Jump to content

MaLd0n

MaLd0n

Member Since 14 Jan 2010
Offline Last Active Private
*****

Posts I've Made

In Topic: [Guide] Sierra/High Sierra on mobos Serie 200 / KabyLake / DSDT

Yesterday, 01:46 PM

Hey MaLd0n,

 

your support is amazing! So here is my Setup:

 

i7 7700k

Asus ROG Strix z270i

32 Gb RAM

GTX 1060 3GB

Samsung 960 pro 512GB

macOS 10.13

 

So far my System is running quit good, im having Geforce web driver installed and working. The Setup even sleeps properly and front Panel USB's are working. Im having trouble getting full USB 3.0 speed, there are Sound devices detected but no sound coming form them, also HDMI Sound would be nice. I hope you can help me out with your DSDT's.

 

thx a lot!

Attached File  CLOVER.zip   2.36MB   7 downloads


Thanks MaLd0n. I appreciate what you are doing for everyone. 

 

The DSDT and/or clover you provided me doesn't seem to work. I get panics (and a weird Don't steal macOS). I've went back to mine for the time being. Thanks!

use fresh install and follow first post

In Topic: [Guide] Sierra/High Sierra on mobos Serie 200 / KabyLake / DSDT

16 October 2017 - 04:54 PM

Thank you sir! I will try this when I get to home to my Hackintosh. Should I start over from scratch and install Sierra/High Sierra, then replace with your Clover to get USB 3 working? 

ye

kabylake need 10.12.6 or HS for native support


Works perfectly ! Thank you very much MaLd0n. ( GA-z270 Gaming k3 bios F8 + 7700k + Nvidia gtx 1070 + ssd 960 samsung evo 500 Gb. )

welcome

enjoy

In Topic: [Guide] Sierra/High Sierra on mobos Serie 200 / KabyLake / DSDT

16 October 2017 - 02:00 PM

Hello MaLd0n!

 

I finally got all of my files together and I need your help editing my DSDT. My objective is to enable USB 3.0 and to run full speed on my motherboard. Here is the link to my files due to attachment limitations:

 

https://www.dropbox.... files.zip?dl=0

 

Note: I did not replace my clover folder with yours as instructed. (I am running El Capitan 10.11.4) 

 

My hardware configuration:

 

CPU: Intel i7 7700

MB: Asus Z270G with Wifi/BT

Graphics: GTX 980

Case: Phanteks Evolv ATX

Storage: 256 GB SATA SSD

use Sierra 10.12.6 or High Sierra for native support

Attached File  CLOVER.zip   2.31MB   8 downloads


Damn you went to work! Ironically, I got the install to work using Pike's patches on 10.12.6 like before, but making another (3rd) boot stick with Unibeast instead of createinstallmedia worked. I just switched out the plist and drivers to be custom for the board. I bet it was just a corrupted installer. I appreciate the help! Your EFI here matches the one I made, so I'm guessing that two people with the same result should be a good idea?

;)

In Topic: [Guide] Sierra/High Sierra on mobos Serie 200 / KabyLake / DSDT

14 October 2017 - 04:05 PM

Guys, if need edited DSDT, post files, check first post

Welcome!

In Topic: [Guide] Sierra/High Sierra on mobos Serie 200 / KabyLake / DSDT

13 October 2017 - 06:45 PM

what id u use in clover, in dsdt i inject 1, if work in clover, just use correct id for ur codec

© 2017 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy