Jump to content

FakeCPUID, XCPM and generating ssdt.aml


ekwipt
 Share

20 posts in this topic

Recommended Posts

So i am having some problems with my install Sierra PB7, I've managed to get the xcpm patches working (Credit © pikeralpha © okrasit) only by using fakeCPUID 0x040674, I've read a lot of people being able to get the patches working without having a fakeCPUID, so i'm at a bit of a loss here. I'm also not having to use the kexts:

NullCPUPowerManagement.kext
VoodooTSCSync.kext

Running the following patches in clover:

xcpm_bootstrap Sierra © Pike R. Alpha
Find      83C3C483FB22
Replace 83C3C183FB22

xcpm_core_scope_msrs  © Pike R. Alpha
Find      BE0200000031D2E86CFCFFFF
Replace BE0200000031D29090909090

xcpm_pkg_scope_msr  © Pike R. Alpha
find      BE0700000031D2E894FCFFFF
replace BE0700000031D29090909090

I've generated a ssdt.aml and placed in ACPI/patched folder using ssdtPRGen.sh
Also ran freqVectorsEdit.sh
Then ran AppleIntelInfo and get the following output:

AppleIntelInfo.kext v1.6 Copyright © 2012-2016 Pike R. Alpha. All rights reserved

Settings:
------------------------------------
logMSRs............................: 1
logIGPU............................: 0
logCStates.........................: 1
logIPGStyle........................: 1
InitialTSC.........................: 0x7f18d438849 (256 MHz)
MWAIT C-States.....................: 8480

Model Specific Registers (MSRs)
---------------------------------------

MSR_CORE_THREAD_COUNT..........(0x35)  : 0x6000C
----------------------------------------
- Core Count......................... : 6
- Thread Count....................... : 12

MSR_PLATFORM_INFO..............(0xCE)  : 0x20080C3BF3812200
----------------------------------------
- Maximum Non-Turbo Ratio............ : 34
- Ratio Limit for Turbo Mode......... : 1 (programmable)
- TDP Limit for Turbo Mode........... : 1 (programmable)
- Low Power Mode Support............. : 1 (LPM supported)
- Number of ConfigTDP Levels......... : 1 (additional TDP level(s) available)
- Maximum Efficiency Ratio........... : 12
- Minimum Operating Ratio............ : 8

MSR_PMG_CST_CONFIG_CONTROL.....(0xE2)  : 0x3
----------------------------------------
- I/O MWAIT Redirection Enable....... : 0 (not enabled)
- CFG Lock........................... : 0 (MSR not locked)
- C3 State Auto Demotion............. : 0 (disabled/unsupported)
- C1 State Auto Demotion............. : 0 (disabled/unsupported)
- C3 State Undemotion................ : 0 (disabled/unsupported)
- C1 State Undemotion................ : 0 (disabled/unsupported)
- Package C-State Auto Demotion...... : 0 (disabled/unsupported)
- Package C-State Undemotion......... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE........(0xE4)  : 0x0
----------------------------------------
- LVL_2 Base Address................. : 0x0
- C-state Range...................... : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.....................(0xE7)  : 0x6F86AA83BA2
IA32_APERF.....................(0xE8)  : 0x7AAD2641271
MSR_0x150......................(0x150) : 0x0

MSR_FLEX_RATIO.................(0x194) : 0xE0000
----------------------------------------

MSR_IA32_PERF_STATUS...........(0x198) : 0x24E500002600
----------------------------------------
- Current Performance State Value.... : 0x2600

MSR_IA32_PERF_CONTROL..........(0x199) : 0x2600
----------------------------------------
- Target performance State Value..... : 0x2600
- Intel Dynamic Acceleration......... : 0 (IDA engaged)

IA32_CLOCK_MODULATION..........(0x19A) : 0x0
IA32_THERM_STATUS..............(0x19C) : 0x883E0000

IA32_MISC_ENABLES..............(0x1A0) : 0x810089
----------------------------------------
- Fast-Strings....................... : 1 (enabled)
- Automatic Thermal Control Circuit.. : 1 (enabled)
- Performance Monitoring............. : 1 (available)
- Enhanced Intel SpeedStep Technology : 1 (enabled)

MSR_MISC_PWR_MGMT..............(0x1AA) : 0x402000
----------------------------------------
- EIST Hardware Coordination......... : 0 (enabled)

MSR_TURBO_RATIO_LIMIT..........(0x1AD) : 0x2323262626262626
----------------------------------------
- Maximum Ratio Limit for C01........ : 38
- Maximum Ratio Limit for C02........ : 38
- Maximum Ratio Limit for C03........ : 38
- Maximum Ratio Limit for C04........ : 38
- Maximum Ratio Limit for C05........ : 38
- Maximum Ratio Limit for C06........ : 38

IA32_ENERGY_PERF_BIAS..........(0x1B0) : 0x0
----------------------------------------
- Power Policy Preference.............: 0 (highest performance)

MSR_POWER_CTL..................(0x1FC) : 0x2104005B
MSR_RAPL_POWER_UNIT............(0x606) : 0xA0E03
MSR_PKG_POWER_LIMIT............(0x610) : 0x7FFD00014EA82
MSR_PKG_ENERGY_STATUS..........(0x611) : 0x8C2989DA
MSR_PKG_POWER_INFO.............(0x614) : 0x1700460
MSR_PP0_POWER_LIMIT............(0x638) : 0x14FFD0
MSR_PP0_ENERGY_STATUS..........(0x639) : 0x0
MSR_TURBO_ACTIVATION_RATIO.....(0x64C) : 0x0
MSR_PKGC3_IRTL.................(0x60a) : 0x0
MSR_PKGC6_IRTL.................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY...........(0x60d) : 0x0
MSR_PKG_C3_RESIDENCY...........(0x3f8) : 0x0
MSR_PKG_C2_RESIDENCY...........(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY...........(0x3f9) : 0x0
IA32_TSC_DEADLINE..............(0x6E0) : 0x7F190854989

CPU Ratio Info:
----------------------------------------
CPU Maximum Efficiency Ratio...........: 1200 MHz
CPU Maximum non-Turbo Frequency........: 3400 MHz
CPU Maximum Turbo Frequency............: 3800 MHz
CPU P-States [ (38) ]
CPU P-States [ 37 (38) ]

Kexts used:

 

10.12 Folder

 

BrcmBluetoothInjector.kext

FakeSMC.kext

IntelMausiEthernet.kext

VoodooHDA.kext

X99_Injector USB 3.kext

 

drivers64UEFI folder

 

EmuVariableUefi-64.efi

FSInject-64.efi

HFSPlus.efi

OsxAptioFix2Drv-free2000.efi

OsxFatBinaryDrv-64.efi

 

Config.plist and current ssdt.aml attached

 

sysctl -n machdep.xcpm.mode = 0

 

sysctl -n machdep.xcpm.vectors_loaded_count = 0

 

From Pikeralphas blog:

 

 

Tips:

1.) The X86PlatformPlugin.kext will only load with the plugin-type property is set on the first logical CPU. This however is not enough to enable XCPM mode. No. You may still use AppleIntelCPUPowerManagement.kext Even when X86PlatformShim.kext is loaded.

2.) The FrequencyVectors data in the plist is used to configure power management, and is not the same for all models/board-ids. Please use one that works for your setup.

3.) If sysctl -n machdep.xcpm.vectors_loaded_count returns 0 then the FrequencyVectors data is not being used. Backup the plist for your board-id and replace it with a different plist.

4.) If you use ssdtPRGen.sh to generate your ssdt_pr.aml then make sure to use the -turbo [top-turbo-frequency] argument for overclocked setups.

5.) Check for XCPM related errors at boot time. Like this: X86PlatformShim::start – Failed to send stepper. You got to fix errors or things may not work properly.

 

I was pretty sure I patched the Frequency Vectors correctly using freqVectorsEdit.sh , but apparently not, i've tried manually copy the plist from different imacs to the macpro 6,1 manually and with the freqVectorsEdit.sh but to no avail.

 

any help at this point would be GREATLY appreciated

 

would someone be able to verify, make me a patch for 10.12 for the patch below, not sure if then i would be able t0 delete the FakeCPUID from clover then

 

(cpuid_set_info (OS X 10.11.6)

find 5D7F288D48BB83F902 replace 5D7F288D48B883F902

config.plist.zip

ssdt.aml.zip

Link to comment
Share on other sites

Kextstat Output:


Index Refs Address            Size       Wired      Name (Version) UUID <Linked Against>
    1   75 0xffffff7f80a46000 0x9d30     0x9d30     com.apple.kpi.bsd (16.0.0) E4FCD46F-29E4-48E0-AC80-09112759B74B
    2    8 0xffffff7f80dfe000 0x3940     0x3940     com.apple.kpi.dsep (16.0.0) 6E61102E-6F4C-427C-A260-752315F0D326
    3   96 0xffffff7f80a04000 0x21040    0x21040    com.apple.kpi.iokit (16.0.0) 4C73A787-459C-4202-ADC0-618E2AB040A1
    4  102 0xffffff7f80a26000 0xd200     0xd200     com.apple.kpi.libkern (16.0.0) 80845F3D-B38B-4D27-A667-09E01F9823B9
    5   88 0xffffff7f80a00000 0x3dd0     0x3dd0     com.apple.kpi.mach (16.0.0) ADCD3C1E-B06C-4671-BB6C-D0F2B1ED30F5
    6   50 0xffffff7f80a34000 0xb9c0     0xb9c0     com.apple.kpi.private (16.0.0) 9A8B0F6F-7DB0-4B11-AC22-7764DA290EC0
    7   67 0xffffff7f80a40000 0x5890     0x5890     com.apple.kpi.unsupported (16.0.0) 7963BC6B-45C1-448C-A4A1-F62DD7A32A0D
    8    6 0xffffff7f80e05000 0xa9000    0xa9000    com.apple.kec.corecrypto (1.0) 700E1192-8CD6-3F61-ABE9-D27C2CC1F164 <7 6 5 4 3 1>
    9    0 0xffffff7f80ef2000 0xf000     0xf000     com.apple.kec.pthread (1) 53A94F98-6C94-3094-93D1-30493115364E <7 6 5 4 1>
   10    1 0xffffff7f80f01000 0xb000     0xb000     com.apple.kec.Libm (1) 1441A2E9-3C13-3554-8028-F69175A80A5A <4>
   11   18 0xffffff7f80fef000 0x9000     0x9000     com.apple.iokit.IOACPIFamily (1.4) 4F7FB6AD-2498-3F71-827C-ED7AA4BF2511 <7 6 4 3>
   12   23 0xffffff7f80b32000 0x3a000    0x3a000    com.apple.iokit.IOPCIFamily (2.9) F6A129F7-5190-316B-9189-64CB2202D738 <7 6 5 4 3>
   13    1 0xffffff7f81dc6000 0x66000    0x66000    com.apple.driver.AppleACPIPlatform (5.0) D748FA50-380C-3F0D-BAD9-EB7A15848EA8 <12 11 7 6 5 4 3 1>
   14    1 0xffffff7f81168000 0xb000     0xb000     com.apple.driver.AppleFDEKeyStore (28.30) B9C62BFE-2AF9-33FF-85AD-B2BCEEF35E57 <8 7 6 5 4 3 1>
   15    3 0xffffff7f8152f000 0x7000     0x7000     com.apple.iokit.IOReportFamily (31) 3CAF0CDE-3EB5-32C8-91EF-EC5C7CAFBA22 <5 4 3>
   16    5 0xffffff7f80a50000 0x2f000    0x2f000    com.apple.iokit.IOStorageFamily (2.1) 1D78106B-791E-303B-9D12-FF31A942EB75 <7 6 5 4 3 1>
   17    0 0xffffff7f815b2000 0x1e000    0x1e000    com.apple.driver.DiskImages (444) 80D7E3BB-4F87-342C-B79E-77D9FDC33F2C <16 7 6 5 4 3 1>
   18    1 0xffffff7f81c36000 0x21000    0x21000    com.apple.driver.AppleCredentialManager (1.0) 74348615-A50D-3A32-B837-034444FDCBF6 <8 7 6 5 4 3 1>
   19    3 0xffffff7f80eae000 0x16000    0x16000    com.apple.driver.AppleMobileFileIntegrity (1.0.5) 9EF1435C-49FC-3B1D-8E32-605881F77C92 <8 7 6 5 4 3 2 1>
   20    0 0xffffff7f81c57000 0x3e000    0x3e000    com.apple.driver.AppleKeyStore (2) FDC7CCF4-944D-3CAB-A8C3-128FFBB16E5B <19 18 8 7 6 5 4 3 1>
   21    0 0xffffff7f81cf1000 0x2b000    0x2b000    com.apple.driver.AppleIntelCPUPowerManagement (219.0.0) 29E6C60B-0C1A-30B3-9982-3761305C188C <7 6 5 4 3 1>
   22    0 0xffffff7f81ec4000 0x11000    0x11000    org.netkas.driver.FakeSMC (1707) 72772B6B-84BC-3EC7-A053-FD8B95505F76 <11 7 5 4 3 1>
   23    0 0xffffff7f80e02000 0x2000     0x2000     com.apple.security.TMSafetyNet (8) 1CB512A3-24BD-344A-BFB4-44A61F27AB03 <7 6 5 4 2 1>
   24    2 0xffffff7f80ec4000 0x5000     0x5000     com.apple.kext.AppleMatch (1.0.0d1) 3B280DAB-903F-33DC-8110-525A1154B11E <4 1>
   25    1 0xffffff7f80ec9000 0x1f000    0x1f000    com.apple.security.sandbox (300.0) 0DB843E1-989D-35FB-8EED-722AAD25D8A4 <24 19 16 7 6 5 4 3 2 1>
   26    0 0xffffff7f80ee8000 0x9000     0x9000     com.apple.security.quarantine (3) 37B046F5-3150-34B0-A5FB-8DC85FC09589 <25 24 7 6 5 4 2 1>
   27    0 0xffffff7f81eba000 0x8000     0x8000     com.apple.nke.applicationfirewall (171) ED81F5E1-B4BC-3FC9-9335-C155DB430435 <7 6 5 4 3 1>
   28    0 0xffffff7f81cec000 0x3000     0x3000     com.apple.driver.AppleIntelCPUPowerManagementClient (219.0.0) B802638B-251C-3602-BA8C-001F87228765 <7 6 5 4 3 1>
   29    0 0xffffff7f81d94000 0x3000     0x3000     com.apple.driver.AppleAPIC (1.7) BC2E6D01-BCBB-3525-BF38-BF99C3F1EC46 <4 3>
   30    0 0xffffff7f81b89000 0x4000     0x4000     com.apple.driver.AppleSMBIOS (2.1) 9BB02681-4B47-3592-AD62-71FB0BF56965 <7 4 3>
   31    0 0xffffff7f81d58000 0x3000     0x3000     com.apple.driver.AppleHPET (1.8) 2CFB49B8-4CC2-320B-9C6E-99646DFD8571 <11 7 5 4 3>
   32    1 0xffffff7f81536000 0x5000     0x5000     com.apple.driver.AppleEFIRuntime (2.0) 6B7A5B9A-C313-3F7F-B6E2-60EE54593BC8 <7 6 5 4 3>
   33    0 0xffffff7f81bb6000 0x8000     0x8000     com.apple.driver.AppleRTC (2.0) 3FD1BCF4-8AFC-3CE6-A36E-26410544AD14 <11 5 4 3 1>
   34    3 0xffffff7f81173000 0x8d000    0x8d000    com.apple.iokit.IOHIDFamily (2.0.0) AE9ED6A0-B8C8-388A-9E5F-768B2B94CED5 <14 7 6 5 4 3 2 1>
   35    0 0xffffff7f81e36000 0x4000     0x4000     com.apple.driver.AppleACPIButtons (5.0) B40BC4E6-0A6A-3D4A-B534-84CEE779302B <34 15 13 11 7 6 5 4 3 1>
   36    1 0xffffff7f8153b000 0xb000     0xb000     com.apple.driver.AppleEFINVRAM (2.1) 6F4404D6-8625-35CA-AEB6-6ECD7B64FA52 <32 7 6 5 4 3 2 1>
   37    1 0xffffff7f80ff8000 0xd000     0xd000     com.apple.driver.AppleBusPowerController (1.0) 6A42D63F-510B-3A68-AB61-A6E6A2E34DB6 <11 5 4 3>
   38   11 0xffffff7f81005000 0x70000    0x70000    com.apple.iokit.IOUSBHostFamily (1.1) F46D940D-94E9-3B2F-BFC5-482D393178D5 <37 7 6 5 4 3 1>
   39    2 0xffffff7f810a9000 0xab000    0xab000    com.apple.iokit.IOUSBFamily (900.4.1) 8F6207EC-608D-373A-B35E-E6578202F58D <38 12 7 5 4 3 1>
   40    0 0xffffff7f81349000 0x5000     0x5000     com.apple.driver.usb.AppleUSBHostPacketFilter (1.0) 5B89B761-52AB-3592-8A02-FAA35F1BCC6B <38 7 6 5 4 3 1>
   41    3 0xffffff7f8157e000 0x34000    0x34000    com.apple.iokit.IONetworkingFamily (3.2) A75F754A-CFC1-381B-B99C-363B0FEAD5B5 <7 6 5 4 3 1>
   42    1 0xffffff7f816ea000 0x7000     0x7000     com.apple.filesystems.hfs.encodings.kext (1) 868F3029-68F7-38B3-BE10-2770ACAEB5D0 <7 6 5 4 3 1>
   43    0 0xffffff7f816f1000 0x69000    0x69000    com.apple.filesystems.hfs.kext (366) 33C570C6-7D79-31B6-A40C-4A3D81064EDE <42 7 6 5 4 3 1>
   44    0 0xffffff7f8185d000 0xa000     0xa000     com.apple.BootCache (39) 7F9AAFD7-4871-36F1-80CA-107A763017F1 <7 6 5 4 3 1>
   45    0 0xffffff7f81d72000 0x6000     0x6000     com.apple.AppleFSCompression.AppleFSCompressionTypeZlib (1.0.0) 9B32DDE9-151F-31A1-90E9-3CEB2C7BE27C <6 4 3 2 1>
   46    0 0xffffff7f81d7a000 0x3000     0x3000     com.apple.AppleFSCompression.AppleFSCompressionTypeDataless (1.0.0d1) C6F882D7-C35C-3963-A2FA-10033FF40107 <7 6 4 3 2 1>
   48    1 0xffffff7f8120b000 0x46000    0x46000    com.apple.driver.usb.AppleUSBXHCI (1.1) 6FA20ACA-149D-3D25-88E8-8A18BC3EDAEE <38 11 7 5 4 3 1>
   49    0 0xffffff7f81251000 0x2e000    0x2e000    com.apple.driver.usb.AppleUSBXHCIPCI (1.1) 486596CC-A5F0-39E7-BE14-782249E76C10 <48 38 12 11 7 5 4 3 1>
   50    0 0xffffff7f81ed5000 0x14000    0x14000    com.insanelymac.IntelMausiEthernet (2.1.0) D65691B8-4EB1-3B22-B1B5-5CA5C566935E <41 12 5 4 3 1>
   51    1 0xffffff7f8127f000 0x41000    0x41000    com.apple.driver.usb.AppleUSBEHCI (1.1) 1BB86D5F-65B2-3786-B8B7-FA48DD7817E8 <38 11 7 5 4 3 1>
   52    0 0xffffff7f8135e000 0x11000    0x11000    com.apple.driver.usb.AppleUSBEHCIPCI (1.1) BEBCB3AF-8A95-3F08-B694-44A3720BD56E <51 38 12 11 7 5 4 3 1>
   53    2 0xffffff7f81697000 0x1d000    0x1d000    com.apple.iokit.IOAHCIFamily (288) 5C275B66-A173-3D92-853A-44FC35D45FFC <5 4 3 1>
   54    0 0xffffff7f81d99000 0x1e000    0x1e000    com.apple.driver.AppleAHCIPort (326) F91BC44F-48CB-3348-AED0-9CAA6A9D7ECD <53 12 5 4 3 1>
   55    0 0xffffff7f81d6f000 0x2000     0x2000     net.osrom.kext.Disabler (1.0.1) 7D158CD9-D1C2-6ADC-D896-2FD8E29CD4AD <4 3>
   56    1 0xffffff7f8134e000 0x4000     0x4000     com.apple.driver.AppleUSBHostMergeProperties (1.1) F412AF0D-97E7-364A-A211-FF14F3972014 <4 3 1>
   57    0 0xffffff7f81396000 0x3000     0x3000     com.apple.driver.AppleUSBMergeNub (900.4.1) 1E7AC271-FB6C-33C6-9415-8007DA193D51 <56 39 4 3 1>
   58    0 0xffffff7f81546000 0x38000    0x38000    com.apple.iokit.IONVMeFamily (992.1.0) B460E2CE-D16E-3C0F-B41F-0E2A84FEB291 <36 19 16 15 12 7 6 5 4 3 1>
   59    2 0xffffff7f80f2f000 0x84000    0x84000    com.apple.iokit.IOFireWireFamily (4.6.4) 79AA2788-FEC3-3345-BC29-5BB4FF4F5814 <5 4 3 1>
   60    0 0xffffff7f81605000 0x26000    0x26000    com.apple.driver.AppleFWOHCI (5.5.5) 6EF0BC66-3AF8-3272-AE3A-E588FFB07BF7 <59 12 7 6 5 4 3 1>
   61    1 0xffffff7f813c4000 0x108000   0x108000   com.apple.iokit.IOThunderboltFamily (6.2.1) C6721C3B-DD22-3C13-98CC-1362A2DD761C <5 4 3 1>
   62    0 0xffffff7f81ac4000 0x22000    0x22000    com.apple.driver.AppleThunderboltNHI (4.1.3) FF1AD9A2-43B1-353B-B420-E7F7969DA742 <61 12 11 5 4 3 1>
   64    0 0xffffff7f816c1000 0x1c000    0x1c000    com.apple.iokit.IOAHCIBlockStorage (295.1.1) 08375C5A-FF97-32B5-8146-98192272C923 <53 16 6 5 4 3 1>
   65    0 0xffffff7f81313000 0x36000    0x36000    com.apple.driver.usb.AppleUSBHub (1.1) E9A2F12D-FE24-3838-85D7-8D665F3F61EF <38 11 5 4 3 1>
   66    0 0xffffff7f81352000 0x8000     0x8000     com.apple.driver.usb.AppleUSBHostCompositeDevice (1.1) 3465A4B1-B7B1-360A-B101-ECE555AFBE48 <38 5 4 3 1>
   67    0 0xffffff7f818ac000 0x8000     0x8000     com.apple.driver.usb.networking (5.0.0) BD6EEE30-3331-376B-A9F8-FA10A8F28731 <38 5 4 3 1>
   69    0 0xffffff7f80aef000 0x31000    0x31000    com.apple.iokit.IOSCSIArchitectureModelFamily (394) 0E35A335-5605-36FB-991C-D0D38F4FA4E7 <6 5 4 3 1>
   70    0 0xffffff7f81200000 0xb000     0xb000     com.apple.driver.usb.IOUSBHostHIDDevice (1.1) 302A8C57-3513-362E-BB6D-C17F7E93D7D7 <38 34 5 4 3 1>
   71    0 0xffffff7f8195d000 0xa000     0xa000     com.apple.driver.AppleHIDKeyboard (197) E03366C7-2F55-3D98-917A-39A349F4DAAA <34 5 4 3>
   72    1 0xffffff7f81ee9000 0x95000    0x95000    com.apple.vecLib.kext (1.2.0) 6ADA5F0B-10EF-360A-BF1E-E142D2074E4E <10 6 5 4 3>
   73    1 0xffffff7f81f7e000 0x30000    0x30000    com.apple.iokit.IOAudioFamily (205.11) BB1375FC-983D-3923-927F-88C0186414C8 <72 5 4 3 1>
   74    0 0xffffff7f81fae000 0x21000    0x21000    org.voodoo.driver.VoodooHDA (2.8.8) 394A3B95-68A8-326D-8980-BEC2B1C95048 <73 12 7 5 4 3>
   75    3 0xffffff7f81fcf000 0x8000     0x8000     com.apple.driver.IOPlatformPluginFamily (6.0.0d8) D211B7A8-7DC0-36DA-A6EE-BADF1F60162C <11 7 6 5 4 3>
   76    5 0xffffff7f81fd7000 0x19000    0x19000    com.apple.driver.AppleSMC (3.1.9) FA8E2E8A-FA5B-3949-AA1D-946DE5F5217B <11 7 5 4 3 1>
   77    1 0xffffff7f81ff0000 0x17000    0x17000    com.apple.driver.X86PlatformPlugin (1.0.0) F80CF40D-4ADE-3F20-AB94-B5EAB9B898E6 <76 75 39 38 11 7 6 5 4 3 1>
   78    0 0xffffff7f82007000 0x8000     0x8000     com.apple.driver.AppleIntelMCEReporter (107) 30B0E402-294F-332A-8386-F05E3EE170D9 <7 6 5 4 3>
   79    1 0xffffff7f814d0000 0x5000     0x5000     com.apple.iokit.IOSlowAdaptiveClockingFamily (1.0.0) F026208D-CC0C-3599-B303-9196904A584E <7 6 5 4 3 1>
   80    0 0xffffff7f8200f000 0x2000     0x2000     com.apple.driver.AppleIntelSlowAdaptiveClocking (4.0.0) 6FE984DD-A1FE-309E-83CF-B346989A6F17 <79 4 3>
   82    9 0xffffff7f82014000 0x3b000    0x3b000    com.apple.iokit.IOGraphicsFamily (2.4.1) 377FAA09-C02F-3FF4-A5DE-C0F2E711C8B0 <12 7 5 4 3 1>
   83    1 0xffffff7f814cc000 0x4000     0x4000     com.apple.iokit.IOSMBusFamily (1.1) 185F0EBF-0262-3370-BD47-8FE4C8AA726E <5 4 3>
   84    1 0xffffff7f8204f000 0xe000     0xe000     com.apple.driver.AppleSMBusController (1.0.14d1) 4DAA381E-3690-3E94-8025-DFB34F714094 <83 12 11 5 4 3>
   85    0 0xffffff7f8205d000 0xe000     0xe000     com.apple.driver.AppleMCCSControl (1.2.13) 102DD5D9-2DD5-3BCB-B5C0-BE08E1049CD6 <84 82 76 12 11 7 5 4 3 1>
   86    0 0xffffff7f8206b000 0xd000     0xd000     com.apple.iokit.IOFireWireIP (2.2.7) F30C2597-CAFD-386B-90E6-7A4007D8A6D5 <59 41 5 4 3 1>
   92    0 0xffffff7f820a5000 0x4000     0x4000     com.intel.driver.EnergyDriver (2.0) 4E0262A2-B79C-3386-8824-C106A5DFAF94 <7 5 4 3>
   94    5 0xffffff7f820ac000 0xe000     0xe000     com.apple.iokit.IONDRVSupport (2.4.1) C1544DFB-9066-340F-AD0A-9302DC3E6841 <82 12 7 5 4 3>
   95    1 0xffffff7f820ba000 0x5000     0x5000     com.apple.driver.AppleBacklightExpert (1.1.0) 7D89A61E-ED4E-32C7-8CC2-1D5B7E76E498 <94 82 76 12 5 4 3>
   96    0 0xffffff7f820bf000 0x5000     0x5000     com.apple.driver.AppleBacklight (170.9.10) 72AEF122-7C00-3F7A-AE4E-34495299E323 <95 94 82 12 5 4 3>
   97    0 0xffffff7f820c4000 0x4000     0x4000     com.apple.driver.AppleOSXWatchdog (1) 757A8B72-2A1A-32BA-99EC-6D802DE6E91F <12 7 6 5 4 3 1>
   98    0 0xffffff7f820c8000 0xa000     0xa000     com.apple.driver.AppleHV (1) 39AC9B9B-7B20-322F-82F0-044B3CC08D43 <7 6 5 4 3 1>
  101    1 0xffffff7f820e9000 0x7000     0x7000     com.apple.driver.X86PlatformShim (1.0.0) 4AAFC86D-5E06-31C5-A6C5-4F00C3A04F34 <77 76 75 7 4 3>
  102    2 0xffffff7f820f0000 0x9000     0x9000     com.apple.AppleGraphicsDeviceControl (3.13.60) FDEAB5E1-3BFF-34DF-92AB-6AE26C8405F7 <7 6 5 4 3 1>
  103    0 0xffffff7f820f9000 0x18000    0x18000    com.apple.driver.AGPM (110.23.7) E6276A25-70A0-366A-A935-2328CFA9226D <102 94 82 75 12 6 5 4 3>
  104    0 0xffffff7f82111000 0x4000     0x4000     com.apple.driver.ApplePlatformEnabler (2.7.0d0) 4B32012C-98E9-339A-A681-2A87EB353373 <7 5 4 3>
  105    0 0xffffff7f82115000 0x5000     0x5000     com.apple.Dont_Steal_Mac_OS_X (7.0.0) B97F871A-44FD-3EA4-BC46-8FD682118C79 <76 8 7 4 3 1>
  106    0 0xffffff7f8197c000 0xf3000    0xf3000    com.apple.iokit.IOBluetoothFamily (5.0.0f15) BBF19726-F609-3E2C-9FD3-A122539451C6 <15 7 5 4 3 1>
  107    2 0xffffff7f8211a000 0x326000   0x326000   com.nvidia.web.NVDAResmanWeb (10.1.3) 3EC6A9AA-1C98-3332-A7C8-6ED8383933FA <102 94 82 12 7 5 4 3 1>
  108    0 0xffffff7f82440000 0x1bd000   0x1bd000   com.nvidia.web.NVDAGK100HalWeb (10.1.3) 33C18CDB-ED78-304C-9841-E38CDA020F93 <107 12 4 3>
  109    1 0xffffff7f825fd000 0x90000    0x90000    com.apple.iokit.IOAcceleratorFamily2 (288.13) 27E0AFCE-E36A-35F5-A008-BB1EB3A2C7B9 <82 12 7 6 5 4 3 1>
  110    0 0xffffff7f8268d000 0x9a000    0x9a000    com.nvidia.web.GeForceWeb (10.1.3) 3081315F-E5BF-3CBF-862F-6E6F68D85615 <109 107 94 82 12 7 5 4 3 1>
  111    1 0xffffff7f82727000 0xe000     0xe000     com.apple.iokit.IOSerialFamily (11) B36990F3-B873-31BB-8A1B-5615A3277382 <7 6 5 4 3 1>
  112    0 0xffffff7f82735000 0xa000     0xa000     com.apple.iokit.IOBluetoothSerialManager (5.0.0f15) 85DBFB3F-95AE-39E9-AC65-16CFF31FE808 <111 7 5 4 3 1>
  113    0 0xffffff7f8273f000 0x5000     0x5000     com.apple.driver.AppleUpstreamUserClient (3.6.4) 761DD71A-0746-3515-A557-B702BBDD664A <82 12 11 7 5 4 3 1>
  114    0 0xffffff7f82744000 0x17000    0x17000    com.apple.iokit.IOSurface (152) CD2E7A07-1BD9-3298-A038-E6F8098F0C2A <7 6 5 4 3 1>
  115    0 0xffffff7f8275b000 0x6000     0x6000     com.apple.iokit.IOUserEthernet (1.0.1) 5EE448BD-95EC-35AD-B7FC-A1237E4BB346 <41 6 5 4 3 1>
  116    0 0xffffff7f82761000 0xd000     0xd000     com.apple.driver.pmtelemetry (1) E6E68296-809B-3884-ADEF-E85831F4B106 <7 6 5 4 3>
  117    2 0xffffff7f8276e000 0x5000     0x5000     com.apple.kext.triggers (1.0) 4E564246-8804-3673-B440-606AD360A3BB <7 6 5 4 3 1>
  118    0 0xffffff7f82773000 0x9000     0x9000     com.apple.filesystems.autofs (3.0) AA36D92F-D92B-3102-BAE3-F86A0A298143 <117 7 6 5 4 3 1>
  121    0 0xffffff7f8277c000 0x61000    0x61000    com.apple.filesystems.smbfs (3.1) 2D18A430-2FEB-31EB-9462-9CD093806F8B <117 8 7 6 5 4 3 1>
  122    1 0xffffff7f82078000 0xf000     0xf000     com.apple.filesystems.msdosfs (1.10) F8B8D309-C01A-32AD-B769-8822D9B4593B <7 5 4 1>
  123    0 0xffffff7f82087000 0x8000     0x8000     com.apple.driver.AppleXsanScheme (3) CE9B9375-DE2D-396A-9AB5-088FF26F081B <16 5 4 3 1>

