toanbk

TheRacerMaster, on 11 May 2013 - 03:50 PM, said:

Hi, I fixed your DSDT errors, warning, and add ; DTGP method, hack RTC, HPET, SMBUS. Try it, good luck

anyone can help me ?

I followed this tut, my brightness bar is appear but it not effect. I upload DSDT, please review DSDT for me, thanks

Thanks you, here is my dump code :

pcilib: 0000:00:02.0 64-bit device address ignored.
00:02.0 VGA compatible controller: Intel Corporation Arrandale Integrated Graphics Controller (rev 12) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Unknown device 14c2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d3400000 (64-bit, non-prefetchable)
Region 2: Memory at <ignored> (64-bit, prefetchable)
Region 4: I/O ports at e080
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4090
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCIe advanced features <?>
00: 86 80 46 00 07 04 90 00 12 00 00 03 00 00 00 00
10: 04 00 40 d3 00 00 00 00 0c 00 00 a0 0f 00 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 43 10 c2 14
30: 00 00 00 00 90 00 00 00 00 00 00 00 10 01 00 00
40: 09 00 0c 01 26 61 b1 00 88 00 c0 00 0f 17 17 17
50: 00 00 50 03 0b 00 00 00 00 00 00 00 00 00 00 ae
60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 05 d0 01 00 00 00 e0 fe 90 40 00 00 00 00 00 00
a0: 11 11 11 00 13 00 06 03 00 00 14 60 25 04 3a 30
b0: 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 a4 22 00 00 00 00 00 00 00 00 00 00 01 02 00
e0: 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 ab 0f 14 00 18 a0 d9 aa

and my BAR1 address is D3400004 ?

Quote

I don't know how to modifile, please help me

I tried:
step 1: remove Nati.kext
step 2: + add hack code to the last DSM method => NOT WORK
            + Remove all code in DSM method, then add only hack code to DSM method => NOT WORK