Get From Here

http://forum.insanelymac.com/index.php?act...st&id=13054

OK people.. see if you can figure this one out. lol

I have 3 dvd's Jas 10.4.8, Uphuck 10.4.9 1.3 rev 1.3 (4gig dvd), and a Uphuck 10.4.9 rev 1.4 (which is only a littl over 1.4 gigs)

My system is a Pentium D805 CPU, Motherboard: Intel D945GCCRL with Intel video GMA950 & LAN Intel 10/100 pro ve

I installed using the first 2 dvd's and could not get the built in network working. I tried all the above solutions and nothing. Device id for my lan is 1094 8086 by the way..

Finally out of last hope I reinstalled the system using the rev 1.4 DVD which again is about 1.4 gigs and I used a Belkin ethernet card i had lying around. It picked up a "built in" ethernet but actually the one which worked was the installed belkin pci ethernet card. I even disababled the lan in the bios and the mac os still works with the Belkin card.

I installed with only the intel 10/100 drivers selected.. nothing else. But in the end the Belkin worked.

weird uh? But its all part of the fun of experimenting with a new os i guess

One last question.. Is it normal for the OSX to install in under 12 minutes? I know theres heat and comments about the Pentium D805 being slow or outdated.. But this thing is fast.

wow caladan1810 I gotta say you're a godsend genius

I don't know how you did it but I did everything with the vendor, card id, repair permission and everything I found from the forum but I couldn't get my ethernet to work.

...But then I found your zip file and I drag everything to the folder and copy all the scripts that you have in that zip file.... And now, I'm online typing all these lines Thank you and thank you so much caladan1810.

here's my ethernet card 411:
Intel Pro /100 VE from sony laptop PCG-V505EX
Card ID is: 103D
Card Vendor ID: 8086

and Caladan1810 zip file works great for me. Thanks

Thanks Caladan1810.

It worked for me. I only added my card in the Info.plist



JAS 10.4.8
Toshiba Satellite A100/999: Intel /100 VE (card id: 1092 vendor id: 8086)

Please help me!

My instance id
PCI\VEN_8086&DEV_1064&SUBSYS_80F81043&REV_03\4&23C0B1C&0&40F0

I followed your guide to add the 0x10648086, and the Built-in Ethernet appears in the System Preferences but it is disabled. Only the Serial Port is selectable. What should I do?

Thanks cloudy!!! Lucky for me, my device ID is the same as yours. Thanks again for the help!

Thanks Brother it worked THANKS A LOT

Thanks man! you are the god for me today! After almost 2 years after this post, I still saved by you!

I tried this on my Gateway mx8734 using Leopard 10.5.1 and it didn't work.

You are a Genious. I am running 10.5.1 via Kalaway install dvd on a Gateway GT5012 and it worked perfectly. The first kext and other method did not work for me at all. This one worked perfectly fine!

Just wanted to add, it works in 10.5.2 with 915GUX. I was looking for it for months
Thanks for sharing.

There is one drawback, is does not complete work under 10.5.2 Server, you cannot start the
Server services.

Got this working on my Dell Dimension 5150C by editing the info.plist file and then running the terminal commands and repairing permissions, but after installing a couple of updates via the apple software update this seems to have stopped working. The additional text is still in the info.plist file, so i ran the terminal commands again, but to no avail.

Can anyone give me info on how to reset it to the original so i can redo everything, or give me another fix. Anyone eklse have this happen?

The Ethernet just shows up as not connected now.

TIA

Got mine working on Asus P5LP-LE with Intel82562v (Ekron) onboard NIC.

I added device ID 0x27dc8086 to <string> line below <key>IOPCIMatch</key> in Info.plist in /System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/AppleIntel8255x.kext/Contents

You will also have to move or rename AppleIntel8254XEthernet.kext in /System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/

Delete Extensions.mkext, rebuilt cache, repair permissions, reboot.

Hello

does anybody know, why my intel pro/100 VE onboard of my DELL 4600i doesnt get regonized from time to time? I have 10.5.2 running ( without QE..) and now and then it comes the line during boot up, that the content of this chip us unknown . Does someone experienced this too? I have to reboot until it gets it. Annoying...

Here is a list of device ID's + ICH that will work:
INTEL_8255X_ETHERNET_DEVICE(0x1030, 0),
INTEL_8255X_ETHERNET_DEVICE(0x1031, 3),
INTEL_8255X_ETHERNET_DEVICE(0x1032, 3),
INTEL_8255X_ETHERNET_DEVICE(0x1033, 3),
INTEL_8255X_ETHERNET_DEVICE(0x1034, 3),
INTEL_8255X_ETHERNET_DEVICE(0x1038, 3),
INTEL_8255X_ETHERNET_DEVICE(0x1039, 4),
INTEL_8255X_ETHERNET_DEVICE(0x103A, 4),
INTEL_8255X_ETHERNET_DEVICE(0x103B, 4),
INTEL_8255X_ETHERNET_DEVICE(0x103C, 4),
INTEL_8255X_ETHERNET_DEVICE(0x103D, 4),
INTEL_8255X_ETHERNET_DEVICE(0x103E, 4),
INTEL_8255X_ETHERNET_DEVICE(0x1050, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1051, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1052, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1053, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1054, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1055, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1056, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1057, 5),
INTEL_8255X_ETHERNET_DEVICE(0x1059, 0),
INTEL_8255X_ETHERNET_DEVICE(0x1064, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1065, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1066, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1067, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1068, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1069, 6),
INTEL_8255X_ETHERNET_DEVICE(0x106A, 6),
INTEL_8255X_ETHERNET_DEVICE(0x106B, 6),
INTEL_8255X_ETHERNET_DEVICE(0x1091, 7),
INTEL_8255X_ETHERNET_DEVICE(0x1092, 7),
INTEL_8255X_ETHERNET_DEVICE(0x1093, 7),
INTEL_8255X_ETHERNET_DEVICE(0x1094, 7),
INTEL_8255X_ETHERNET_DEVICE(0x1095, 7),
INTEL_8255X_ETHERNET_DEVICE(0x1209, 0),
INTEL_8255X_ETHERNET_DEVICE(0x1229, 0),
INTEL_8255X_ETHERNET_DEVICE(0x2449, 2),
INTEL_8255X_ETHERNET_DEVICE(0x2459, 2),
INTEL_8255X_ETHERNET_DEVICE(0x245D, 2),
INTEL_8255X_ETHERNET_DEVICE(0x27DC, 7),
If you have ICH8 or later controller, you're probably out of luck for this fix.
e.g.: 82566DC is supposed to have 82562v PHY, but the only controller mentioned in the architecture doc is 82577.

After you add your devID to IOPCIMatch string in 8255x Info.plist, you will have to REMOVE or RENAME AppleIntel8254XEthernet.kext to avoid using -f boot flag or other problems.

Remember permissions and cache.

Thanks for all the tutorials first of all...
I have a new issue. I got the IONetworkingFamily and AppleIntel kexts loaded. Under system preferences/network, I see ethernet listed now. My problem is that it won't pull an address. It says that the "status of your network card can not be determined.

Under system profiler, nothign shows up indicating that the card is detected.

Any ideas?

What is device ID of your NIC?

Look at System Profiler >Software >Extensions. Which networking kext's are loaded?

My device ID is 1092
The AppleIntel8255x.kext is loaded as is IONetworkingFamily. Nothing else that I can see as a networking kext.

Did you remove or rename 8254XEthernet kext?

In Sys Prefs >Network >Advanced, can you set any of the NIC properties manually?

Any errors in system.log? What about after a restart?

I did remove the 8254 kext. I can change settings to the ethernet manually, but no matter what settings I set, they always revert back to what they were before. Where is system.log located? (new to OS X)It is working now. I changed the settings from auto to manual, then back to auto. I also added the DNS server address and it worked. Not sure which corrected it, but it is good now. Thanks all.