Looks like applecpuintelpowermanagement is being used.

 

Maybe we have to find only a new reboot fix kernel patch for Broadwell E/EP cpu and Sierra (GM?)

 

 

Yes please!!!

 

 

Link to comment
Share on other sites

New Clover version has fixed my issues with XCPM, thanks to all involved with Clover and PikerAlpha for many fixes to get XCPM working on everyones machines :

 

AppleIntelInfo.kext v1.8 Copyright © 2012-2016 Pike R. Alpha. All rights reserved

 

Settings:

------------------------------------------

logMSRs..................................: 1

logIGPU..................................: 0

logCStates...............................: 1

logIPGStyle..............................: 1

InitialTSC...............................: 0x285838719d8 (81 MHz)

MWAIT C-States...........................: 8480

 

Processor Brandstring....................: Intel® Core i7-6800K CPU @ 3.40GHz

 

Processor Signature..................... : 0x406F1

------------------------------------------

 - Family............................... : 6

 - Stepping............................. : 1

 - Model................................ : 0x4F (79)

 

Model Specific Registers (MSRs)

------------------------------------------

 

MSR_CORE_THREAD_COUNT............(0x35)  : 0x6000C

------------------------------------------

 - Core Count........................... : 6

 - Thread Count......................... : 12

 

MSR_PLATFORM_INFO................(0xCE)  : 0x20080C3BF3812200

------------------------------------------

 - Maximum Non-Turbo Ratio.............. : 0x22 (3400 MHz)

 - Ratio Limit for Turbo Mode........... : 1 (programmable)

 - TDP Limit for Turbo Mode............. : 1 (programmable)

 - Low Power Mode Support............... : 1 (LPM supported)

 - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)

 - Maximum Efficiency Ratio............. : 12

 - Minimum Operating Ratio.............. : 8

 

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x403

------------------------------------------

 - I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)

 - CFG Lock............................. : 0 (MSR not locked)

 - C3 State Auto Demotion............... : 0 (disabled/unsupported)

 - C1 State Auto Demotion............... : 0 (disabled/unsupported)

 - C3 State Undemotion.................. : 0 (disabled/unsupported)

 - C1 State Undemotion.................. : 0 (disabled/unsupported)

 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)

 - Package C-State Undemotion........... : 0 (disabled/unsupported)

 

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414

------------------------------------------

 - LVL_2 Base Address................... : 0x414

 - C-state Range........................ : 1 (C6 is the max C-State to include)

 

IA32_MPERF.......................(0xE7)  : 0x11F721F962

IA32_APERF.......................(0xE8)  : 0x1094F7A244

MSR_0x150........................(0x150) : 0x52424

 

