Jump to content

MSI H61M-P31/w8 for Yosemite


fbifido
 Share

4 posts in this topic

Recommended Posts

Hi,
 
I have windows 8 (120GB HD) and i need  a way to load OS X, on my system.
I am now using a vmware WS 10, running yosemite, to create my Installer USB .
I want to Install OS X 10.10 & Windows TP 10 using UEFI only.
 
My spec:
Intel HD 2500
8GB RAM
500GB HD <new>
 
I know i need:
  a) Kexts for my board
  B) a patch DSDT.aml for my board
  c) a Clover config.plist file
for my board to work properly, but for me to get most of the information from my board i need a lest a basic install of OS X.  
 
I have tried a few things but none of them seem to work with my board.
 
Step1:  <Tried> [FAILED]
I followed "midi : D's" installation guide for yosemite. http://pjalm.com/forums/index.php?topic=391.0 
I am  using vmware workstation 10 running an image of Mac OS X 10.9.5 upgraded to 10.10, to create my usb.
 
The OS X install USB was create, after setting up my UEFI, it boot without any problems.
after trying multiple different options, i am still unable to reach the Setup screen.
I am getting from kernel panic, instant reboot to system halt.
I am at step 9, on that guide, "WAIT". sometime for like 3hrs.
 
 
Step2: <Tried> [FAILED]
Try an updated clover version, like v2k_2988.
 
 
Step3:
On my MSI pc.
I press F4,F5,F6 in Clover Boot Menu to get this file 'MacStuff.zip', please see attachment.
contain:
config.plist  - this was created by me using HVT 1.7
DSDT.aml - this was mod my me, in vmware yosemite vm, using http://pjalm.com/ patches on MaciASL.
origin.zip - clover dump

MacStuff.zip

 

 

Step4: <FAILED>

I have tried and failed using a few apps on this site to create a UEFI USB of of yosemite that can boot and reach the install screen on my pc.

I reach a point of giving up, so i am going to restart again, beginning with the Easy Yosemite Installer, which was the first option i tried and failed.

 

 

Step5:

I tried to removed all "AppleIntelHD*  AppleIntelSNB* AppleIntelFramebuffer*", but Clover v2999 will not boot the 10.10 installer, it just reboot.

 

 

 

Questions:
 
1) Can someone, please check the MacStuff.zip file to see WHY i can't install or get to the installer screen(select language)?
 
2) on Step4, What do i needed to get this running?
    I will use Clover version r2988 r2999
    [HELP PLEASE]    
Edited by fbifido
Link to comment
Share on other sites

Hello

 

The only way that i found to make dual-boot with Windows+OSX was format my HDD in 2 partitions:

 

1st - OSX ------>Mac OSX reg.Cronologico

2nd - Windows --------> MS-FAT

 

And select table GUID

 

I never saw a method or used a method that enable install OSX with Windows without format HDD

 

Other this HD 2500 graphic doesn't has native support, so you need boot always with -x until try this method to enable it: http://www.insanelymac.com/forum/topic/287668-guide-intel-hd2500-full-resolution-and-qeci-1083/

This is a generic method without warranty work.

 

My advice is you a graphic card dedicated. GT 610 is cheap and works fine :)

Link to comment
Share on other sites

 


    IMPORTANT: to install Windows 7/8 in UEFI mode, the partition table must be pure GPT, it can't be hybrid MBR like used in old BIOS mode, so when you create the partitions in Disk Utilitydo NOT change the Windows partition to MS-DOS (FAT), keep all partitions as Mac OS Extended (Journaled), you will change the other partition(s) format later.

Link to comment
Share on other sites

 Share

×
×
  • Create New...