I'm glad that one of those kext works on your hack.
I'll check the mute issue on my free time. Need to meet some deadlines.


Regards.

Hi!
I can't get HDAEnabler to load. When i look in System Profile>Extensions, it's not loaded!
How can i make it load!
AppleHDA.kext doesn't load neader.

Thanks 4 any help!

I'm on iAtkos v2. 10.5.2

how do i get autosensing to work?

Try the non Toshiba kext posted on the first page... That's how I got mine working and I have a toshiba satellite a135-s4427 which has the same IAKAA motherboard as the a145-s4527...

THANK YOU BOB its working finally
you \m/ \m/

Witch kext did u use?
Can u post a link?
Thanxs, im still not runnign!!

hey, my way to get it to work was deleteting applehda, alcinject,appleazalia,hdaenabler and extensions mkexts, reboot.
after the reboot i noticed that OS somehow remember that it has drivers installed and actually in the logs i could see that it was looking for applehda.
so i deleted the extensions.mkext again. repaired permissions and rebooted again. after this i made him to "forget"(i think) about old drivers.
then i installed hda with autosensing from page 7 of this topic with hdaenabler from the first post using kexthelper. repaired permissions just to be sure, deleted manually(i didn't trust kexthelper saying that he did it already) extensions.mkext. at this point i got sound even before restart. i just waited about one minute. the OS loaded the applehda and hdaenabler and sound was working. now i have sound with autosensing. the headphone ports aren't listed till i connect the mini-jack. after pluggin in, sound device changes from internal speakers to headphones. if i unplug them, it changes back to internal speakers
hope this helps



these are the kext. the first one is applehda with autosensing and the second one is without external headphones. the hdaenabler is in the post #1

i used the alc861vd.mpkg.zip by eddie94 in post number 109
i removed azalia from extensions folder
ran the package and installed the toshiba option
then i repaired permisions

after i did the above steps it didnt work autosensing was not working so bob2600 told me to try the other option which was not for toshiba in the alc861vd.mpkg.zip then i ran the installer again this time i checked the other option not meant for toshiba
repaired permissions

and got my headphone jack working!!!

hope it helps you too

@BRAVESKUNK
THANK YOU

i could not get them to load on 10.5, but i had to update to 10.5.5, same might apply to you.

try loading them manually

go to terminal and type these commands:

sudo -s (it will ask for your password, type it but you wont see it this is normal though press enter)

cd /System/Library/Extensions/ (note casing here)

kextload -t HDAEnabler.kext (it will try and load, if it can it will, if it cant load it will tell you why)

kextload -t AppleHDA.kext (as above)

post here the results of the two kext loads

Thanxs a lot for ur data!
The Kexts loads now, but i don't get hardware detection on my Audio>Pref. pannel.

ffffffffffffffffffff

Any ideas?

THanxs again!!!

Do u think i had to update to 10.5.5
I'm on a Dell Vostro 1710, Osx86 iAtkos v2 10.5.2

Has anyone figured out the quality issue with the internal speakers in the kext yet?

kextload didnt give any errors? wht exactly did it say?

any messages in system.log/console.log during booting up?

Thanxs a lot to all u friends!!!
I have Audio, since i reinstall the kexts files and clean the cahces. I touch de startup config on my dell, and voila.
Now i'm trying to get mic into work!!!

Thanx again, and if someone has any idea on the mic, glad to hear!!!

Leo

I tried it... Now I have IntSpeaker, HeadPhones, Mic and Volume control with balance but no mute on my ASUS X51L notebook (Retail Leopard 10.5.4 + Chameleon HD). It showes devices in System Profiler.

Realtek ALC660 @ Intel 82801HBM ICH8M - High Definition Audio Controller PCI

Thank You very much! Sorry for my English...

MadTux, in windows the volume is mooooore hig then os x, in windows externals Speaker are a hig volume, but in os x the volume IS SO LOW, can you fix this?
thanks!

MadTux where are you ?

Hi all

I ve Asus F5SL with Alc 660(Audio)

Intel High Definition Audio:

(Device ID: 0x10431783)
(Audio ID: 12)
(Available Devices: ) -> in sytem profiler

After try more and more tip and tricks i found this thread

I Remove AppleAzaliaAudio.kext (in System/Library/Extensions)
I Install HDAEneabler from Kabyl and the ALC (ALC660/660VD) kext

I Repair permissions and kextcache and reboot...

After Reboot it Works (i am happy) i ve sounds but only internal output works
not internal micro if anyone know how i do tell me
in preference i see my card but fader volume doesn't modify the threshold of volume not works for me...

Could anybody help me, please.

I installed Kalyway 10.5.2 in my Toshiba A100-796.
The problem i have is sound card, i have ALC681 according to the offical website of Toshiba.
but i found DEV:0862 and VEN:10ec from windows vista.