MSR_FLEX_RATIO...................(0x194) : 0xE0000

------------------------------------------

 

MSR_IA32_PERF_STATUS.............(0x198) : 0x226900002300

------------------------------------------

 - Current Performance State Value...... : 0x2300 (3500 MHz)

 

MSR_IA32_PERF_CONTROL............(0x199) : 0x2600

------------------------------------------

 - Target performance State Value....... : 0x2600 (3800 MHz)

 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

 

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x884E0000

 

IA32_MISC_ENABLES................(0x1A0) : 0x850089

------------------------------------------

 - Fast-Strings......................... : 1 (enabled)

 - Automatic Thermal Control Circuit.... : 1 (enabled)

 - Performance Monitoring............... : 1 (available)

 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)

 

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x640A00

------------------------------------------

 - Turbo Attenuation Units.............. : 0 

 - Temperature Target................... : 100

 - TCC Activation Offset................ : 0

 

MSR_MISC_PWR_MGMT................(0x1AA) : 0x402000

------------------------------------------

 - EIST Hardware Coordination........... : 0 (enabled)

 

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2323232323232626

------------------------------------------

 - Maximum Ratio Limit for C01.......... : 26 (3800 MHz) 

 - Maximum Ratio Limit for C02.......... : 26 (3800 MHz) 

 - Maximum Ratio Limit for C03.......... : 23 (3500 MHz) 

 - Maximum Ratio Limit for C04.......... : 23 (3500 MHz) 

 - Maximum Ratio Limit for C05.......... : 23 (3500 MHz) 

 - Maximum Ratio Limit for C06.......... : 23 (3500 MHz) 

 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x0

 

MSR_POWER_CTL....................(0x1FC) : 0x2104005B

------------------------------------------

 - C1E Enable............................: 1

 

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03

------------------------------------------

 - Power Units.......................... : 3 (1/8 Watt)

 - Energy Status Units.................. : 14 (61 micro-Joules)

 - Time Units .......................... : 10 (976.6 micro-Seconds)

 

MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82

------------------------------------------

 - Package Power Limit #1............... : 3408 Watt

 - Enable Power Limit #1................ : 1 (enabled)

 - Package Clamping Limitation #1....... : 0 (disabled)

 - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)

 - Package Power Limit #2............... : 4090 Watt

 - Enable Power Limit #2................ : 1 (enabled)

 - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)

 - Time Window for Power Limit #2....... : 3 (20 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PKG_ENERGY_STATUS............(0x611) : 0x3AC7B4E

------------------------------------------

 - Total Energy Consumed................ : 3761 Joules (Watt = Joules / seconds)

 

MSR_PKG_POWER_INFO...............(0x614) : 0x1700460

------------------------------------------

 - Thermal Spec Power................... : 140 Watt

 - Minimum Power........................ : 0

 - Maximum Power........................ : 0

 - Maximum Time Window.................. : 0

 

MSR_PP0_POWER_LIMIT..............(0x638) : 0x14FFD0

------------------------------------------

 - Power Limit.......................... : 4090 Watt

 - Enable Power Limit................... : 1 (enabled)

 - Clamping Limitation.................. : 0 (disabled)

 - Time Window for Power Limit.......... : 10 (10240 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PP0_ENERGY_STATUS............(0x639) : 0x0

 

MSR_TURBO_ACTIVATION_RATIO.......(0x64C) : 0x0

 

MSR_PKGC3_IRTL...................(0x60a) : 0x0

MSR_PKGC6_IRTL...................(0x60b) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x60FA75686

MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x60FA75686

MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x1580ECC93C

 

IA32_TSC_DEADLINE................(0x6E0) : 0x28587BD735C

 

CPU Ratio Info:

------------------------------------------

Base Clock Frequency (BLCK)............. : 100 MHz

Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)

Maximum non-Turbo Ratio/Frequency........: 34 (3400 MHz)

Maximum Turbo Ratio/Frequency............: 38 (3800 MHz)

P-State ratio * 100 = Frequency in MHz

------------------------------------------

CPU P-States [ (12) 30 35 ]

CPU C6-Cores [ 1 3 5 7 9 11 ]

CPU P-States [ 12 30 32 (34) 35 ]

CPU C6-Cores [ 0 1 2 3 4 5 7 8 9 11 ]

CPU P-States [ 12 22 30 32 (34) 35 ]

CPU P-States [ 12 22 30 31 32 34 (35) ]

CPU P-States [ (12) 22 28 30 31 32 34 35 ]

CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 11 ]

CPU P-States [ (12) 22 27 28 30 31 32 34 35 ]

CPU P-States [ 12 22 23 27 28 30 31 32 34 35 (36) ]

CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 ]

CPU P-States [ (12) 20 22 23 27 28 30 31 32 34 35 36 ]

CPU P-States [ (12) 20 22 23 24 27 28 30 31 32 34 35 36 ]

CPU P-States [ 12 20 22 23 24 26 27 28 30 31 32 (34) 35 36 ]

CPU P-States [ (12) 20 22 23 24 26 27 28 29 30 31 32 34 35 36 ]

CPU P-States [ 12 20 22 23 24 25 26 27 28 29 30 31 32 (34) 35 36 ]

CPU P-States [ 12 20 22 23 24 25 26 27 28 29 30 31 32 33 (34) 35 36 ]

CPU P-States [ (12) 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 ]

  • Like 2
Link to comment
Share on other sites

Last login: Wed Sep 21 11:40:41 on console
manoranjans-Pro:~ manoranjan$ sudo chown -R root:wheel /Users/manoranjan/Desktop/AppleIntelInfo.kext 
Password:
manoranjans-Pro:~ manoranjan$ sudo chmod -R 755 /Users/manoranjan/Desktop/AppleIntelInfo.kext 
manoranjans-Pro:~ manoranjan$ sudo kextload /Users/manoranjan/Desktop/AppleIntelInfo.kext 
manoranjans-Pro:~ manoranjan$ sudo cat /tmp/AppleIntelInfo.dat

AppleIntelInfo.kext v1.7 Copyright © 2012-2016 Pike R. Alpha. All rights reserved

Settings:
------------------------------------
logMSRs............................: 1
logIGPU............................: 0
logCStates.........................: 1
logIPGStyle........................: 1
InitialTSC.........................: 0x5c28d6b62c (13 MHz)
MWAIT C-States.....................: 8480

Processor Brandstring..................: Intel(R) Core(TM) i7-5960X CPU @ 3.00GHz

Processor Signature................... : 0x306F2
----------------------------------------
 - Family............................. : 6
 - Stepping........................... : 2
 - Model.............................. : 0x3F (63)

Model Specific Registers (MSRs)
---------------------------------------

MSR_CORE_THREAD_COUNT..........(0x35)  : 0x80010
----------------------------------------
 - Core Count......................... : 8
 - Thread Count....................... : 16

MSR_PLATFORM_INFO..............(0xCE)  : 0x80C3BF3811E00
----------------------------------------
 - Maximum Non-Turbo Ratio............ : 30
 - Ratio Limit for Turbo Mode......... : 1 (programmable)
 - TDP Limit for Turbo Mode........... : 1 (programmable)
 - Low Power Mode Support............. : 1 (LPM supported)
 - Number of ConfigTDP Levels......... : 1 (additional TDP level(s) available)
 - Maximum Efficiency Ratio........... : 12
 - Minimum Operating Ratio............ : 8

MSR_PMG_CST_CONFIG_CONTROL.....(0xE2)  : 0x3
----------------------------------------
 - I/O MWAIT Redirection Enable....... : 0 (not enabled)
 - CFG Lock........................... : 0 (MSR not locked)
 - C3 State Auto Demotion............. : 0 (disabled/unsupported)
 - C1 State Auto Demotion............. : 0 (disabled/unsupported)
 - C3 State Undemotion................ : 0 (disabled/unsupported)
 - C1 State Undemotion................ : 0 (disabled/unsupported)
 - Package C-State Auto Demotion...... : 0 (disabled/unsupported)
 - Package C-State Undemotion......... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE........(0xE4)  : 0x0
----------------------------------------
 - LVL_2 Base Address................. : 0x0
 - C-state Range...................... : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.....................(0xE7)  : 0xCDAE075BF
IA32_APERF.....................(0xE8)  : 0x11B424D226

MSR_FLEX_RATIO.................(0x194) : 0xE0000
----------------------------------------

MSR_IA32_PERF_STATUS...........(0x198) : 0x280400002B00
----------------------------------------
 - Current Performance State Value.... : 0x2B00 (4300 MHz)

MSR_IA32_PERF_CONTROL..........(0x199) : 0xFF00
----------------------------------------
 - Target performance State Value..... : 0xFF00 (25500 MHz)
 - Intel Dynamic Acceleration......... : 0 (IDA engaged)

IA32_CLOCK_MODULATION..........(0x19A) : 0x0
IA32_THERM_STATUS..............(0x19C) : 0x883E0000

IA32_MISC_ENABLES..............(0x1A0) : 0x850081
----------------------------------------
 - Fast-Strings....................... : 1 (enabled)
 - Automatic Thermal Control Circuit.. : 0 (disabled)
 - Performance Monitoring............. : 1 (available)
 - Enhanced Intel SpeedStep Technology : 1 (enabled)

MSR_MISC_PWR_MGMT..............(0x1AA) : 0x0
----------------------------------------
 - EIST Hardware Coordination......... : 0 (enabled)

MSR_TURBO_RATIO_LIMIT..........(0x1AD) : 0x2B2B2B2B2B2B2B2B
----------------------------------------
 - Maximum Ratio Limit for C01........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C02........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C03........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C04........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C05........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C06........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C07........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C08........ : 2B (4300 MHz) 

IA32_ENERGY_PERF_BIAS..........(0x1B0) : 0x5
----------------------------------------
 - Power Policy Preference.............: 5 (balanced performance and energy saving)

MSR_POWER_CTL..................(0x1FC) : 0x21040059
----------------------------------------

MSR_RAPL_POWER_UNIT............(0x606) : 0xA0E03
----------------------------------------
 - Power Units........................ : 3 (1/8 Watt)
 - Energy Status Units................ : 14 (61 micro-Joules)
 - Time Units ........................ : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT............(0x610) : 0x7FFD00014EA82
----------------------------------------
 - Package Power Limit #1............. : 3408 Watt
 - Enable Power Limit #1.............. : 1 (enabled)
 - Package Clamping Limitation #1..... : 0 (disabled)
 - Time Window for Power Limit #1..... : 10 (2560 milli-Seconds)
 - Package Power Limit #2............. : 4090 Watt
 - Enable Power Limit #2.............. : 1 (enabled)
 - Package Clamping Limitation #2..... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
 - Time Window for Power Limit #2..... : 3 (20 milli-Seconds)
 - Lock............................... : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS..........(0x611) : 0x286E6DE
----------------------------------------
 - Total Energy Consumed.............. : 2587 Joules (Watt = Joules / seconds)

MSR_PKG_POWER_INFO.............(0x614) : 0x1280460
----------------------------------------
 - Thermal Spec Power................. : 140 Watt
 - Minimum Power...................... : 0
 - Maximum Power...................... : 0
 - Maximum Time Window................ : 0

MSR_PP0_POWER_LIMIT............(0x638) : 0x14FFD0
----------------------------------------
 - Power Limit........................ : 4090 Watt
 - Enable Power Limit................. : 1 (enabled)
 - Clamping Limitation................ : 0 (disabled)
 - Time Window for Power Limit........ : 10 (10240 milli-Seconds)
 - Lock............................... : 0 (MSR not locked)

MSR_PP0_ENERGY_STATUS..........(0x639) : 0x0
----------------------------------------
 - Total Energy Consumed.............. : 0 Joules (Watt = Joules / seconds)

MSR_TURBO_ACTIVATION_RATIO.....(0x64C) : 0x0

MSR_CONFIG_TDP_NOMINAL.........(0x648) : 0x1E
MSR_CONFIG_TDP_LEVEL1..........(0x649) : 0x940000001B0460
MSR_CONFIG_TDP_LEVEL2..........(0x64a) : 0x94000000000000
MSR_CONFIG_TDP_CONTROL.........(0x64b) : 0x0
MSR_TURBO_ACTIVATION_RATIO.....(0x64c) : 0x0
MSR_PKGC6_IRTL.................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY...........(0x60d) : 0x15863BFDEE
MSR_PKG_C6_RESIDENCY...........(0x3f9) : 0x1434E9AB5E
IA32_TSC_DEADLINE..............(0x6E0) : 0x5C2BD7D543

CPU Ratio Info:
----------------------------------------
CPU Maximum Efficiency Ratio...........: 1200 MHz
CPU Maximum non-Turbo Frequency........: 3000 MHz
CPU Maximum Turbo Frequency............: 4300 MHz
CPU P-States [ 35 (43) ]
CPU C6-Cores [ 0 2 4 6 8 10 12 14 ]
CPU P-States [ 34 35 (43) ]
CPU P-States [ 34 35 41 (43) ]
CPU C6-Cores [ 0 2 4 5 6 8 10 12 14 ]
CPU C6-Cores [ 0 2 3 4 5 6 8 10 12 14 ]
CPU P-States [ 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 8 10 12 13 14 ]
CPU P-States [ 29 34 35 37 41 (43) ]
CPU P-States [ 28 29 34 35 37 41 (43) ]
CPU P-States [ 28 29 32 34 35 37 41 (43) ]
CPU P-States [ 28 29 31 32 34 35 37 41 (43) ]
CPU P-States [ (12) 28 29 31 32 33 34 35 37 41 43 ]
CPU P-States [ 12 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 8 9 10 12 13 14 ]
CPU P-States [ 12 23 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 7 8 9 10 12 13 14 ]
CPU P-States [ 12 23 25 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU P-States [ (12) 23 24 25 28 29 30 31 32 33 34 35 37 41 43 ]
manoranjans-Pro:~ manoranjan$ 

New Clover version has fixed my issues with XCPM, thanks to all involved with Clover and PikerAlpha for many fixes to get XCPM working on everyones machines :

 

AppleIntelInfo.kext v1.8 Copyright © 2012-2016 Pike R. Alpha. All rights reserved

 

Settings:

------------------------------------------

logMSRs..................................: 1

logIGPU..................................: 0

logCStates...............................: 1

logIPGStyle..............................: 1

InitialTSC...............................: 0x285838719d8 (81 MHz)

MWAIT C-States...........................: 8480

 

Processor Brandstring....................: Intel® Core i7-6800K CPU @ 3.40GHz

 

Processor Signature..................... : 0x406F1

------------------------------------------

 - Family............................... : 6

 - Stepping............................. : 1

 - Model................................ : 0x4F (79)

 

Model Specific Registers (MSRs)

------------------------------------------

IF you try this FakeCPUID  0x0406F1

Link to comment
Share on other sites

Last login: Wed Sep 21 11:40:41 on console
manoranjans-Pro:~ manoranjan$ sudo chown -R root:wheel /Users/manoranjan/Desktop/AppleIntelInfo.kext 
Password:
manoranjans-Pro:~ manoranjan$ sudo chmod -R 755 /Users/manoranjan/Desktop/AppleIntelInfo.kext 
manoranjans-Pro:~ manoranjan$ sudo kextload /Users/manoranjan/Desktop/AppleIntelInfo.kext 
manoranjans-Pro:~ manoranjan$ sudo cat /tmp/AppleIntelInfo.dat

AppleIntelInfo.kext v1.7 Copyright © 2012-2016 Pike R. Alpha. All rights reserved

Settings:
------------------------------------
logMSRs............................: 1
logIGPU............................: 0
logCStates.........................: 1
logIPGStyle........................: 1
InitialTSC.........................: 0x5c28d6b62c (13 MHz)
MWAIT C-States.....................: 8480

Processor Brandstring..................: Intel(R) Core(TM) i7-5960X CPU @ 3.00GHz

Processor Signature................... : 0x306F2
----------------------------------------
 - Family............................. : 6
 - Stepping........................... : 2
 - Model.............................. : 0x3F (63)

Model Specific Registers (MSRs)
---------------------------------------

MSR_CORE_THREAD_COUNT..........(0x35)  : 0x80010
----------------------------------------
 - Core Count......................... : 8
 - Thread Count....................... : 16

MSR_PLATFORM_INFO..............(0xCE)  : 0x80C3BF3811E00
----------------------------------------
 - Maximum Non-Turbo Ratio............ : 30
 - Ratio Limit for Turbo Mode......... : 1 (programmable)
 - TDP Limit for Turbo Mode........... : 1 (programmable)
 - Low Power Mode Support............. : 1 (LPM supported)
 - Number of ConfigTDP Levels......... : 1 (additional TDP level(s) available)
 - Maximum Efficiency Ratio........... : 12
 - Minimum Operating Ratio............ : 8

MSR_PMG_CST_CONFIG_CONTROL.....(0xE2)  : 0x3
----------------------------------------
 - I/O MWAIT Redirection Enable....... : 0 (not enabled)
 - CFG Lock........................... : 0 (MSR not locked)
 - C3 State Auto Demotion............. : 0 (disabled/unsupported)
 - C1 State Auto Demotion............. : 0 (disabled/unsupported)
 - C3 State Undemotion................ : 0 (disabled/unsupported)
 - C1 State Undemotion................ : 0 (disabled/unsupported)
 - Package C-State Auto Demotion...... : 0 (disabled/unsupported)
 - Package C-State Undemotion......... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE........(0xE4)  : 0x0
----------------------------------------
 - LVL_2 Base Address................. : 0x0
 - C-state Range...................... : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.....................(0xE7)  : 0xCDAE075BF
IA32_APERF.....................(0xE8)  : 0x11B424D226

MSR_FLEX_RATIO.................(0x194) : 0xE0000
----------------------------------------

MSR_IA32_PERF_STATUS...........(0x198) : 0x280400002B00
----------------------------------------
 - Current Performance State Value.... : 0x2B00 (4300 MHz)

MSR_IA32_PERF_CONTROL..........(0x199) : 0xFF00
----------------------------------------
 - Target performance State Value..... : 0xFF00 (25500 MHz)
 - Intel Dynamic Acceleration......... : 0 (IDA engaged)

IA32_CLOCK_MODULATION..........(0x19A) : 0x0
IA32_THERM_STATUS..............(0x19C) : 0x883E0000

IA32_MISC_ENABLES..............(0x1A0) : 0x850081
----------------------------------------
 - Fast-Strings....................... : 1 (enabled)
 - Automatic Thermal Control Circuit.. : 0 (disabled)
 - Performance Monitoring............. : 1 (available)
 - Enhanced Intel SpeedStep Technology : 1 (enabled)

MSR_MISC_PWR_MGMT..............(0x1AA) : 0x0
----------------------------------------
 - EIST Hardware Coordination......... : 0 (enabled)

MSR_TURBO_RATIO_LIMIT..........(0x1AD) : 0x2B2B2B2B2B2B2B2B
----------------------------------------
 - Maximum Ratio Limit for C01........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C02........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C03........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C04........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C05........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C06........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C07........ : 2B (4300 MHz) 
 - Maximum Ratio Limit for C08........ : 2B (4300 MHz) 

IA32_ENERGY_PERF_BIAS..........(0x1B0) : 0x5
----------------------------------------
 - Power Policy Preference.............: 5 (balanced performance and energy saving)

MSR_POWER_CTL..................(0x1FC) : 0x21040059
----------------------------------------

MSR_RAPL_POWER_UNIT............(0x606) : 0xA0E03
----------------------------------------
 - Power Units........................ : 3 (1/8 Watt)
 - Energy Status Units................ : 14 (61 micro-Joules)
 - Time Units ........................ : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT............(0x610) : 0x7FFD00014EA82
----------------------------------------
 - Package Power Limit #1............. : 3408 Watt
 - Enable Power Limit #1.............. : 1 (enabled)
 - Package Clamping Limitation #1..... : 0 (disabled)
 - Time Window for Power Limit #1..... : 10 (2560 milli-Seconds)
 - Package Power Limit #2............. : 4090 Watt
 - Enable Power Limit #2.............. : 1 (enabled)
 - Package Clamping Limitation #2..... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
 - Time Window for Power Limit #2..... : 3 (20 milli-Seconds)
 - Lock............................... : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS..........(0x611) : 0x286E6DE
----------------------------------------
 - Total Energy Consumed.............. : 2587 Joules (Watt = Joules / seconds)

MSR_PKG_POWER_INFO.............(0x614) : 0x1280460
----------------------------------------
 - Thermal Spec Power................. : 140 Watt
 - Minimum Power...................... : 0
 - Maximum Power...................... : 0
 - Maximum Time Window................ : 0

MSR_PP0_POWER_LIMIT............(0x638) : 0x14FFD0
----------------------------------------
 - Power Limit........................ : 4090 Watt
 - Enable Power Limit................. : 1 (enabled)
 - Clamping Limitation................ : 0 (disabled)
 - Time Window for Power Limit........ : 10 (10240 milli-Seconds)
 - Lock............................... : 0 (MSR not locked)

MSR_PP0_ENERGY_STATUS..........(0x639) : 0x0
----------------------------------------
 - Total Energy Consumed.............. : 0 Joules (Watt = Joules / seconds)

MSR_TURBO_ACTIVATION_RATIO.....(0x64C) : 0x0

MSR_CONFIG_TDP_NOMINAL.........(0x648) : 0x1E
MSR_CONFIG_TDP_LEVEL1..........(0x649) : 0x940000001B0460
MSR_CONFIG_TDP_LEVEL2..........(0x64a) : 0x94000000000000
MSR_CONFIG_TDP_CONTROL.........(0x64b) : 0x0
MSR_TURBO_ACTIVATION_RATIO.....(0x64c) : 0x0
MSR_PKGC6_IRTL.................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY...........(0x60d) : 0x15863BFDEE
MSR_PKG_C6_RESIDENCY...........(0x3f9) : 0x1434E9AB5E
IA32_TSC_DEADLINE..............(0x6E0) : 0x5C2BD7D543

CPU Ratio Info:
----------------------------------------
CPU Maximum Efficiency Ratio...........: 1200 MHz
CPU Maximum non-Turbo Frequency........: 3000 MHz
CPU Maximum Turbo Frequency............: 4300 MHz
CPU P-States [ 35 (43) ]
CPU C6-Cores [ 0 2 4 6 8 10 12 14 ]
CPU P-States [ 34 35 (43) ]
CPU P-States [ 34 35 41 (43) ]
CPU C6-Cores [ 0 2 4 5 6 8 10 12 14 ]
CPU C6-Cores [ 0 2 3 4 5 6 8 10 12 14 ]
CPU P-States [ 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 8 10 12 13 14 ]
CPU P-States [ 29 34 35 37 41 (43) ]
CPU P-States [ 28 29 34 35 37 41 (43) ]
CPU P-States [ 28 29 32 34 35 37 41 (43) ]
CPU P-States [ 28 29 31 32 34 35 37 41 (43) ]
CPU P-States [ (12) 28 29 31 32 33 34 35 37 41 43 ]
CPU P-States [ 12 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 8 9 10 12 13 14 ]
CPU P-States [ 12 23 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU C6-Cores [ 0 2 3 4 5 6 7 8 9 10 12 13 14 ]
CPU P-States [ 12 23 25 28 29 30 31 32 33 34 35 37 41 (43) ]
CPU P-States [ (12) 23 24 25 28 29 30 31 32 33 34 35 37 41 43 ]
manoranjans-Pro:~ manoranjan$ 

IF you try this FakeCPUID  0x0406F1

 

 

Weird didnt work have to use 0x040671 to get it to boot

Link to comment
Share on other sites

We all people with Broadwell E/ or xeon EP Cpu have all the same AppleIntelCpu output if xcpm is loaded and registered, and this is a fact also in ElCpaitan or in Sierra

Partial XCPM functionality

 

Low steps are not presents in Cpu P States from 13 to 17/18 and this behaviour is also evident with IPG (Intel Power Graphics)

So XCPM is under investigation and it is not fully working at this moment for unsupported CPU

 

 

this is a known issue, (i think all x99 booted with clover??) won´t stay at min. multiplier when CPU is idle. 

 

Pike R. Alpha showed some pictures from Intel Power Gadget, running Broadwell-E.

With this test system, X99 booted with Revoboot, the CPU seems to throttle correct.

 

I have done a lot of tests, but there is no solution to solve this problem. CPU jumps from min. to max. in idle.

 

And some interesting facts: you can boot with or without SSDT - i have always the same results. 

 

With patched and loaded Apple Intel CPU Powermanagement kext nothing changed.

 

I think something is wrong with the correct detection/setup for X99 CPUs with clover oder the fakesmc.

C-States and P-States are not correct in use.

 

But where to start investigation? 

  • Like 1
Link to comment
Share on other sites

Same here. Enable EIST = bad performance, but lower P-States.

 

When i look at the output from appleintelinfo.kext, i can see some strange settings:

 

EIST disabled in Bios, msr 0x1AA set to 400001

 

MSR_IA32_PERF_CONTROL............(0x199) : 0x7F00

------------------------------------------

- Target performance State Value....... : 0x7F00 (12700 MHz)

- Intel Dynamic Acceleration........... : 0 (IDA engaged)

 

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x884D0000

 

IA32_MISC_ENABLES................(0x1A0) : 0x840089

------------------------------------------

- Fast-Strings......................... : 1 (enabled)

- Automatic Thermal Control Circuit.... : 1 (enabled)

- Performance Monitoring............... : 1 (available)

- Enhanced Intel SpeedStep Technology.. : 0 (disabled)

 

MSR_MISC_PWR_MGMT................(0x1AA) : 0x400001

------------------------------------------

- EIST Hardware Coordination........... : 1 (disabled)

 

 

EIST disabled in Bios, and msr 0x1AA is set to 400000 i´m getting Target performance state values (msr0x199) from 1000 to 4800 MHz.

It changes every boot.

 

When i enable EIST (msr 0x1A0 set to 850089), the performance is very bad.

CPU don´t use the higher P-States and won´t stay at max. multi.

But then, the lower P-States are used.

 

 

Maybe… there is an error when xcpm/AICPM calculates and programs the msr/CPU frequencies.

 

But the same happens when i disable xcpm and use nullCpuPm kext. The CPU is jumping from min. multiplier to max. multiplier in idle mode, permanent from min to max.

Same results, tested with 2 motherboards (ASUS X-99 Deluxe and Gigabyte UD 5 WiFi).

  • Like 2
Link to comment
Share on other sites

this is my latest output from AppleIntelInfo.kext 1.8c:

 

AppleIntelInfo.kext v1.8c Copyright © 2012-2016 Pike R. Alpha. All rights reserved

 

Settings:

------------------------------------------

logMSRs..................................: 1

logIGPU..................................: 0

logCStates...............................: 1

logIPGStyle..............................: 1

InitialTSC...............................: 0x295fc19d766 (83 MHz)

MWAIT C-States...........................: 8480

 

Processor Brandstring....................: Intel® Core i7-6800K CPU @ 3.40GHz

 

Processor Signature..................... : 0x406F1

------------------------------------------

 - Family............................... : 6

 - Stepping............................. : 1

 - Model................................ : 0x4F (79)

 

Model Specific Registers (MSRs)

------------------------------------------

 

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF8070BE4D00

------------------------------------------

 - Core Count........................... : 6

 - Thread Count......................... : 12

 

MSR_PLATFORM_INFO................(0xCE)  : 0x20080C3BF3812200

------------------------------------------

 - Maximum Non-Turbo Ratio.............. : 0x22 (3400 MHz)

 - Ratio Limit for Turbo Mode........... : 1 (programmable)

 - TDP Limit for Turbo Mode............. : 1 (programmable)

 - Low Power Mode Support............... : 1 (LPM supported)

 - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)

 - Maximum Efficiency Ratio............. : 12

 - Minimum Operating Ratio.............. : 8

 

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x403

------------------------------------------

 - I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)

 - CFG Lock............................. : 0 (MSR not locked)

 - C3 State Auto Demotion............... : 0 (disabled/unsupported)

 - C1 State Auto Demotion............... : 0 (disabled/unsupported)

 - C3 State Undemotion.................. : 0 (disabled/unsupported)

 - C1 State Undemotion.................. : 0 (disabled/unsupported)

 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)

 - Package C-State Undemotion........... : 0 (disabled/unsupported)

 

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414

------------------------------------------

 - LVL_2 Base Address................... : 0x414

 - C-state Range........................ : 1 (C6 is the max C-State to include)

 

IA32_MPERF.......................(0xE7)  : 0x17D47033AF

IA32_APERF.......................(0xE8)  : 0x1497B0455D

MSR_0x150........................(0x150) : 0x0

 

MSR_FLEX_RATIO...................(0x194) : 0xE0000

------------------------------------------

 

MSR_IA32_PERF_STATUS.............(0x198) : 0x212D00002200

------------------------------------------

 - Current Performance State Value...... : 0x2200 (3400 MHz)

 

MSR_IA32_PERF_CONTROL............(0x199) : 0xC00

------------------------------------------

 - Target performance State Value....... : 0xC00 (1200 MHz)

 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

 

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x884E0000

 

IA32_MISC_ENABLES................(0x1A0) : 0x850089

------------------------------------------

 - Fast-Strings......................... : 1 (enabled)

 - Automatic Thermal Control Circuit.... : 1 (enabled)

 - Performance Monitoring............... : 1 (available)

 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)

 

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x640A00

------------------------------------------

 - Turbo Attenuation Units.............. : 0 

 - Temperature Target................... : 100

 - TCC Activation Offset................ : 0

 

MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000

------------------------------------------

 - EIST Hardware Coordination........... : 0 (enabled)

 

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2323232323232626

------------------------------------------

 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x0

 

MSR_POWER_CTL....................(0x1FC) : 0x2104005B

------------------------------------------

 - C1E Enable............................: 1

 

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03

------------------------------------------

 - Power Units.......................... : 3 (1/8 Watt)

 - Energy Status Units.................. : 14 (61 micro-Joules)

 - Time Units .......................... : 10 (976.6 micro-Seconds)

 

MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82

------------------------------------------

 - Package Power Limit #1............... : 3408 Watt

 - Enable Power Limit #1................ : 1 (enabled)

 - Package Clamping Limitation #1....... : 0 (disabled)

 - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)

 - Package Power Limit #2............... : 4090 Watt

 - Enable Power Limit #2................ : 1 (enabled)

 - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)

 - Time Window for Power Limit #2....... : 3 (20 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PKG_ENERGY_STATUS............(0x611) : 0x16914218

------------------------------------------

 - Total Energy Consumed................ : 23109 Joules (Watt = Joules / seconds)

 

MSR_PKG_POWER_INFO...............(0x614) : 0x1700460

------------------------------------------

 - Thermal Spec Power................... : 140 Watt

 - Minimum Power........................ : 0

 - Maximum Power........................ : 0

 - Maximum Time Window.................. : 0

 

MSR_PP0_POWER_LIMIT..............(0x638) : 0x14FFD0

------------------------------------------

 - Power Limit.......................... : 4090 Watt

 - Enable Power Limit................... : 1 (enabled)

 - Clamping Limitation.................. : 0 (disabled)

 - Time Window for Power Limit.......... : 10 (10240 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PP0_ENERGY_STATUS............(0x639) : 0x0

 

MSR_TURBO_ACTIVATION_RATIO.......(0x64C) : 0x0

 

MSR_PKGC3_IRTL...................(0x60a) : 0x0

MSR_PKGC6_IRTL...................(0x60b) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0

MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0

MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0

 

IA32_TSC_DEADLINE................(0x6E0) : 0x29600C48DAB

 

CPU Ratio Info:

------------------------------------------

Base Clock Frequency (BLCK)............. : 100 MHz

Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)

Maximum non-Turbo Ratio/Frequency........: 34 (3400 MHz)

Maximum Turbo Ratio/Frequency............: 38 (3800 MHz)

P-State ratio * 100 = Frequency in MHz

------------------------------------------

CPU P-States [ 30 34 (36) ]

CPU C6-Cores [ 2 5 6 8 11 ]

CPU P-States [ 30 34 35 (36) ]

CPU C6-Cores [ 2 4 5 6 8 9 10 11 ]

CPU C6-Cores [ 2 3 4 5 6 8 9 10 11 ]

CPU P-States [ 26 30 (34) 35 36 ]

CPU P-States [ 26 29 30 34 (35) 36 ]

CPU P-States [ (12) 26 29 30 34 35 36 ]

CPU C6-Cores [ 2 3 4 5 6 7 8 9 10 11 ]

CPU P-States [ 12 26 28 29 30 (34) 35 36 ]

CPU P-States [ 12 26 28 29 30 34 35 36 (38) ]

Link to comment
Share on other sites

@ekwipt

 

you have to stay more in idle and relaunch Appleintleinfo.kext

And if you can launch Geekbench test and then stay in idle

 

From your output seems that your cpu1 does not reach C6 states and this should not be good..

Maybe you have to stay more and relaunch the kext again

ok so it does make a big difference:

 

AppleIntelInfo.kext v1.8c Copyright © 2012-2016 Pike R. Alpha. All rights reserved

 

Settings:

------------------------------------------

logMSRs..................................: 1

logIGPU..................................: 0

logCStates...............................: 1

logIPGStyle..............................: 1

InitialTSC...............................: 0x295fc19d766 (83 MHz)

MWAIT C-States...........................: 8480

 

Processor Brandstring....................: Intel® Core i7-6800K CPU @ 3.40GHz

 

Processor Signature..................... : 0x406F1

------------------------------------------

 - Family............................... : 6

 - Stepping............................. : 1

 - Model................................ : 0x4F (79)

 

Model Specific Registers (MSRs)

------------------------------------------

 

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF8070BE4D00

------------------------------------------

 - Core Count........................... : 6

 - Thread Count......................... : 12

 

MSR_PLATFORM_INFO................(0xCE)  : 0x20080C3BF3812200

------------------------------------------

 - Maximum Non-Turbo Ratio.............. : 0x22 (3400 MHz)

 - Ratio Limit for Turbo Mode........... : 1 (programmable)

 - TDP Limit for Turbo Mode............. : 1 (programmable)

 - Low Power Mode Support............... : 1 (LPM supported)

 - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)

 - Maximum Efficiency Ratio............. : 12

 - Minimum Operating Ratio.............. : 8

 

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x403

------------------------------------------

 - I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)

 - CFG Lock............................. : 0 (MSR not locked)

 - C3 State Auto Demotion............... : 0 (disabled/unsupported)

 - C1 State Auto Demotion............... : 0 (disabled/unsupported)

 - C3 State Undemotion.................. : 0 (disabled/unsupported)

 - C1 State Undemotion.................. : 0 (disabled/unsupported)

 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)

 - Package C-State Undemotion........... : 0 (disabled/unsupported)

 

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414

------------------------------------------

 - LVL_2 Base Address................... : 0x414

 - C-state Range........................ : 1 (C6 is the max C-State to include)

 

IA32_MPERF.......................(0xE7)  : 0x17D47033AF

IA32_APERF.......................(0xE8)  : 0x1497B0455D

MSR_0x150........................(0x150) : 0x0

 

MSR_FLEX_RATIO...................(0x194) : 0xE0000

------------------------------------------

 

MSR_IA32_PERF_STATUS.............(0x198) : 0x212D00002200

------------------------------------------

 - Current Performance State Value...... : 0x2200 (3400 MHz)

 

MSR_IA32_PERF_CONTROL............(0x199) : 0xC00

------------------------------------------

 - Target performance State Value....... : 0xC00 (1200 MHz)

 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

 

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x884E0000

 

IA32_MISC_ENABLES................(0x1A0) : 0x850089

------------------------------------------

 - Fast-Strings......................... : 1 (enabled)

 - Automatic Thermal Control Circuit.... : 1 (enabled)

 - Performance Monitoring............... : 1 (available)

 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)

 

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x640A00

------------------------------------------

 - Turbo Attenuation Units.............. : 0 

 - Temperature Target................... : 100

 - TCC Activation Offset................ : 0

 

MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000

------------------------------------------

 - EIST Hardware Coordination........... : 0 (enabled)

 

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2323232323232626

------------------------------------------

 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x0

 

MSR_POWER_CTL....................(0x1FC) : 0x2104005B

------------------------------------------

 - C1E Enable............................: 1

 

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03

------------------------------------------

 - Power Units.......................... : 3 (1/8 Watt)

 - Energy Status Units.................. : 14 (61 micro-Joules)

 - Time Units .......................... : 10 (976.6 micro-Seconds)

 

MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82

------------------------------------------

 - Package Power Limit #1............... : 3408 Watt

 - Enable Power Limit #1................ : 1 (enabled)

 - Package Clamping Limitation #1....... : 0 (disabled)

 - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)

 - Package Power Limit #2............... : 4090 Watt

 - Enable Power Limit #2................ : 1 (enabled)

 - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)

 - Time Window for Power Limit #2....... : 3 (20 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PKG_ENERGY_STATUS............(0x611) : 0x16914218

------------------------------------------

 - Total Energy Consumed................ : 23109 Joules (Watt = Joules / seconds)

 

MSR_PKG_POWER_INFO...............(0x614) : 0x1700460

------------------------------------------

 - Thermal Spec Power................... : 140 Watt

 - Minimum Power........................ : 0

 - Maximum Power........................ : 0

 - Maximum Time Window.................. : 0

 

MSR_PP0_POWER_LIMIT..............(0x638) : 0x14FFD0

------------------------------------------

 - Power Limit.......................... : 4090 Watt

 - Enable Power Limit................... : 1 (enabled)

 - Clamping Limitation.................. : 0 (disabled)

 - Time Window for Power Limit.......... : 10 (10240 milli-Seconds)

 - Lock................................. : 0 (MSR not locked)

 

MSR_PP0_ENERGY_STATUS............(0x639) : 0x0

 

MSR_TURBO_ACTIVATION_RATIO.......(0x64C) : 0x0

 

MSR_PKGC3_IRTL...................(0x60a) : 0x0

MSR_PKGC6_IRTL...................(0x60b) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0

MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0

MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0

MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0

 

IA32_TSC_DEADLINE................(0x6E0) : 0x29600C48DAB

 

CPU Ratio Info:

------------------------------------------

Base Clock Frequency (BLCK)............. : 100 MHz

Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)

Maximum non-Turbo Ratio/Frequency........: 34 (3400 MHz)

Maximum Turbo Ratio/Frequency............: 38 (3800 MHz)

P-State ratio * 100 = Frequency in MHz

------------------------------------------

CPU P-States [ 30 34 (36) ]

CPU C6-Cores [ 2 5 6 8 11 ]

CPU P-States [ 30 34 35 (36) ]

CPU C6-Cores [ 2 4 5 6 8 9 10 11 ]

CPU C6-Cores [ 2 3 4 5 6 8 9 10 11 ]

CPU P-States [ 26 30 (34) 35 36 ]

CPU P-States [ 26 29 30 34 (35) 36 ]

CPU P-States [ (12) 26 29 30 34 35 36 ]

CPU C6-Cores [ 2 3 4 5 6 7 8 9 10 11 ]

CPU P-States [ 12 26 28 29 30 (34) 35 36 ]

CPU P-States [ 12 26 28 29 30 34 35 36 (38) ]

CPU P-States [ 12 26 28 29 30 32 34 35 36 (38) ]

CPU P-States [ 12 26 28 29 30 31 32 34 35 36 (38) ]

CPU P-States [ (12) 26 27 28 29 30 31 32 34 35 36 38 ]

CPU P-States [ 12 25 26 27 28 29 30 31 32 34 35 (36) 38 ]

CPU P-States [ 12 21 25 26 27 28 29 30 31 32 (34) 35 36 38 ]

CPU P-States [ (12) 21 22 25 26 27 28 29 30 31 32 34 35 36 38 ]

CPU P-States [ (12) 19 21 22 25 26 27 28 29 30 31 32 34 35 36 38 ]

CPU P-States [ (12) 19 21 22 23 25 26 27 28 29 30 31 32 34 35 36 38 ]

CPU P-States [ 12 17 19 21 22 23 25 26 27 28 29 30 31 32 34 (35) 36 38 ]

CPU P-States [ 12 17 19 21 22 23 24 25 26 27 28 29 30 31 32 (34) 35 36 38 ]

CPU P-States [ 12 17 19 21 22 23 24 25 26 27 28 29 30 31 32 33 34 (35) 36 38 ]

CPU P-States [ 12 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 (36) 38 ]

CPU P-States [ 12 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 (35) 36 38 ]

CPU P-States [ (12) 14 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38 ]

CPU P-States [ (12) 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38 ]

CPU P-States [ (12) 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38 ]

CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 (35) 36 38 ]

Link to comment
Share on other sites

on c6 states seems to be it a problem

but P-States are perfect if you have good performance and eist disabled on bios

 

I don't really understand what i'm seeing Fabiosun, but thanks for looking, my geekbench scores are all over the place, i use to have over 20000 multicore scores, anyway...

post-91745-0-34268700-1475157498_thumb.png

post-91745-0-87559500-1475157507_thumb.png

post-91745-0-16435000-1475157519_thumb.png

Link to comment
Share on other sites

Do any of you gys have drop tables in your config, i really don't know what they are used for?

 

<key>ACPI</key>
<dict>
<key>DSDT</key>
<dict>
<key>Debug</key>
<false/>
<key>DropOEM_DSM</key>
<false/>
<key>Name</key>
<string>DSDT.aml</string>
<key>ReuseFFFF</key>
<false/>
</dict>
<key>DropTables</key>
<array>
<dict>
<key>Signature</key>
<string>DMAR</string>
</dict>
<dict>
<key>Signature</key>
<string>SSDT</string>
<key>TableId</key>
<string>Cpu0Ist</string>
</dict>
<dict>
<key>Signature</key>
<string>SSDT</string>
<key>TableId</key>
<string>CpuPm</string>
</dict>
</array>
<key>SSDT</key>
<dict>
<key>DropOem</key>
<false/>
<key>Generate</key>
<false/>
</dict>
<key>smartUPS</key>
<true/>
</dict>

Look here from your output

 

- Enhanced Intel SpeedStep Technology.. : 1 (enabled)

 

you have speedstep in your bios enabled so you have same problem we all have

 

 

try to disable and you should see best multi cpu core score and you will see to disappear all lower state when you check with Pike's appleintelinfo kext

 

ok thanks Fabiosum, do you think this will help me in "real world situation"? I'm mainly using the rig for Audio DAW work with Ableton Live and doing some editing in Premiere and FX work in After Effetc?? 

Link to comment
Share on other sites

@ekwipt

I see you have my same problem with MSR PKG POWER LIMIT....value is high...and as suggested by Piker we should try to set not in AUTO some bios parameters....

 

MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82

------------------------------------------

 - Package Power Limit #1............... : 3408 Watt

 - Enable Power Limit #1................ : 1 (enabled)

 - Package Clamping Limitation #1....... : 0 (disabled)

 - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)

 - Package Power Limit #2............... : 4090 Watt

Link to comment
Share on other sites

  • 4 months later...

We all people with Broadwell E/ or xeon EP Cpu have all the same AppleIntelCpu output if xcpm is loaded and registered, and this is a fact also in ElCpaitan or in Sierra

Partial XCPM functionality

 

Low steps are not presents in Cpu P States from 13 to 17/18 and this behaviour is also evident with IPG (Intel Power Gadget)

So XCPM is under investigation and it is not fully working at this moment for unsupported CPU

 

 

@ekwipt

with your cpu you can try to use fakecpuid that you are using or use 2,3,4 for last digit (one of those digits)

But not xcpm difference at all in my case

Is this still an issue with Haswell-E chips? I have Xeon E5-2630v3 and I'm having tons of problems getting XCPM to work.

 

To my knowledge I'm using all the pike patches in clover for Haswell-E and have the xcpm bootflag enabled and did freq vectors for a 14,2 (I believe.)

 

This is my kext output:

AppleIntelInfo.kext v2.0 Copyright © 2012-2016 Pike R. Alpha. All rights reserved
enableHWP................................: 0

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 0
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0x2f863eba990 (136 MHz)
MWAIT C-States...........................: 8480

Processor Brandstring....................: Intel(R) Xeon(R) CPU E5-2630 v3 @ 2.40GHz

Processor Signature..................... : 0x306F2
------------------------------------------
- Family............................... : 6
- Stepping............................. : 2
- Model................................ : 0x3F (63)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF806BBFC400
------------------------------------------
- Core Count........................... : 8
- Thread Count......................... : 16

MSR_PLATFORM_INFO................(0xCE)  : 0x80C33F3811800
------------------------------------------
- Maximum Non-Turbo Ratio.............. : 0x18 (2400 MHz)
- Ratio Limit for Turbo Mode........... : 1 (programmable)
- TDP Limit for Turbo Mode............. : 1 (programmable)
- Low Power Mode Support............... : 1 (LPM supported)
- Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)
- Maximum Efficiency Ratio............. : 12
- Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x8400
------------------------------------------
- I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)
- CFG Lock............................. : 1 (MSR locked until next reset)
- C3 State Auto Demotion............... : 0 (disabled/unsupported)
- C1 State Auto Demotion............... : 0 (disabled/unsupported)
- C3 State Undemotion.................. : 0 (disabled/unsupported)
- C1 State Undemotion.................. : 0 (disabled/unsupported)
- Package C-State Auto Demotion........ : 0 (disabled/unsupported)
- Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414
------------------------------------------
- LVL_2 Base Address................... : 0x414
- C-state Range........................ : 1 (C6 is the max C-State to include)

IA32_MPERF.......................(0xE7)  : 0x94290EC077
IA32_APERF.......................(0xE8)  : 0x3C757B3C6E

MSR_FLEX_RATIO...................(0x194) : 0x0
------------------------------------------

MSR_IA32_PERF_STATUS.............(0x198) : 0x1A7700001800
------------------------------------------
- Current Performance State Value...... : 0x1800 (2400 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0xC00
------------------------------------------
- Target performance State Value....... : 0xC00 (1200 MHz)
- Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x88350000
------------------------------------------
- Thermal Status....................... : 0
- Thermal Log.......................... : 0
- PROCHOT # or FORCEPR# event.......... : 0
- PROCHOT # or FORCEPR# log............ : 0
- Critical Temperature Status.......... : 0
- Critical Temperature log............. : 0
- Thermal Threshold #1 Status.......... : 0
- Thermal Threshold #1 log............. : 0
- Thermal Threshold #2 Status.......... : 0
- Thermal Threshold #2 log............. : 0
- Power Limitation Status.............. : 0
- Power Limitation log................. : 0
- Current Limit Status................. : 0
- Current Limit log.................... : 0
- Cross Domain Limit Status............ : 0
- Cross Domain Limit log............... : 0
- Digital Readout...................... : 53
- Resolution in Degrees Celsius........ : 1
- Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
- Fast-Strings......................... : 1 (enabled)
- FOPCODE compatibility mode Enable.... : 0
- Automatic Thermal Control Circuit.... : 1 (enabled)
- Split-lock Disable................... : 0
- Performance Monitoring............... : 1 (available)
- Bus Lock On Cache Line Splits Disable : 0
- Hardware prefetch Disable............ : 0
- Processor Event Based Sampling....... : 0 (PEBS supported)
- GV1/2 legacy Enable.................. : 0
- Enhanced Intel SpeedStep Technology.. : 1 (enabled)
- MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
- Adjacent sector prefetch Disable..... : 0
- CFG Lock............................. : 0 (MSR not locked)
- xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x570A00
------------------------------------------
- Turbo Attenuation Units.............. : 0
- Temperature Target................... : 87
- TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000
------------------------------------------
- EIST Hardware Coordination........... : 0 (hardware coordination enabled)
- Energy/Performance Bias support...... : 1
- Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
- Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x1A1A1B1C1D1E2020
------------------------------------------
- Maximum Ratio Limit for C01.......... : 20 (3200 MHz)
- Maximum Ratio Limit for C02.......... : 20 (3200 MHz)
- Maximum Ratio Limit for C03.......... : 1E (3000 MHz)
- Maximum Ratio Limit for C04.......... : 1D (2900 MHz)
- Maximum Ratio Limit for C05.......... : 1C (2800 MHz)
- Maximum Ratio Limit for C06.......... : 1B (2700 MHz)
- Maximum Ratio Limit for C07.......... : 1A (2600 MHz)
- Maximum Ratio Limit for C08.......... : 1A (2600 MHz)

