Jump to content

iPC 10.5.6 on ECS G31T-M7 v 1.0 10/100


Babiloe
 Share

10 posts in this topic

Recommended Posts

[uPDATE 20 NOV 2009]

Hi folks,

after one year.. here the update !!!!

 

OK,

I have description like this:

ECS G31T-M7 Pcb v.1

BIOS 07/31/2008

Intel Graphics GMA 3100

DDR2 800 MHz 2 GB Single

ICH7 Controller SATA iDE

HD AUDIO [iCH7 + Driver VIA VT1708B ]

Hard Disk IDE Master 40 Gb: Partition 1: XP NTFS; Partition 2: Data FAT32

Hard Disk SATA 250Gb : Partition 1 : Vista NTFS ;2: Data NTFS ; Partition 3: Partitioned at Windows ->Basic Disc not Formated

DVDRW: LG IDE Slave

Lan Card Attansic L2 onboard

Sensor: ITE 8718

PS/2 Logitech Keyboard and PS/2 IR Mouse

OSX86: IPC OSX86 10.5.6 PPF5

 

What tools to prepare ?

1. DVD ipc 10.5.6

2. Attansic L2 kext for ethernet card

3. DSDT Patcher GUI Windows Dr.Hurt 0.5 beta [you can find on the insanelymac]

4. VoodooHDA kext for audio card VIA ATA

5. PartitionWizard Home for Windows free [for manipulating existing/resizing partition]

6. Macdrive trial [for accessing the hpfs via windows inserting the dsdt.aml]

7. Latest BIOS ECS g31t-m7 1.0 10/100 or matching yours for patching the dsdt.aml [do not use the patched bios, it could kill your bios like i did before]

8. If you use ATA for DVD drive or HDD make sure it is 80 induced supporting ATA-100/133 device [or you can get still waiting / 35 error]

9. Chain0 Loader

MAKE SURE YOU INSTALL on NEW HDD or install. IF NOT MAKE SURE THAT YOU HAVE BACKUP!

Some INSTALLMENT I USED with Hackintosh with MBR scheme may broke the boot of partition 1 installed win7/vista/winxp that can't repaired with original cd boot via fixmbr/fixboot even the partition 1 has activated.

 

SO for installment in same HDD with installed windows you must separate partition:

Partition 1 [Windows] Partition 2 or 3 [Mac] Other Partition [data]

All data should be move to partition data.

The partition windows and mac should be primary.

Ghost the partition 1 with hirens boot is necessary.

 

Tool for Accidental for Partition Table Lost, Partition NTFS can not read..]

1. CD hiren's boot just for ghost [do not use or even try other tool , it can make you partition table gone, NTFS lost signature etc...]

2. Paragon Partition manager [more powerful]

3. Active Partition Recovery

 

You can use any scheme GUI or MBR...

 

The BIOS working customization set for install:

BIOS ACPI = on [can be off too]

CPU Disable Bit : OFF

CPU EIST : off [update]

CPU Halt : off [update ]

 

[Note : if you had ATA HDD you can use all set on the top on, weird huh]

 

Booting from the DVD, with boot flag => cpus=1 -v

Using Utilities -> disk Utilities -> Erase empty Partition 3 SATA 250Gb as HPFS Journaled

Customized Install Driver:

default: Vanilla kernel

GMA x3100 fix driver set checked if you use internal, if you use Nvidia VGA add on pick Nvidia darwin

ICHx SATA driver checked [do not use PIIXATA !!, it will give you error 35]

PS/2 keyboard and/or mouse fix checked [if you use ps/2]

NTFS-3G MacFuse checked [or you can use Paragon NTFS more powerful]

DSDT newHPET checked [update : for fixing the error in System Preferences]

SMBIOS 27 DDR2 800 Mhz or SMBIOS 28 [update : for fixing error in the System Preferences (Configure as your DRAM speed)] or other just for cosmetics

Kexthelper, EfiStudio, OSX86tool should be installed also.

Ethernet and Audio kext updated after installation...

Success install

 

Post installation alternate 1 if you can goto windows..

1. Goto Bios

The BIOS working customization set for install:

BIOS ACPI = on

CPU Disable Bit : on

CPU EIST : on

CPU Halt : off

2. Goto Windows

3. Install Mac drive

4. Put Dsdt.aml in root of your HPFS mac

5. Boot...

 

Alternate 2

1. with all cpu and acpi off goto mac

2. boot quite long...

3. copy dsdt.aml from your usb / windows partition to hpfs root partition.

reboot..

 

HOW TO PATCH DSDT ?

