAGPDevice. I didnt have IOPCIDevice. There was nothing for me to change, yet it still shows as PCI.
You read ?http://forum.insanelymac.com/index.php?sho...8988&st=60#
That is what I see when I open it up.
x1900natit_dual.kext??? where can i download that?
QUOTE(oiasdas @ Aug 12 2007, 08:09 PM)
I tried your natit package for AGP, but it didnt really do anything for me. I am running a Sapphire x1950Pro 512 mb AGP card. System Profiler showed it as still running PCI, and QE/CI were still enabled. Also, the second monitor still showed as mirrored.I have found that disabling Beamsync and enabling quartz2d helps a lot. Also, I installed Mouse Locater which nearly got rid of all of the mouse tearing.
You Delete all ATI*.kext!!! Then establish natit.kext and original atindrv.kext from 10.4.8 or more, then establish mine atiradeonx1000.kext and atiradeonx1000ga.plugin then for you will work resolution monitor!!!QUOTE(^kaneda @ Aug 12 2007, 09:59 PM)
x1900natit_dual.kext??? where can i download that?
Any natit_dual.kext !!!QUOTE(oiasdas @ Aug 12 2007, 09:59 PM)
That is what I see when I open it up.QUOTE(Scrizz @ Aug 12 2007, 07:14 AM)
here's new pack for x1950gt(7288) replaced atindrv with Bronyas new and added a gl driverx1950gt_7288_scrz.zipand here's natit for x1950gt(7288)Natit x1950gt 7288and don't forget :Dall thanks goes to Bronya!
try this
for agp
put these in extensions folder and replace old ones
won't "show" agp, but is using agp
should give QE/CI/Rotation etc...
for agp
put these in extensions folder and replace old ones
won't "show" agp, but is using agp
should give QE/CI/Rotation etc...
i fail to get extended display, anyone could?
QUOTE(^kaneda @ Aug 12 2007, 11:33 PM)
i fail to get extended display, anyone could?
You are not able to edit ...
QUOTE(Bronya @ Aug 12 2007, 04:44 PM)
You are not able to edit ...
i edit natit with my dev id and with de secondary display id but then nothing change (it doesnt read the edid of the lcd anymore just that... ) i edit the atix1000 kext with the secondary id and then i get a kernel panic... what else i should try to edit?
ALLRIGHT!!!
NOW ITS WORKING
I finally managed to get everthing working 100%
First i installed the driver pack from jccools driver. That made my PC booting into 1680x1050 without CI/QE.
Then i installed the files from atiradeonx1950pro_dmitrik_Edited.zip.
I replaced the ATINDRV too!!!! (Leaving it from jccools made my kernel panic!)
Delete cache and fixed permissions.
TAA DAAA...
Now i have a fully supported eax1950Pro PCI-E running on my system!!
Thanx everyone for your great work and your posts on this board!!!
NOW ITS WORKING
I finally managed to get everthing working 100%
First i installed the driver pack from jccools driver. That made my PC booting into 1680x1050 without CI/QE.
Then i installed the files from atiradeonx1950pro_dmitrik_Edited.zip.
I replaced the ATINDRV too!!!! (Leaving it from jccools made my kernel panic!)
Delete cache and fixed permissions.
TAA DAAA...
Now i have a fully supported eax1950Pro PCI-E running on my system!!
Thanx everyone for your great work and your posts on this board!!!
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.