Jump to content

Asus Zenbook UX32vd - [Help] Black Screen HD 4000

Intel Zenbok i5-3317u Asus HD 4000

  • Please log in to reply
13 replies to this topic

#1
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

Guys I need your help, I only have a problem to solve, everything else works fine in my asus zenbook ux32vd with i5-3317u processor and 1366x768 resolution screen.

 

The laptop use HD4000 graphics card, it have the nvidia GT620, but it is disabled with DSDT (PINI).

 

When im going to see graphics properties I have black screen (I have uploaded two videos to explain better), and when im going to help section, or when im going to install AutoCad, when the program need evaluate the graphics the screen blinks and goes black.

The problem only happened with @LVDS, if i used @HDMI i don't have the problem, the screen never goes black, i can see in HDMI but the laptop screen stay in black.

 

The partners with the same laptop but different hardware (i7 and fullHD resolution) don't have the screen problem only have the problem the laptops with 1366x768 resolution.

 

 

Below what I tried:

  1. Various flags in config.plist of Chameleon: InjectIntel, GraphicsEnabler.InjectEDID, IgPlatformId (all). (I try with clover too, and have the same results)
  2. Ram allocated in the Bios (64,128,256,512 Mb)
  3. Changing AppleIntelFrameBufferCapri.kext
  4. Efi string.
  5. Several DSDT.

All without lasting results, sometimes the screen blinks only a few seconds, but no stay in black.

This problem occurs only with internal monitor, connecting an external monitor always works.

None of you had the same problem? I hope someone can help me.

Thank you all.

 

Attached File  MacAir 5,2 bajito93.zip   464.77KB   23 downloads



#2
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts
nobody know nothing? any one can help me? please

#3
Gintama

Gintama

    InsanelyMac Protégé

  • Members
  • Pip
  • 4 posts

change your smbios.plist to MacBookAir9,1



#4
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

change your smbios.plist to MacBookAir9,1

which? i don't find this smbios on chameleon wizard, only mac air 5,2 or mac pro 9,1/9,2

 

 

EDIT: if i used, smbios MacBook Pro 9,1, i have the same problem like MacBook Air 5,2



#5
Gintama

Gintama

    InsanelyMac Protégé

  • Members
  • Pip
  • 4 posts
My HD4000 was full acceleration for 10.9 without dsdt.
 
  1. Ram allocated in the Bios to 64Mb
  2. Change chameleon to 2265(win)
  3. Efi string.
  4. Change fakesmc to 2013-1003 https://code.google..../downloads/list
  5. Login system and install HWSensors.5.2.655
  6. Finally put all kext except 'intelcpupowermanagent' back to s/l/e and Repair permissions!

My asus:

  1. i5-3317u
  2. GT740M+HD4000

My smbios.plist :

 

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com...yList-1.0.dtd">
<plist version="1.0">
<dict>
<key>SMbiosvendor</key>
<string>AppleInc.</string>
<key>SMbiosversion</key>
<string>MBP91.88Z.00D3.B06.1205101904</string>
<key>SMboardproduct</key>
<string>Mac-6F01561E16C75D06</string>
<key>SMfamily</key>
<string>MacBookPro</string>
<key>SMmanufacturer</key>
<string>AppleInc.</string>
<key>SMproductname</key>
<string>MacBookPro9,2</string>
<key>SMserial</key>
<string>C02JP62EDTY3</string>
</dict>
</plist>

 

My org.chameleon.Boot.plist:

 

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com...yList-1.0.dtd">
<plist version="1.0">
<dict>
<key>EthernetBuiltIn</key>
<string>Yes</string>
<key>SMBIOS</key>
<string>/Extra/SMBIOS.plist</string>
<key>device-properties</key>
<string>8800000001000000010000007c0000000200000002010c00d041030a000000000101060000027fff0400100000006d006f00640065006c0000001a000000496e74656c20484420477261706869637320343030302c0000004100410050004c002c00690067002d0070006c006100740066006f0072006d002d006900640000000800000003006601</string>
</dict>
</plist>
 
I am startup with -v to find PciRoot(0x0)/Pci(0x2,0x0) at top of first page!
 
advice:
This software can help you find correct IgPlatformId:
aida64extreme320
 
 
 

 

 



#6
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

hello friend thank you for your help

 

I believe the problem is not the bootloader or smbios, i think is capri.kext, i need change the ports of LVDS, because if i don't load capri.kext i don't have the problem.

Partners with 1920x1080 screen, dont have the problem, only with low resolution 1366x768.



#7
Gintama

Gintama

    InsanelyMac Protégé

  • Members
  • Pip
  • 4 posts

AppleIntelFramebufferCapri.kext?



#8
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

AppleIntelFramebufferCapri.kext?

yes this kext if i don't load it, i don't have the problem.

 

My problem is... when i load AppleIntelFramebufferCapri.kext, the screen system @LVDS goes off



#9
Gintama

Gintama

    InsanelyMac Protégé

  • Members
  • Pip
  • 4 posts

http://iatkos.me/for...hp?f=77&t=23300



#10
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

yes i have do this, im not an hex edit expert, but when i edit with this values the system can't boot



#11
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

no ideas with this problem?



#12
pavn

pavn

    InsanelyMac Protégé

  • Members
  • PipPip
  • 86 posts

Is it on Mavericks?

 

If yes, I can send you my kexts which are needed for graphics to try.

 

 

 

Guys I need your help, I only have a problem to solve, everything else works fine in my asus zenbook ux32vd with i5-3317u processor and 1366x768 resolution screen.

 

The laptop use HD4000 graphics card, it have the nvidia GT620, but it is disabled with DSDT (PINI).

 

When im going to see graphics properties I have black screen (I have uploaded two videos to explain better), and when im going to help section, or when im going to install AutoCad, when the program need evaluate the graphics the screen blinks and goes black.

The problem only happened with @LVDS, if i used @HDMI i don't have the problem, the screen never goes black, i can see in HDMI but the laptop screen stay in black.

 

The partners with the same laptop but different hardware (i7 and fullHD resolution) don't have the screen problem only have the problem the laptops with 1366x768 resolution.

 

 

Below what I tried:

  1. Various flags in config.plist of Chameleon: InjectIntel, GraphicsEnabler.InjectEDID, IgPlatformId (all). (I try with clover too, and have the same results)
  2. Ram allocated in the Bios (64,128,256,512 Mb)
  3. Changing AppleIntelFrameBufferCapri.kext
  4. Efi string.
  5. Several DSDT.

All without lasting results, sometimes the screen blinks only a few seconds, but no stay in black.

This problem occurs only with internal monitor, connecting an external monitor always works.

None of you had the same problem? I hope someone can help me.

Thank you all.

 

attachicon.gifMacAir 5,2 bajito93.zip

 



#13
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts

okey if you can send me your kext, i don't resolved the problem :(



#14
bajito93

bajito93

    InsanelyMac Protégé

  • Members
  • PipPip
  • 65 posts
I resolved the problem with zenbook prime.
I changed my zenbook ux32vd to zenbook prime ux31a.
I think its hardware problem, when I install linux on ux32vd, the screen goes off don't wake up.
 
With ux31a no problem.
 
 
The post can be close. Thank you very much.






Also tagged with one or more of these keywords: Intel, Zenbok, i5-3317u, Asus, HD 4000


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

© 2015 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Mac Netbook  |   PHP hosting by CatN  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy