I have already installed iDeneb v1.3 on my laptop Toshiba Satellite L20-101:
Intel Pentium M 740 - 1733 MHz - SSE2, but no SSE3
512MB DDR2
Intel 915GM
Conexant Cx20468
Realtek RTL8139
Intel PRO/Wireless 2200BG on MiniPCI and TP-LINK TL-WN510G on PCMCIA (Atheros AR5005G)
TOSHIBA 60GB SATA
MATSHITA UJ-841S

But after installation there is "Apple" logo, and then Blue Screen. Hdd was working, so I think this is only problem with video card... I'm trying this methods:
http://forum.insanelymac.com/index.php?sho...amp;#entry42460
http://tvtool.info/go.htm?http://tvtool.in...ish/dummy_e.htm
http://forum.insanelymac.com/index.php?act...ost&id=1522
but nothing work... I'm trying to connect with VGA cable to 15" Monitor of my PC too and I don't see Blue Screen, but Black Screen and mouse coursor and that's all!
Please help me! What should I do?

Ooohh... I forgot - I used already this method - boot with -x (F8 and then -x) as well as -v -f...

Please help me, I am so close...

you might need the papperclip method

Like this:
http://gsbd41316.files.wordpress.com/2006/...3.thumbnail.jpg
?
I used already this method and paperclip 1-6 (nothing change) in VGA, and 1-6 & 2-7 & 3-8 (in this method I didn't see nothing on the monitor...).

have you try this :

http://forum.insanelymac.com/index.php?showtopic=119424

Thanks It's work, but only with -x (Safe Mode) and I can't use my WiFi, becouse I got this error "Could not get ID for kernel control. 2" (Intel 2200bg with iwidarwin drivers)

"Error: Could not get ID for kernel control. 2

This error means one of the following

* The iwi2200 driver is not installed
* The driver is installed but you have not rebooted
* The kext did not load for some reason (are you in safe mode?) "

And my sound card doesn't work too xD.

This method doesn't work for me - http://forum.insanelymac.com/index.php?showtopic=110176

But this work only with -x too (Safe Mode ;/) and this paperclip http://gsbd41316.files.wordpress.com/2006/...3.thumbnail.jpg - http://forum.insanelymac.com/index.php?sho...mp;#entry936087

Safe Mode works fine, but if I boot normally I get graphic artifacting (in all of this 3 mathods for 900GMA/915GM) so bad that the system is unusuable, can't make out anything.

Fcking Intel 915GM...

But... maybe there is some method? EFI-string? Can I generate the EFI-string for this graphic card and how I can do this?

Yea... Does it possible, to generate the EFI-string for 900GMA and whether it works??

HELP!!!

I have already "PciRoot..." from Termial:
cd ~/desktop
./gfxutil -f display
My 900GMA/915GM is PciRoot(0x0)/Pci(0x2,0x0) so what should I do now if I don't have in.plist?
Where I can get this file?

Ok, when I have get (but I don't have already) in.plist edited (past PciRoot(0x0)/Pci(0x2,0x0) and somethings else?) I should open Termial, and:
cd ~/desktop
./gfxutil -i xml -o hex ./in.plist ./out.hex

Then I have get out.hex. This file should have string, which I can past to com.apple.Boot.plist
<key>device-properties</key>
<string>*my EFI-string*</string>

Then remove kext for my 900GMA from extensions, and remove extensions.mkext.
Then reboot.

But where tha fck I can get in.plist file?