So i installed ALC681VD, for Leo and Toshiba version. both of them is working except my external sound input.
Any body knows how to solve the problem?

My controll ID is 0x27D88086, and sub 0x1179ff10.

Thank you

Acer Extensa 4620Z with Intel HDA Audio, Realtek ALC268 Success! The files linked in this post are the answer!

How I Installed
Download MadTux_collit99_ALC268_B.zip from ALC268 Tiger/Leo section
Download HDAEnabler.kext.zip from HDAEneabler from Kabyl section
Unzip files
From the command line:
sudo rm -rf /System/Library/Extensions/AppleAzaliaAudio.kext
Using Kext Helper b7 Install HDAEnabler.kext when it says restart click cancel
Using Kext Helber b7 Install ApppleHDA.kext from the MadTux folder when it says restart click cancel
Open OSx86Tools and run all the systems maintenance scripts
reboot and if you're lucky...

Built in mic works. Built in speakers work. When I plug into the headphone jack sound is routed to the headphone jack. I have not tested either input ports, but so far it works PERFECTLY!

Thanks!

MadTux,UP!!!

Well, after couple weeks now I can say that this new ALC 660-VD driver really works better and I have no longer had problems with shuting down (in the begining I thought it works in about 50% cases).

But my audio output in my laptop is silent and with other drivers I was able to connect external speakers. Can you guys fix it?

Plzzzzz any Drive For ALC861 Not ALC861VD
it's come with Toshiba a 100 ALC861 10.5.4 The mic it's not working anything els it's work Fine .
any help plzzz

Is madtux still alive?

Has anybody got mic working?, I have ALC861-VD or 862 on a MSI mother board, no laptop.
I get loud noise from external mic, and it only gets really loud sounds, that end up sounding distorted.
Anyone with this same issue?
Anyone knows if it should work?

on Laptop ASUS F5SL, details are here,
following package was installed, crashed after reboot with following error message:

Nov 30 12:46:31 localhost kernel[0]: HDAEnabler: Copyright © 2008 by Kabyl
Nov 30 12:46:31 localhost kernel[0]: HDAEnabler: 05/05/2008 Added SPAudio support:Taruga
Nov 30 12:46:31 localhost kernel[0]: Sound assertion "0 == fInterruptSource" failed in "/SourceCache/AppleHDA/AppleHDA-157.1.24/AppleHDAController/AppleHDAController.cpp" at line 215 goto Exit1

the only working solution found so far is installing following MadTux AppleHDA from Wiwi post here

hi,

i have installed the driver acl268 and the sound workes perfect!
only the mute doenst work... does anyone have a solution for the mute??

i've got a HP Pavilion dv9790ed

Not working on Packard Bell BG46. LSPCI gives 82801H HD Audio controller Rev04 on 8086:284b. I've tried ALC268/660/861 and even Azalia, nothing works. The only thing that has changed, was Audio properties in System Profiler - displaying device ID 0x163C10A and Audio ID 12. Guess AppleHDA needs patching for this chip... Cheers to everybody!

Excellent work ! Thanks everybody who participated in this.
On Laptop Acer Extensa 5620,alc268, says :

Intel High Definition Audio:

Device ID: 0x1025011F
Audio ID: 12
Available Devices:


But auto-detecting headphones work ! No idea about mic, can`t test right now. Thanks again !

I have a Toshiba M105-S3004 Laptop and I tried the ALC861 kext. It didn't work ... Is there anything else I can try? Or another sound card that I can purchase that will work with my Windows/Mac OS X dual boot?

Hello All,

I've been trying different ways to install this kext for my audio. I have the ALC268 hardware. So far, the most success I had was using Taruga's method. Unfortunately with this method, it doesn't do auto-switching when I plug in a headset. The mic doesn't work or isn't recognized and when the computer wakes up from sleep I don't have audio anymore. I can still work the volume up & down but there is no audio coming out of the speakers nor the headset (if I switch it manually). Can somebody help me? I'll be attaching the codec dump. I really need your help.


