Jump to content

camzgon

camzgon

Member Since 23 Jun 2010
Offline Last Active Jun 12 2016 06:27 PM
-----

Topics I've Started

Realtek ALC268 @ Intel 82801IB ICH9 kext required

27 June 2010 - 07:36 PM

Anyone have a working, or even partially working kext for this? I've tried a few but none of them work

Acer Aspire 5735z Install Iatkos s3 v2 Help

23 June 2010 - 09:21 PM

Hi guys, I've been at this for about 2 days. I tried using the retail edition of snow leopard, then I moved onto iatkos. Anyway,

Install process was a hit and miss, sometimes it would load (take 5 minutes) if I used the above options, sometimes install wouldn't load at all (even if I used those options or nothing at all), If I used no options, it would stay on the grey screen with no animations. If I did the options it would take a while before going to the install screen. And even then, sometimes the touchpad would be unresponsive.

I left the kernel on default, installed the drivers for the ethernet, wireless and left the VGA unchecked. AFter installation finished and rebooted, I first tried booting with any options, it wouldn't boot. I then tried it with the above flags that I used when trying to get the installer to run, it would take about 5 minutes and give the following kernel panic error
Posted ImagePosted Image
Posted Image

I would like to start again, maybe get install to run smoothly and choose the correct settings. I have an acer 5735z, here are the specs taken from everest ultimate edition

CPU Type Mobile DualCore Intel Pentium T4200, 2000 MHz (10 x 200)
Instruction Set x86, x86-64, MMX, SSE, SSE2, SSE3, SSSE3
Min / Max CPU Multiplier 6x / 10x

Front Side Bus Properties
Bus Type Intel AGTL+
Bus Width 64-bit
Real Clock 200 MHz (QDR)
Effective Clock 800 MHz

Mobile Intel® GMA 4500MHD
Video Adapter Intel GL40/GM45/GM47/GS45 Chipset - Graphics Controller 0 [B-3]

Wireless: Atheros AR5009 802.11a/g/n Wireless Network Adapter
Ethernet: Marvell Yukon 88E8071 PCI-E Gigabit Ethernet Controller
Audio: Realtek ALC268 @ Intel 82801IB ICH9

Any help would be appreciated. Oh and I'm installing on an External IDE hard drive.

PS:
When it doesn't load the installation disk, I get the following error

USBF: 0.455 AppleUSBEHCI[0x600a800]: unable to get filterInterruptedEventSource
USBF: 0.456 AppleUSBEHCI[0x600a800]: UIMInitialize - Error Occurred (0x******) (can't make the rest of the code out from photo)
USBF: 0.460 AppleUSBEHCI[0x600a800]: start unable to initialize UIN
mblnlt: done (64 MB memory set for mbuf pool)

Then the disk stops reading.

I just tried to boot the setup again, but just using -v -f cpus=2, I left out the bus ratio.

It got stuck on
Bug: launchctl.c:2325 (23930):39: (dbfd = open(g_job_overrides_db_path, 0_RDONLY | 0_EXLOCK | 0_CREAT, S_IRUSR | S_IWUSR)) != -1

2 minutes later it shows under it
systemShutdown false

This stays for a good 5-6 minutes while the CD is buzzing away, like the laptop is trying to find something. Afterwards, it loaded, but the touchpad wasn't moving. Brilliant.

Eitherway, if installation loads, and the touchpad works, the above bug and systemshutdown messages are shown regardless.
© 2017 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy