ok, so i've installed OSx86 on my Sony TR3A which is a 1 ghz centrino (intel pentium m with an intel wireless controller) the wireless won't work but the on board ethernet works natively with no problems

What about sound/graphics? What is your on board ethernet chipset?

have you tested your in-network file transfer speeds with the gigabit card?

supposedly this card can have MTU>1500

maybe 9000 or so...

with this on both ends...you might be able to get 700Mbps instead of 200Mbps... if your hard drives are fast enough...lol

ACCTON EN1207D-TX PCI Card ( with a PXE Boot-Rom Chip onboard ) - Working ( reported as a realtek model )

Have you tried the Maxxus drivers? I found that when using Vmware in bridge mnode, the network adapter in vmware would get an IP address from my DHCP but couldn't go anywhere. But it works fine in NAT mode.

WMP54GS - Wireless pci adapter with speedbooster v1.1 - Linksys

MacLover, what version of os x86 are you using (10.4.1, 10.4.3 8f1099, or 10.4.3 8f1111). Do you happen to know the chipset of your WMP54GS?

Thanks!
Mark

Anyone who posts in this thread, please post OS X version and build #, please.

I have 10.4.3 (8f1111) installed and I have onboard VIA VT6103L 10/100 Ethernet. Under the system profiler it shows up as en0 but it does not show up under system preferences. Any help would be appreciated.

Hi there. You need to install the developer tools. Go to your isntall dvd. Go to the sub dir > "XCode Tools". Excecute "XcodeTools.mpkg". Your problems will be solved!

I ran "sudo make install", I got all my bibberish. Rebooted, no luck. But I am using a Linksys LNE100TX, this is supposed to be supported. I hope I'm not doing anything wrong!

I tried the manual install also, no luck. Also tried the new version from sourceforge. Any ideas?

Intel Pro/100...works without any setup

This one is for Fuzzlet. . . .

I was kinda mad after I installed 10.4.3 on my Thinkpad A31 and the Intel 82557 wouldn't work. Not too mention the upgraded Broadcom wireless, but thats another topic . . . .So I went looking about and saw you had the same frustration. I tried a lot of things, then I went into /Library/Preferences/SystemConfiguration/preferences.plist and took a look to see what was going on. I was going to specify my IP in here cause I thought it wasn't reading what I did in System Preferences, but the IP and all was right. I checked under <key>HTTPEnable</key>
<integer>0</integer>
<key>HTTPSEnable</key>
<integer>0</integer>

and saw those zeroes and thought that was weird. Switched them to 1's and here I am the forum. Of course you should save the preferences file to the Desktop then copy to that folder to authenticate and replace the other file, I haven't rebooted but its working. . .. .. .

Ok scratch that last bit, I am an idiot at times, turns out you really want those digits to stay as '0', what does work is this:

Go into System Preferences
Go to Network
Built in Ethernet
Then Ethernet Tab
Change the Mode to Half duplex 10MBs
Click on Apply Now

Enjoy

Intel 82557 Chip on Thinkpad A31 running 10.4.3 099 build native.

I 've found a linksys LNE100TX V5.1 and download the X86 Darwin tulip driver v 1.0.0.

the tulip.kext was built in the v1.0.0 so a just had to copy it to extension forlder, change it to 755 and root:wheel and load the kext : works great in osx86 10.4.1 without problem.

had somebody tried this NIC with 10.4.3 8f1099 or 8f1111 ?

I know the lne100 or lne100tx v2 don't work, but what about v4 and v5 in 10.4.3 ?
I've seen a new tulip release v 1.2.0 but you have to compile it, has somebody
download it and compile it for 10.4.3 ?

Another problem :

I tested yesterday the nic but i will have a fast internet connection only next month,
so all seems to work as i can configure a tcp or dsl connection, ping works, the hardware
address is recognized in network prefs, the network utility shows many things, but :

what sort of tests more of a ping could i make (without any connection) in the network utility
to confirm my network card as no anomaly (because i can return it to the shop before 15 days....)

Thanks

hi there i'm new here
wanted to say that i installed osx86 native on my hdd - slave
xp on first drive

i've got a trust 108 mbps wireless pci card adapter
i installed windows vista once 3259 version and i noticed that vista reconized this card as a belkin wireless card!!!!

so i thought!!! lets give it a try and do the same within osx86
and yes it does work
you need to download these drivers and utility : STA_2500CardBus_2005_09_14 from ralink
so i can confirm this card : trust wireless turbo speedshare 108 mbps to work in osx86
with the belkin drivers.