Codec: Realtek ALC268
Address: 0
Vendor Id: 0x10ec0268
Subsystem Id: 0x152d0776
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=4, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0
IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0
Node 0x02 [Audio Output] wcaps 0x1d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x28 0x28]
Converter: stream=0, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x03 [Audio Output] wcaps 0x1d: Stereo Amp-Out
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x21 0x21]
Converter: stream=0, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:
rates [0x5e0]: 44100 48000 88200 96000 192000
bits [0x1e]: 16 20 24 32
formats [0x1]: PCM
Node 0x07 [Audio Input] wcaps 0x100111: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x160]: 44100 48000 96000
bits [0x6]: 16 20
formats [0x1]: PCM
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x100111: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x160]: 44100 48000 96000
bits [0x6]: 16 20
formats [0x1]: PCM
Connection: 1
0x23
Node 0x09 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0d [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0e [Audio Mixer] wcaps 0x20010a: Mono Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00]
Connection: 1
0x02
Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Connection: 2
0x02 0x1d
Node 0x10 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x80 0x80]
Connection: 3
0x03 0x1d 0x02
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x99a30920: [Fixed] Mic at Int ATAPI
Conn = ATAPI, Color = Unknown
DefAssociation = 0x2, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Node 0x13 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Node 0x14 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x081003c: IN OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
Conn = ATAPI, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x0f
Node 0x15 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x081003c: IN OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x0221401f: [Jack] HP Out at Ext Front
Conn = 1/8, Color = Green
DefAssociation = 0x1, Sequence = 0xf
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=04, enabled=1
Connection: 1
0x10
Node 0x16 [Pin Complex] wcaps 0x40010c: Mono Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80]
Pincap 0x0810: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Connection: 1
0x0e
Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x083734: IN OUT Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x02a19830: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
DefAssociation = 0x3, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=00, enabled=0
Connection: 1
0x02
Node 0x19 [Pin Complex] wcaps 0x40008b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0
Amp-In vals:
Pincap 0x083724: IN Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=00, enabled=0
Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x083734: IN OUT Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x02
Node 0x1b [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1c [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Node 0x1d [Pin Complex] wcaps 0x400000: Mono
Pincap 0x0820: IN
Pin Default 0x4015822d: [N/A] Speaker at Ext N/A
Conn = Optical, Color = Purple
DefAssociation = 0x2, Sequence = 0xd
Pin-ctls: 0x20: IN
Node 0x1e [Pin Complex] wcaps 0x400380: Mono Digital
Pincap 0x0810: OUT
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=10
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x23 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1
Amp-Out vals: [0x01 0x01]
Connection: 7
0x18 0x19 0x1a 0x1c 0x14 0x15* 0x12
Node 0x24 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1
Amp-Out vals: [0x01 0x01]
Connection: 7
0x18 0x19 0x1a 0x1c 0x14* 0x15 0x13

I tried to unload AppleHDA and HDAEnabler kexts before sleep, but it's crashed.

TAHT WORKS WITH MY LENOVO 3000 c200!!!

Thanks MadTux!

I installed MadTux_collit99_ALC268_B.zip. seems working well.

but,
system profiler say:
Intel High Definition Audio:

Device ID: 0x17AA4010
Audio ID: 12
Available Devices:

and no sound after wakeup from sleep..

Good to see I'm not the only one who can't get it working after sleep.

Madtux I did this and it killed my whole OSX install. I had to go into safemode and delete the appleHDA kext and then reboot and finally it worked. I'll keep working on this. I also had the applehda.taruge to and maybe thats why i was having the trouble.

Any insight you can offer would be great. I looks like development on this driver has stopped again. I hope I can get it to work with its current release.

Thank you man.

hi madtux
ive got a lenovo 3000 c200 with alc861VD (alc862) and i tested ur kexts. They work great with volume control except mute as u said.
the problem is with micro. it doesnt work internal nor external

the problem is with micro. it doesnt work internal nor external
I also have the problem! Does somebody can fix it?Click to view attachmentThis kext can have sound and mic, but the sound can"t control! Sorry for my poor english.

I have 10.5.5, if I had those kexts I get no sound at all. With the XxX original I get sound but not mic except that white noice.

I have the AAO 110 btw.

Ideas?

Also have the issue with sleep on my Dell Mini. Any help would be appreciated!

i followed your instructions and sound in my laptop didn't work, i did try with alc268_a and alc268_b, if i go into (system preferences/sound) there is no (output devices found)

if i reboot in verbose mode i see this (applehda.kext failed to load: unable to locate "layout-id" property.)


the installation i use was ipc 10.5.6, i only selected, voodoo kernel, mcp67 chipset driver, and ps/2 for the keyboard, nothing more


my laptop is-

acer aspire 4520

athlon 64 x2, processor

nforce 610, chipset

alc268, sound card

geforce 7000m graphics



thanks

So, no sound after sleep here... I'm using EHCISleepEnabler.kext to get sleep to work.

I have Lapptop Toshiba A200-1CR with ALC862 (checked under Windows in drivers details).
I've tried to install KEXT from first page on Leo 10.5.5 but I don't have sound at all.

As it is described on 1st page I copied HDAEnabler from Kabyl and ALC KEXT and used OSx86 tools to fix permissions and clear extension cache. After reboot I don't have sound at all (I have never had). I have tried with all KEXT (861, 862, 268).
Maybe it is worth to mention that I hadn't Azilla file on my disk so I didn't remove it.

What I did wrong - any ideas ?