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
- Power Policy Preference...............: 1 (highest performance)

MSR_POWER_CTL....................(0x1FC) : 0x2904005B
------------------------------------------
- Bi-Directional Processor Hot..........: 1 (enabled)
- C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
- Power Units.......................... : 3 (1/8 Watt)
- Energy Status Units.................. : 14 (61 micro-Joules)
- Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x78330001582A8
------------------------------------------
- Package Power Limit #1............... : 85 Watt
- Enable Power Limit #1................ : 1 (enabled)
- Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
- Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)
- Package Power Limit #2............... : 102 Watt
- Enable Power Limit #2................ : 1 (enabled)
- Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
- Time Window for Power Limit #2....... : 3 (20 milli-Seconds)
- Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0x15972FCE
------------------------------------------
- Total Energy Consumed................ : 22108 Joules (Watt = Joules / seconds)

MSR_PKG_POWER_INFO...............(0x614) : 0x2F0550014002A8
------------------------------------------
- Thermal Spec Power................... : 85 Watt
- Minimum Power........................ : 0
- Maximum Power........................ : 170
- Maximum Time Window.................. : 0

MSR_PP0_POWER_LIMIT..............(0x638) : 0x0

MSR_PP0_ENERGY_STATUS............(0x639) : 0x0

MSR_TURBO_ACTIVATION_RATIO.......(0x64C) : 0x0

MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x18
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0xA00550001502A8
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0xA0055000000000
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x0
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0

IA32_TSC_DEADLINE................(0x6E0) : 0x2F867CA02C8

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)
Maximum non-Turbo Ratio/Frequency........: 24 (2400 MHz)
Maximum Turbo Ratio/Frequency............: 32 (3200 MHz)
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (12) 23 ]
CPU C6-Cores [ 0 2 4 6 8 10 12 14 ]
CPU P-States [ (12) 16 23 ]
CPU C6-Cores [ 0 2 3 4 6 8 9 10 12 14 15 ]
CPU P-States [ (12) 16 18 23 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 14 15 ]
CPU P-States [ (12) 16 17 18 23 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 13 14 15 ]
CPU P-States [ 12 16 17 18 19 23 (24) ]
CPU P-States [ (12) 16 17 18 19 20 23 24 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 11 12 13 14 15 ]
CPU P-States [ (12) 16 17 18 19 20 22 23 24 ]
CPU P-States [ (12) 14 16 17 18 19 20 22 23 24 ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
CPU P-States [ (12) 14 16 17 18 19 20 21 22 23 24 ]
CPU P-States [ (12) 14 15 16 17 18 19 20 21 22 23 24 ]
CPU P-States [ 12 14 15 16 17 18 19 20 21 22 23 24 (32) ]

any ideas what could be wrong, anyone?

 

10.12.2.

 

Thanks

Link to comment
Share on other sites

Is this still an issue with Haswell-E chips? I have Xeon E5-2630v3 and I'm having tons of problems getting XCPM to work.

 

To my knowledge I'm using all the pike patches in clover for Haswell-E and have the xcpm bootflag enabled and did freq vectors for a 14,2 (I believe.)

 

This is my kext output:

AppleIntelInfo.kext v2.0 Copyright © 2012-2016 Pike R. Alpha. All rights reserved
enableHWP................................: 0

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 0
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0x2f863eba990 (136 MHz)
MWAIT C-States...........................: 8480

Processor Brandstring....................: Intel(R) Xeon(R) CPU E5-2630 v3 @ 2.40GHz

Processor Signature..................... : 0x306F2
------------------------------------------
- Family............................... : 6
- Stepping............................. : 2
- Model................................ : 0x3F (63)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF806BBFC400
------------------------------------------
- Core Count........................... : 8
- Thread Count......................... : 16

MSR_PLATFORM_INFO................(0xCE)  : 0x80C33F3811800
------------------------------------------
- Maximum Non-Turbo Ratio.............. : 0x18 (2400 MHz)
- Ratio Limit for Turbo Mode........... : 1 (programmable)
- TDP Limit for Turbo Mode............. : 1 (programmable)
- Low Power Mode Support............... : 1 (LPM supported)
- Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)
- Maximum Efficiency Ratio............. : 12
- Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x8400
------------------------------------------
- I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)
- CFG Lock............................. : 1 (MSR locked until next reset)
- C3 State Auto Demotion............... : 0 (disabled/unsupported)
- C1 State Auto Demotion............... : 0 (disabled/unsupported)
- C3 State Undemotion.................. : 0 (disabled/unsupported)
- C1 State Undemotion.................. : 0 (disabled/unsupported)
- Package C-State Auto Demotion........ : 0 (disabled/unsupported)
- Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414
------------------------------------------
- LVL_2 Base Address................... : 0x414
- C-state Range........................ : 1 (C6 is the max C-State to include)

IA32_MPERF.......................(0xE7)  : 0x94290EC077
IA32_APERF.......................(0xE8)  : 0x3C757B3C6E

MSR_FLEX_RATIO...................(0x194) : 0x0
------------------------------------------

MSR_IA32_PERF_STATUS.............(0x198) : 0x1A7700001800
------------------------------------------
- Current Performance State Value...... : 0x1800 (2400 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0xC00
------------------------------------------
- Target performance State Value....... : 0xC00 (1200 MHz)
- Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x88350000
------------------------------------------
- Thermal Status....................... : 0
- Thermal Log.......................... : 0
- PROCHOT # or FORCEPR# event.......... : 0
- PROCHOT # or FORCEPR# log............ : 0
- Critical Temperature Status.......... : 0
- Critical Temperature log............. : 0
- Thermal Threshold #1 Status.......... : 0
- Thermal Threshold #1 log............. : 0
- Thermal Threshold #2 Status.......... : 0
- Thermal Threshold #2 log............. : 0
- Power Limitation Status.............. : 0
- Power Limitation log................. : 0
- Current Limit Status................. : 0
- Current Limit log.................... : 0
- Cross Domain Limit Status............ : 0
- Cross Domain Limit log............... : 0
- Digital Readout...................... : 53
- Resolution in Degrees Celsius........ : 1
- Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
- Fast-Strings......................... : 1 (enabled)
- FOPCODE compatibility mode Enable.... : 0
- Automatic Thermal Control Circuit.... : 1 (enabled)
- Split-lock Disable................... : 0
- Performance Monitoring............... : 1 (available)
- Bus Lock On Cache Line Splits Disable : 0
- Hardware prefetch Disable............ : 0
- Processor Event Based Sampling....... : 0 (PEBS supported)
- GV1/2 legacy Enable.................. : 0
- Enhanced Intel SpeedStep Technology.. : 1 (enabled)
- MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
- Adjacent sector prefetch Disable..... : 0
- CFG Lock............................. : 0 (MSR not locked)
- xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x570A00
------------------------------------------
- Turbo Attenuation Units.............. : 0
- Temperature Target................... : 87
- TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000
------------------------------------------
- EIST Hardware Coordination........... : 0 (hardware coordination enabled)
- Energy/Performance Bias support...... : 1
- Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
- Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x1A1A1B1C1D1E2020
------------------------------------------
- Maximum Ratio Limit for C01.......... : 20 (3200 MHz)
- Maximum Ratio Limit for C02.......... : 20 (3200 MHz)
- Maximum Ratio Limit for C03.......... : 1E (3000 MHz)
- Maximum Ratio Limit for C04.......... : 1D (2900 MHz)
- Maximum Ratio Limit for C05.......... : 1C (2800 MHz)
- Maximum Ratio Limit for C06.......... : 1B (2700 MHz)
- Maximum Ratio Limit for C07.......... : 1A (2600 MHz)
- Maximum Ratio Limit for C08.......... : 1A (2600 MHz)

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
- Power Policy Preference...............: 1 (highest performance)

MSR_POWER_CTL....................(0x1FC) : 0x2904005B
------------------------------------------
- Bi-Directional Processor Hot..........: 1 (enabled)
- C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
- Power Units.......................... : 3 (1/8 Watt)
- Energy Status Units.................. : 14 (61 micro-Joules)
- Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x78330001582A8
------------------------------------------
- Package Power Limit #1............... : 85 Watt
- Enable Power Limit #1................ : 1 (enabled)
- Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
- Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)
- Package Power Limit #2............... : 102 Watt
- Enable Power Limit #2................ : 1 (enabled)
- Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
- Time Window for Power Limit #2....... : 3 (20 milli-Seconds)
- Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0x15972FCE
------------------------------------------
- Total Energy Consumed................ : 22108 Joules (Watt = Joules / seconds)

MSR_PKG_POWER_INFO...............(0x614) : 0x2F0550014002A8
------------------------------------------
- Thermal Spec Power................... : 85 Watt
- Minimum Power........................ : 0
- Maximum Power........................ : 170
- Maximum Time Window.................. : 0

MSR_PP0_POWER_LIMIT..............(0x638) : 0x0

MSR_PP0_ENERGY_STATUS............(0x639) : 0x0

MSR_TURBO_ACTIVATION_RATIO.......(0x64C) : 0x0

MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x18
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0xA00550001502A8
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0xA0055000000000
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x0
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0

IA32_TSC_DEADLINE................(0x6E0) : 0x2F867CA02C8

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)
Maximum non-Turbo Ratio/Frequency........: 24 (2400 MHz)
Maximum Turbo Ratio/Frequency............: 32 (3200 MHz)
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (12) 23 ]
CPU C6-Cores [ 0 2 4 6 8 10 12 14 ]
CPU P-States [ (12) 16 23 ]
CPU C6-Cores [ 0 2 3 4 6 8 9 10 12 14 15 ]
CPU P-States [ (12) 16 18 23 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 14 15 ]
CPU P-States [ (12) 16 17 18 23 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 13 14 15 ]
CPU P-States [ 12 16 17 18 19 23 (24) ]
CPU P-States [ (12) 16 17 18 19 20 23 24 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 11 12 13 14 15 ]
CPU P-States [ (12) 16 17 18 19 20 22 23 24 ]
CPU P-States [ (12) 14 16 17 18 19 20 22 23 24 ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
CPU P-States [ (12) 14 16 17 18 19 20 21 22 23 24 ]
CPU P-States [ (12) 14 15 16 17 18 19 20 21 22 23 24 ]
CPU P-States [ 12 14 15 16 17 18 19 20 21 22 23 24 (32) ]

any ideas what could be wrong, anyone?

 

10.12.2.

 

Thanks

Looks like the states are showing up but I am not getting turbo speeds.

Link to comment
Share on other sites

 Share

×
×
  • Create New...