Using the XCode tools under 10.4.3 8f1111a I was able to compile the following kext compiled from tulip 1.0.2

However, it will not load due to a failed dependency:
com.apple.iokit.IONetworkingFamily

Does anyone know how to fulfil this dependency?

Edit: Solved it myself, here is how:
http://forum.osx86project.org/index.php?sh...st=&#entry38453

I have Linksys 100tx v4 working beautifully with the Tulip driver.
You can get the kext here
http://forum.osx86project.org/index.php?showtopic=6115

A complete list of cards working under Linux with the Tulip driver is here.
http://pigtail.net/LRP/tulip.html
For OS X some may require changing info.plist in tulip.kext

Have fun!

Intel Pro/100 S Desktop Adapter from savastore.com works perfectly and as quoted.



Now need fix for dissapering ethernet config pane ???

dont working my 10.4.3

Realtek RTL8139/810x Family Fast Ethernet NIC (built into my Asus p4pex mobo)

works fine on a native install of 10.4.3 (Jas patch)

My Vitesse VSC8201 Gigabit ethernet on my Epox 9NPA Ultra is not working. This is called Nvidia Nforce Networking Controller in windows and is covered under the forcedeth driver in linux. It would be sweet if this driver were ported to darwin. Apparently there is even a Linux PPC version for it but no darwin version . I will add it to the wiki

ive got a belkin card in my desktop. dont quite know which one it is. it doesnt work, but in applications i noticed i had a belkin setup utility installed. i dont remember installing it, so im not sure where that came from. dont know if this helps you guys find a solution

10.4.3 8F1111g
IBM X40

Intel 10/100/1000 works out of the box.

IBM 10/100 ethernet server adapter works natively

Network Everywhere 10/100 NC100 v2.0 did not work

Speed Stream 10/100 SS1020 did not work but showed some sign of green light on server sometimes, who knows?

SOHOWARE 10/100 SFA110A did not work

Marvell 88E1111 GbE PHY 10/100/1000BASE-T on board DFI lanparty ut nF3 250Gb did not work

hope this helps someone

I tried to load tulip on terminal but i cant figure out how to access it, it keeps saying file not found.
i used my thumb drive to transfer it to the desktop and root file , nothing worked for me, im not familiar with terminal to get around it.

my system is using MAC OSX 10.4.3 8 f1111a JaS Patch v4.2b
3000+ amd 64, LANPARTY UT nF3 250Gb, 1 Gig DDR 400 PC3200
300 Gig 16mb cache maxtor drive, NEC DVD RW
Logitech wireless keyboard and mouse MX700
6600GT VGA leadtek

everything works fine so far except for restart hangs and on board lan did not work
floppy did not work either

Dell OptiPlex GX620 w/10.4.3 8F1111g(JaS)

Broadcom BCM5751 A1 on board does NOT work.
Intel PRO/100 S Desktop Adapter works FINE natively.

Dell Wireless WLAN 1350 Mini-PCI Card (Broadcom)

I'm Using an Encore ENL832-TX-RENT...natively, detected as Built-In Ethernet....it has the RTL-8139D Chip...ahahaha....it cost aroud 5 bucks in Chile...hehehehe...the best buy i could ever done for my OSX86

As my Via Rhine III Built-in did not work I plugged in an Intel 21143 based ethernet card (10/100mbit). It works flawlessly!

Unfortunately the Broadcom 5752 onboard doesn't work. This is the new
chipset on the new HP Workstations. But the graphics is well supported!

Onboard NVidia Networking controller didn't work, so I went to the local hardwarestore and purchased a $8 Sweex 10/100Mbit card. These all have a Realtek RTL8139 chip, so should work out of the box. And it does!

Dlink DFE-530TX+ Rev F1 doesn't work, like its brother rev C1. This is a card currently at CompUSA, but sorry.

Here is the 1.2.0 tulip kext compiled for 8f1111
http://forum.osx86project.org/index.php?sh...c=6115&hl=tulip

Marvell Yukon 88E8053 works now with 10.4.4 AppleYukon.kext located in IONetworkingFamily.kext/Contents/Plugins

humm, doing a serious dig everywhere, going to install tulip from source now.

got deadmoo's installed.

below is my NEW USB-ETHERNET dongle now.

---------------------------------------------------------------

[anshu@Fedora4 wireless]$ dmesg | grep pegasus
pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
pegasus 1-2:1.0: setup Pegasus II specific registers
pegasus 1-2:1.0: eth1, ADMtek ADM8511 "Pegasus II" USB Ethernet, 00:00:4e:11:16:c6
usbcore: registered new driver pegasus

---------------------------------------------------------------------

Any tips for me? will this work?

Help !.

Has anyone made it setting up a US Robotics Wireless PCI card ? USR5416

I tried it with the tulip drivers , well , i think i did ... i followed the steps .. but i didn't seem to succeed.
I couldn't find the device/vendor ID's

plz comment

I got my Dlink DFE-530TX+ to work under 10.4.4 by simply replacing the (Jan 3rd) version of IONetworkingFamily.kext with the one from 10.4.3 (Oct 29,2005). Otherwise it wouldn't detect it even when using Dlink's own drivers.

my wmp54g wireless pci, wit 2500, works wonderfuls wiv the new driver
gorgeous man!!
ver 10.4.3

Can you send me that IONetworkingFamily.kext (Oct 29,2005) file? I'm using 10.4.3 Jas patch but no luck for my Lan card(same as u). I dont want what is the date and version of my current kext, how can u check that?

Pls pls send me the file :X

Marvell Yukon 88E8050 works with .plist edit



http://forum.osx86project.org/index.php?showtopic=9707

wmp64g-wireless pcs
it does works well wiv the drivers for 10.4.3
but i'm not able to enter the network config menu,
it keep crashing so i can't assign a static ip to my machine....

there's a driver version for the 10.4.4 version of the same card?

I'm using a Realtek RLT8931D and it just doesn't get detected , nothing happens and
i can't connect . I'm using Mac OS X 10.4.3 8F1111 ( i think with the JaS 1111 Patch ) .
I would be really glad if someone could help me .

Thanks ,
Chaos

same here

I have a VIA Rhine III onboard, and it doesn't work. Or, well, it half-works:

1. System profiler recognises On-Board Ethernet, en0
2. Under 10.4.1, the card worked flawlessly

but Network Setup has my ethernet card there as en0, just greyed out. It's deselected, and since it's greyed out, I can't select it.

hello. this is my first post.

i installed 10.4.5 on my P4, 2,8 ghz. but now i need another ethernet-card, because my gigabit-card (onboard) doesn't work.
i have two other ethernet-cards who work there, but they are just 10/100er cards. and i want one with gigabit...

as i saw in the forum, it looks like that the card "Netgear GA311" is the one and only gigabit card that works.

but i saw too, that there are some problems with 10.4.4. how it looks like in 10.4.5?


i found this card in a online-shop (http://www.byteline.ch/index.php?cmd=show_item&target=18546). but i'm not sure, is this the right one? the product name is "Netgear PCI GA311 IS Gigabit".

it would be great if me someone can help.


thanks, wolli

i've got 3Com 905
it's not working on my 10.4.4 =(((

in the system.log i see two lines about it
"Couldn't alloc class "Apple3Com3C90x"
"Couldn't alloc class "Apple3Com3C90xB"

need help..

My board has 2 NICs built in;

Asus A8N-SLI Deluxe, Marvell 88E81001 PCI Gigabit LAN Controller (0x432011ab) (Onboard) -- Not working
Asus A8N-SLI Deluxe, NForce4 Gigabit -- Not working

I added the Marvell device/vendor ID (0x432011ab) to the AppleYukon.kext/Content/Info.plist and the NIC showed up in the list in System Preferences, and the connection lit up on the switch showing gigabit connection. However, System Preferences reports that the cable is not plugged in, while MenuMeters shows en0 as a 10mbps interface...

native install

Realtek 8139 (onboard) works fine
MiniPCI (internal card) Gigabyte GN WIAG02 - works fine

no hacks tweaks needed for any of them, toshiba A30-514 latop.

I'm running 10.4.4 build 8G1165

My onboard Davicom 9102 controller didn't work. Then I installed a Netgear FA311 and that also didn't work.

bought a wireless Netgear WG511T on ebay for $23 incl. shipping. Its a PCMCIA card, and recognized as a Airport card as long as the card is inserted when OSX is booted, if I insert the card after the boot, OSX doesn't see it.
Atheros chipset.