Jump to content

3 issues ive had on my clover 4790k for a year with no solution


pianoguy
 Share

14 posts in this topic

Recommended Posts

Hello, these are 3 issues ive had on my 4790k clover build, since day one, and through many OSs, and I have never found a solution to any of them. Here are the issues:

 

1) My Ram has always shown as under-clocked. I have 1866 speed Ram, but it has ALWAYS shown as 1777 speed in the Mac install (ive been through yosemite, cap, and now sierra, have updated clover every now and then etc, same issue). The bios and the windows install both see correct speed.

 

2) Bios sees the Mac install as several duplicated devices (ie, if I go to bios to choose boot device, or i press f8 on boot for boot menu, it shows "mac os 256gb ssd etc" like 10 times in the list. Eventually, the list grows to a point where it will no longer boot until I clear CMOS and get it back down to being listed once, about every other month.

 

3) Shutdown speed has always been extremely slow. I have an SSD, and even when the install is clean and new, this issue exists. It takes about 45 seconds or more to shutdown (bootup is still fast, about 10 seconds). This is very annoying, it should take about 3 seconds to shutdown.

 

Please help me with these, guys. Thanks

 

My hardware is:

4790k CPU, Asus z97 Pro Wifi AC mobo, 16gb of 1866 ram, samsung SSD, 980ti, using clover on uefi

Link to comment
Share on other sites

thanks for the replies. I enabled trimforce a while back (dont know if I have to re-enable on each OS update?) ill check status and re-enable. I dont think its that because as I said, the slow shutdown has ALWAYS been an issue, even when it was a new install with trimforce enabled, and no apps open. I dont have a dsdt (I was told a z97 4790k doesnt need one) unless you mean one of the ones generated by clover in the efi folders. 

 

Here are my kextstat and ioreg https://www.dropbox.com/s/72hjbzr262x8sgm/ioregKS.zip?dl=0

Link to comment
Share on other sites

the complete ioreg is ioreg -fl

 

pianoguy

 

if u have asmedia usb in ur mobo, i think the problem is there

 

what is LogJoystick? Cycling74.driver.Soundflower? p.co.kuwatec.driver.kuwatecAudioLoopback?

 

is a usb devices?

 

if yes, unplugged and test

 

post ur dsdt here, bro. ill check

Link to comment
Share on other sites

Put your config.plist here too.

And extract your IOReg like this: http://www.rampagedev.com/?page_id=77

 

 

the complete ioreg is ioreg -fl

 

pianoguy

 

if u have asmedia usb in ur mobo, i think the problem is there

 

what is LogJoystick? Cycling74.driver.Soundflower? p.co.kuwatec.driver.kuwatecAudioLoopback?

 

is a usb devices?

 

if yes, unplugged and test

 

post ur dsdt here, bro. ill check

 

here are my iroeg (using app) and config file. I dont have a dsdt (I was told I wouldnt need one with this configuration) https://www.dropbox.com/s/l2mew05exnvrmlh/slowshutdown.zip?dl=0

 

Logjoystick is probably a driver for using a game controller as a mouse. The other 2 drivers mentioned are virtual audio cable drivers (to route audio inside computer from one app to another)

Link to comment
Share on other sites

Try this: attachicon.gifconfig.plist.zip

 

And it would be good if you use an SSDT modified. Look in Piker's site, and generate one.

I do have an ssdt in the "patched" folder that was made with the pike script plus the 6300 tag. Is clover set to not use it this entire time?

here is my dsdt (i clicked save as). https://www.dropbox.com/s/ny62mhfk86vok85/System%20DSDT.zip?dl=0

  • Like 1
Link to comment
Share on other sites

 Share

×
×
  • Create New...