I have a problem, here is what DPCIManager reports:



So I have added 0x10928086 to line IOPCIMatch in Info.plist in /System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/AppleIntel8255x.kext/Contents then I've moved AppleIntel8254XEthernet.kext, rebuilded Extensions's cache and repaired permissions, I've rebooted, but I can't get the LAN card working, here is what I get in system.log:

3/25/08 11:43:51 PM kernel Intel82557: Self test reports invalid ROM contents
3/25/08 11:43:51 PM kernel Intel82557: Self test reports internal register failure
3/25/08 11:43:51 PM kernel Intel82557: Self test reports serial subsystem failure
3/25/08 11:43:51 PM kernel Intel82557: Self test failed
3/25/08 11:43:51 PM kernel dsmos: Initializing...
3/25/08 11:43:51 PM kernel dsmos: Hook and decryption contexts set!
3/25/08 11:43:51 PM kernel dsmos: Starting...
3/25/08 11:43:51 PM kernel Intel82557: Self test reports invalid ROM contents
3/25/08 11:43:51 PM kernel Intel82557: Self test reports internal register failure
3/25/08 11:43:51 PM kernel Intel82557: Self test reports serial subsystem failure
3/25/08 11:43:51 PM kernel Intel82557: Self test failed
3/25/08 11:43:51 PM kernel Intel82557: Self test reports invalid ROM contents
3/25/08 11:43:51 PM kernel Intel82557: Self test reports internal register failure
3/25/08 11:43:51 PM kernel Intel82557: Self test reports serial subsystem failure
3/25/08 11:43:51 PM kernel Intel82557: Self test failed

So please, help me!

PS: Sorry for the English... I speak French.

Edit: Resolved, I've downloaded this package, installed it, deleted AppleIntel8255x.kext in /System/Library/Extensions/IONetworkingFamily.kext, deleted the Extensions.mkext, repaired permissions, rebooted, and prayed, it's finally working.
Thnak you .

That kext adds 0x27dc8086 to IOPCIMatch

No, I've added 0x10928086 to IOPCIMatch in the kext, even if, it doesn't work.

Any solution for intel 82566DC-2 Gigabit Network onboard Card.

i have the same mobo as you use in your build and installed iatkos everything works exept my lan,i tried this method but when i remove AppleIntel8254XEthernet.kext and reboot it gets stuck on the apple screen,i then have to boot in safe and put the file back in the folder,i also tried to rename it and had the same results,and suggestions?

Download this kext:
http://forum.insanelymac.com/index.php?act...st&id=23631

Do this:
1. Extract the files. Open Terminal.
2. sudo -s
3. cd /System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/
4. mv AppleIntel8254XEthernet.kext 8254X.orig
5. rm -Rv AppleIntel8255x.kext
6. cd back to extracted files
7. chown -R root:wheel AppleIntel8255x.kext
8. chmod -R 755 AppleIntel8255x.kext
9. cp -R AppleIntel8255x.kext /System/Library/Extensions/IONetworkingFamily.kext/Contents/Plugins/
10. open Network Panel in System Preferences. The NIC should be there. If not:
11. cd /System/Library/
12. rm -Rv Extensions.mkext
13. diskutil repairPermissions /
14. reboot
That should do it....NIC should be in the Network panel when the desktop returns.

tried it repeatedly and it still didnt work,i ended up putting a d-link card in and it worked,but thank you for the help

i tried everything what is write in this topic but not any success.
but i have a strange situation
after replacing the kext file i have buid in ethernet enabled but instead of my lan cand (intel pro /100 ve i have my wireless card (intel 2200 bg) witch is working fine.
anyway any help with my wire card would be appreciated.
anyway ... how can i find my device id in mac os x?
becouse i deleted windows

thanks in advance

This is instruction for everyone, witch have a problem with Intel PRO/100 VE NIC.
Installing IONetworkingFamily.kext with ID's from my ethernet card - 0x10398086 nothing changed...
but I'm seeing, when I'm on 800x600 of resolution (reboot computer) my LAN WORKING!!! But, when I'm changing my resolution to 1024x768 and reboot computer LAN DOESN'T WORKING!!! So, witch you can see, probably, there is allready one way - if you want, to LAN connection working:

-Change your resolution to 800x600 (on System preference -> Displays)
-Reboot your computer
-*when computer allready started, you will be on 800x600*
-Then you must change your resolution to 1024x768 (on System preference -> Displays)

-Now you can start working on your Hackint0sh

-When you ending working on computer, only you must to do, is turn back to 800x600 resolution (on System preference -> Displays) and Shout down your computer


Use this instruction any time, when you want to have LAN:
-Start your Leopard
-Change your resolution to 1024x768
-Have fun
-Turn back to 800x600
-Shout down.

That's all you have to do!
Yo!

hi!! im a newbie here n im stuck on fixing my LAN connection on OS 10.5.2 intel motherboard D946GZIS that has a LAN subsystem using the Intel® 82562G Platform LAN Connect (PLC) device... i tried it all but doesn't seem to work!!! Please help!!

mine Device Instance Id is PCI\VEN_8086&DEV_1092&SUBSYS_30B2103C&REV_02\4&1753FBD&0&40F0
can u plz guide me what to do with this

Hi, I am struggling a little with my network card. It says cable unplugged but about 1 in 10 times I can still use Safari to surf the net! If I boot with Knoppix CD I get the following info on the network card.

(I have cut out some of the other bits and bobs)

intel 82573l gigabit

pro / wireless 3945abg

Does anyone know how to fix this? Will the AppleIntel zip file earlier in this post work at all? This is the only think not working on my laptop (Toshiba M5) and don't want to ruin the build just for the network card which I can do without if I have to!

I understood that the network card is Intel Pro/100????? I would appreciate any help on this. I am using kalyway 10.5.2 build.

Many thanks.

Ben

I'm trying this kext out on Kalyway 10.5.2 and I've run into continuous problems. I follow the instructions to the letter and seem to hit a dead end when the system spits out:

"System extension cannot be used

The system extension /System/Library/Extensions/AppleIntel8255.kext" was intalled improperly and cannot be used. Please try reinstalling it, or contact the product's vendor for an update."

If I *dont* modify the kext, it seems to install fine, but since my hardware ID is 0x10928086 (not in the list, needs adding) nothing will turn up in the networking panel!!!

Hey man... try this sh*t ;]

This is instruction for everyone, witch have a problem with Intel PRO/100 VE NIC.
Installing IONetworkingFamily.kext with ID's from my ethernet card - 0x10398086 nothing changed...
but I'm seeing, when I'm on 800x600 of resolution (reboot computer) my LAN WORKING!!! But, when I'm changing my resolution to 1024x768 and reboot computer LAN DOESN'T WORKING!!! So, witch you can see, probably, there is allready one way - if you want, to LAN connection working:

-Change your resolution to 800x600 (on System preference -> Displays)
-Reboot your computer
-*when computer allready started, you will be on 800x600*
-Then you must change your resolution to 1024x768 (on System preference -> Displays)

-Now you can start working on your Hackint0sh

-When you ending working on computer, only you must to do, is turn back to 800x600 resolution (on System preference -> Displays) and Shout down your computer


Use this instruction any time, when you want to have LAN:
-Start your Leopard
-Change your resolution to 1024x768
-Have fun
-Turn back to 800x600
-Shout down.

That's all you have to do!
Yo!

PS: Sorry with my english...

Yeah I gave that a whirl; didn't do anything except cause it to boot back in funny colors (oddly not a low bit depth; only backgrounds and some GUI bits looked 8-bit, the rest was fine...).

Oddly, since this morning the machine has crashed a few times, rebooted oddly, magically released about 26gigs of disk space without losing any data (?) and has just rebooted now, to work perfectly, with full ethernet detection and support.

What the hell? I'd never know macs could fix themselves by crashing and not only that but wind up working even better than before!

CrArC, sounds like the system cache was finally cleared. That 26 GB must have been system cache which had your old, bad settings. On a real Mac computer it is common for the cache to get large and the machine to need a reboot every once and a while to clear out. If the Hackintosh was not clearing things correctly on reboot it may have taken the crash to get it cleared out good.

Hey guys,

my ethernet card is this guy:

intel 825xx 10/100 platform LAN connect device Rev:A00

you think these kext would work for it?
any body has a kext for this on board lan ?

I just installed Kalyway 10.5.2 on my Dell e510 and are running into a couple issues:

My network card is identified (in Windows) as:

Intel® PRO/100 VE Network Connection
\VEN_8086&DEV_27DC&SUBSYS_01Ab1028&REV_01\4&5855BE9&0&40F0

I used DPCIManager on OS X, which identifies the card as:

8086-27dc - 82801G (ICH7 Family) LAN Controller

After inserting "0x27dc8086" to the aforementioned Info.plist file, the Networking System Preferences Applet does not display a "Built-In Ethernet" tab; it only displays Firewire.

Any suggestions? I'm using the AppleIntel8255x.kext driver, and I've followed all the above instructions but to no avail. Any help at all would be appreciated.

I gave up on using the AppleIntel8255x.kext on my 10.5.2 install.

Instead, try adding the value to the AppleIntel8255x.kext under the IONetworkingFamily.kext - that seemed to work for me, once I rebooted with the -f switch.

I had added the value to Info.plist located in /System/Library/IONetworkingFamily.kext/Contents/Plugins/AppleIntel8255x.kext/Contents before posting my message... but not to the Info.plist in /System/Library/IONetworkingFamily.kext/Contents

I don't know if that makes a difference. Haven't tried booting with the -f flag; that'll be next.

Is there anything else I can do? (Thanks so far)

/System/Library/IONetworkingFamily.kext/Contents/Plugins/AppleIntel8255x.kext/Contents is the right place to put it if you're doing it that way, I assume you added the value to the list of device IDs in the plist rather than just anywhere in the plist itself. Putting it under the IONetworkingFamily.kext/Contents plist will do nothing, or brick it, I'm not sure

I also recommend trying the -f boot switch in case you're having the same problem as I am (where I have to boot with -f every time) for you though it might be enough to get it to work permanently. Also:

- remove AppleIntel8255x.kext from the /System/Library/Extensions folder if it exists
- OR add your device ID to it instead
- remove /System/Library/Extensions.mkext (kextcache)
- boot with -f to rebuild cache and reload it all

Let me know if it works, and if it does try rebooting and seeing if it STILL works

i have tried all that has been said to configure a intel pro 100 /ve
from How to forum to this and all topics...
but cant get it to work ...
method 1. used was editing info.plist with 0x27dc8086 n all cleared cache did repair but nothing seemed to happen
method 2. used was downloading the AppleIntel8255x.kext and following the instruction it ended with following error
after typing this command interminal ..
sudo kextload -v /System/Library/Extensions/AppleIntel8255x.kext
i get error saying that cant load kext missing dependecies or something alike..
my hardware is Intel 945 GNT (ICH7)

I have used Leo4all v3 to install ...

Perntium D 930
1.5GB ram 667
1.SATA HDD 80GB
2.SATA HDD 160 GB

please guide me ! if someone with similer hardware and similer version of x86osx has got it working ...

Prashant,

Are you sure that's the correct devid string? You don't seem to know your card model (Intel Ethernet 825..). That should be your first step, then find out your devid. If you're missing dependencies, find out which kexts are declared as missing and install/replace them.

DEV ID in Device manager was PCI\VEN_8086&DEV_27DC&SUBSYS_30868086&REV_01 (for my ether net controller )

I dont know any thing else than this my Ethernet controler is Intel pro 100 /ve

Step 1.I follwed steps i have attached screenshot of terminal. Snapshot 2008-05-16 03-23-34.tif


kext used was the one below.
http://forum.insanelymac.com/index.php?act...mp;id=2319(this is the link to my kext version used to perform the steps. in terminal)
AppleIntel8255x.kext (its name)

Step 2. rebooted.

Found this i mean nothing worked can somehelp me .. am i using wrong DEV ID or something. my controler is Intel pro 100 /ve DEV ID or PC ID is 0x27dc8086
ICH7 family of 27dc 8086 google it and found DEV ID 82801 G Please tell if am doing something wrong.

plus i have delete AppleIntel8254exten.kext and i am getting a lot of crash reprts my system does not boot off....

Crash reprt is . mdnsresponder: can't read hostname ..... n all

Can you copy the contents of your modified plist and paste them here?

Actually, I made a big mistake. I ended up installing some odd drivers (as a recommendation by an earlier poster) resulting in ruining my osx86 installation. I decided to start from scratch and reinstall everything, but for some reason don't have working video drivers. Why repeating the same install process yields two different results is beyond me, but I'm unable to give you a copy of the info.plist right now.

I need a bit of time to figure out why I can't see things (on a different forum of course) and I'll get the file contents to you as soon as possible. Thanks a lot for everything so far.

It's bizarre but the exact same phenomenon has happened to me across several machines - do the same the twice, get different results. Guess it keeps you on your toes

CrArC,
i have already given the link to file i replaced .. Anyway CrArC i have done it twice and got the same crash reports.. should i paste those crash reports... (those crash reports comes only if i delete that 8254 kernel extension