1. Download the Bios

2. Download the DSDT Patcher Bios 0.5beta

3. Mute and Local0 Fix on, default fix on [3 checked like HPET, and other two.]

4. For vga add on, make sure pci 1 , PEG on, put nvidia or ati as you new add on.

5. Pick first tab to create Bios with AML checked..

6. then you have the DSDT.AML

 

INSTALL Ethernet and HD Audio output

install kext voodoohda.kext and EthernetL2.kext by drag into kexthelper. add the password, click easy install, reboot

091015S10100_G31T_M7.zip

kext.zip

Link to comment
Share on other sites

  • 8 months later...
  • 3 weeks later...
hi, i'am installing mac osx86 in 5 computer with motherboard G31T-M7, but without success.

 

i need your link http://www.4shared.com/file/85191029/e53dbaf0/dsdt.html but is disable

 

only one computer is success but the time but is approximately 5 minutes ;)

 

 

can you help?

 

DEAR sonia...

It has updated today..

Where you stuck in?

The long boot it was caused by DSDT on VGA.

I think you must buy the cheapest VGA Nvidia like 7300SE and use my nVidia DSDT.aml

Link to comment
Share on other sites

  • 4 months later...
Already detected as double CORE!!!!

Finally,,,Working

 

 

hi, I'am installing mac osx86 on my computer with motherboard G31T-M7, it was success, with the BIOS 07/31/2008. But I have a problem... when I turn off the computer I need to reset the bios again... so I think I coudn't manage the part in wich I need to patch the dsdt file... and after that Can I restore the bios with the latest bios update?...

 

Please... can you help me with this step by step, I'll really appriciate that.

Link to comment
Share on other sites

  • 4 weeks later...
hi, I'am installing mac osx86 on my computer with motherboard G31T-M7, it was success, with the BIOS 07/31/2008. But I have a problem... when I turn off the computer I need to reset the bios again... so I think I coudn't manage the part in wich I need to patch the dsdt file... and after that Can I restore the bios with the latest bios update?...

 

Please... can you help me with this step by step, I'll really appriciate that.

There's 2 option:

1. Try use RPCPatch kext

http://www.kexts.com/view/151-cmos_reset_fix_(via_kext).html

or

2. patch the dsdt especially on RPC Bios using DSDT patcher http://www.osx86.es/

 

My DSDT based od 10.5.6 kernel that doesnt erase the bios.

I will update the installation based on Snow Leopard 10.6.2 that run out of the box!

Link to comment
Share on other sites

  • 4 months later...

Hi this is my first post here.... could you give me help with my ecs g31t-m7 v1 i cant get it to work in any way. I tried installing Ideneb 1.4, I deneb 1.3 and ipc 10.5.6 but luckily no success at all. Im using inno3d 7200gs video. could you give me the step by step and bios and dsdt needed for this? Any help would be much appreciated.

 

Thanks

 

zoyti

Link to comment
Share on other sites

Hi this is my first post here.... could you give me help with my ecs g31t-m7 v1 i cant get it to work in any way. I tried installing Ideneb 1.4, I deneb 1.3 and ipc 10.5.6 but luckily no success at all. Im using inno3d 7200gs video. could you give me the step by step and bios and dsdt needed for this? Any help would be much appreciated.

 

Thanks

 

zoyti

 

 

Well I have ditches 10.5.x a long time ago. I have been in 10.6.2 now anyway, it has problem free, and can run without DSDT!

 

I recommended that you buy usb keyboard, 4GB usb flashdisk, and stay away from radeon vgacard, and i can see you already had nvidia. i use apple 10.6.0 DVD iso with myhack installer.

 

 

Please upgrade.

 

The tutorial to upgrade, i already posted in indonesians

 

http://mac-inul.com/viewtopic.php?p=12697

 

You can use google languange tools to translate it.

 

Regards from indonesia.

Link to comment
Share on other sites

Well I have ditches 10.5.x a long time ago. I have been in 10.6.2 now anyway, it has problem free, and can run without DSDT!

 

I recommended that you buy usb keyboard, 4GB usb flashdisk, and stay away from radeon vgacard, and i can see you already had nvidia. i use apple 10.6.0 DVD iso with myhack installer.

 

 

Please upgrade.

 

The tutorial to upgrade, i already posted in indonesians

 

http://mac-inul.com/viewtopic.php?p=12697

 

You can use google languange tools to translate it.

 

Regards from indonesia.

 

Thanks for the reply..

 

Will my ecs g31t-m7 will run in SL with inno3d 9500GT? without any bios patches? I downloaded iatkos 10.6.3 and still no luck booting up to SL with ecs g31t and inno 3d 9500GT.

Link to comment
Share on other sites

 Share

×
×
  • Create New...