slipttees Posted December 15, 2008 Share Posted December 15, 2008 Update 02-08-2011 -> Onboard GMA X3500 doesn't work 1. Update your Bios Bios #0118 PS: recommendable bios update method: Use Self-extracting Windows*-based update file includes Software License Agreement and the utility for updating the BIOS. It is designed to be used on Windows* systems. This method is the most commonly used. 2. Bios Setting: Main: Advanced: Peripheral Configuration: Audio: Enable High Definition Front Panel Audio: Enable On-Board LAN: Enable Onboard 1394: Enable Drive Configuration: ATA/IDE Mode: Native Configure SATA as: AHCI Smart: Enable Hard Disk Pre-Delay: No Floppy Configuration: Diskette Controller: Disable Chipset Configuration: PCI Latency Timer: 32 HPET: Enable USB Configuration: Usb Ports: Enable Usb Legacy: Enable Security: XD: Enable VT: Enable Power: EIST: Enable ACPI: S3 State 3. Installation: 3.1 Burn DG35EC BootCD, 3.2 Install Mac OS X 10.6.3 DVD. 3.3 Install 10.6.8 Combo Update 4. Pos Install: 4.1 Install DG35EC Pos Install.pkg 4.2 Instal DG35EC Drivers.pkg 5. Install Chameleon: 5.1. Install Chameleon RC5 PS: com.apple.Boot.plist rename to org.chameleon.Boot.plist 6. DSDT: 6.1 If u do not install dsdt with "DG35EC Pos-Install.pkg" use DSDTAuto Patcher and run and copy "DSDT.aml" that was created in your Desktop and put it on Extra. Thanks MaLd0n Done Link to comment Share on other sites More sharing options...
Corben2005 Posted December 22, 2008 Share Posted December 22, 2008 Hello, thanks for the guide, but I have a problem with booting from the Retail Leopard DVD. PC: - Intel Board DG35EC (on board graphic and the newest BIOS) - E7300@2,66 GHz - 2GB RAM - SATA Port 0 is a WD 80GB - SATA Port 1 a a DVD ROM If I go through this guide, step by step, I get this report: ( all BIOS settings like you, with AHCI) http://img88.imageshack.us/my.php?image=os...32loadertx5.jpg look there: http://forum.insanelymac.com/index.php?s=&...t&p=1009129 pleas help Link to comment Share on other sites More sharing options...
LatinMcG Posted December 27, 2008 Share Posted December 27, 2008 i cant get the boot132 to work says invalid checksum .. i have ide samsung dvd drive. cant use ahci ?. it freezes on intel post screen. i have to pull hd sata of and power on then change to ide mode save exit (duh) and plug hd back in so it boots anything should i change to a sata dvd and see if it works ? DG35EC bios updated tsst /samsung ide drive 4 gb ram 2x 2gb evga 8600gt 256mb wd 500gb partitioned xp primary, osx primary working with kalyway 10.5.2 with ppf jmicron patch not in ahci mode. combo update to .5.3 then dloaded .5.4 then efi v9 then pre and post patch combo updated to .5.5 i cant get protools 8 to finish install at end last minute crashes. hablo español also (<gwb dodging) Link to comment Share on other sites More sharing options...
Corben2005 Posted December 27, 2008 Share Posted December 27, 2008 you can ahci only use with s-ata and to use the 132 cd you need to use ahci. Link to comment Share on other sites More sharing options...
LatinMcG Posted December 27, 2008 Share Posted December 27, 2008 Thanks Corben2005 going to store to get sata dvd and retry. i got retail dvd ill post back in a day or so results...pc is at friends house Link to comment Share on other sites More sharing options...
pkdill Posted January 1, 2009 Share Posted January 1, 2009 Hi, I also got a problem like this (like the problem which Corben2005 said before) : I had set all BIOS settings as like as slipttees posted... I tested it with both IDE and ACHI mode, One thing I found is my PC use the on board display but slipttees use Nvidia GeForce 8400 GS (http://www.hackint0sh.org/forum/showpost.php?p=339021&postcount=1), so there is a difference. Does anyone have any idea for this ?? [~~ Sorry for my poor English] Link to comment Share on other sites More sharing options...
Corben2005 Posted January 1, 2009 Share Posted January 1, 2009 It does not work with On-board graphic. I have tried a lot of different things, but nothing works then I build in my 8800GTX from my Win PC and look there it works. See my Post in the DFE's BOOT-132 Thread: (sorry I forgot to write it here) http://forum.insanelymac.com/index.php?s=&...t&p=1009129 Link to comment Share on other sites More sharing options...
pkdill Posted January 2, 2009 Share Posted January 2, 2009 a lot...but I have no external graphic card now. Do you think it will work if I add a fixed AppleIntelGMAX3100.kext into initrd.img...??? Link to comment Share on other sites More sharing options...
Corben2005 Posted January 2, 2009 Share Posted January 2, 2009 I have never read that it will work with "a fixed AppleIntelGMAX3100.kext", but you can try it. If it work it would be very nice for my, because now I need my card from my other Pc and if I want to run Mac OS X I can not run my WinPC Link to comment Share on other sites More sharing options...
slipttees Posted January 3, 2009 Author Share Posted January 3, 2009 everyone check bios settings after install osx, and try again! thx! Link to comment Share on other sites More sharing options...
pkdill Posted January 3, 2009 Share Posted January 3, 2009 Thanks !!! But I can't check the bios settings after install osx. It is because I still can't boot into the install DVD although I set the BIOS setting like yours. I read Corben2005's case, he could boot the DVD and install the retail Mac OS X after adding an external graphic card. So I think my case may be the on board graphic problem and I still finding the solution for this... Do you have any idea about installing Mac OS X with the on board graphic ??? Thanks !!! Link to comment Share on other sites More sharing options...
jazzman746 Posted January 3, 2009 Share Posted January 3, 2009 Well now i have this: Installed with XXX X86 10.5.6 Voodoo Kernel 5.0 Audio, working with azalia but no microphone input Video, work OK with nviject 0.2.1 512mb, but when change resolution i get blank screen that fixes sleeping Network, working OK with INTEL82566MM Kext, but fails when sleep Shut down OK Thats it. So any help with my issues very appreciated Mobo INTEL DG35EC CPU Intel core 2 duo 3Ghz RAM Corsair DDR2 2Gb 800 Mhz X2 Maxtor HDD 500Gb SATA EVGA Gforce 9500gt Link to comment Share on other sites More sharing options...
MacNutty Posted January 4, 2009 Share Posted January 4, 2009 How did you get your audio working? Please share the kext(s) if possible. I to have the similar audio setup. Link to comment Share on other sites More sharing options...
slipttees Posted January 7, 2009 Author Share Posted January 7, 2009 first post updated Link to comment Share on other sites More sharing options...
BigDyno Posted January 8, 2009 Share Posted January 8, 2009 Great Post! I was looking into this board to purchase for my next machine. I'm currently using an AMD machine and running Leopard flawlessly. But I'm stuck at 10.5.2 because I use this machine as my primary and don't want to screw it up by updating. That's why I'm looking to buy a new machine. Does this board allow you to use Apple Updater to keep current? I've heard problems with the ethernet not working after sleep. And problems with the sound? How does it perform, and anything that doesn't work/don't like about the install? Thanks in advance! Link to comment Share on other sites More sharing options...
EnXarXa Posted January 9, 2009 Share Posted January 9, 2009 I have the same problem with this MB DG35EC (like the problem of Corben2005 & pkdill) ... the MB video not work and then installation crash before the OSx installer run after the verbose mode shows the "normal" messages ... I prove to inject the new(s)(?) drivers for de Intel graphics AppleIntelGMAX3100.kext & AppleIntelGMAX3100FB.kext (of the first post updated by slipttees) to the kext.img of the original boot132 of slipttees ... and not work. any idea? O.K. with an external NVIDIA graphics card works fine ... Link to comment Share on other sites More sharing options...
slipttees Posted January 9, 2009 Author Share Posted January 9, 2009 X3500 haven't support, search patch about it! PS: i'm use Nvidia Card Link to comment Share on other sites More sharing options...
EnXarXa Posted January 9, 2009 Share Posted January 9, 2009 O.K. Leopard is in the PC Box. But NOT Audio & NOT Network ... and the PS2 Mouse & Keyboard not work, only USB. Link to comment Share on other sites More sharing options...
slipttees Posted January 9, 2009 Author Share Posted January 9, 2009 no Audio ? AppleAzalia.kext Driver and remove AppleHDA.kext, No Ethernet ? use Intel82566MM.kext, PS2 Use NubPS2Controller. thx O.K. Leopard is in the PC Box. But NOT Audio & NOT Network ... and the PS2 Mouse & Keyboard not work, only USB. Link to comment Share on other sites More sharing options...
EnXarXa Posted January 10, 2009 Share Posted January 10, 2009 Work in progress ... Audio works fine with AppleAzalia and removing appleHDA,kext ... but mods are needed in the Info.plist of the kext by dependency problems with Libraries. In Intel82566MM & ACPIPS2Nub kext exist this problem, too. I mod the vendor in Intel82566MM too ... I see the error with the kextload -v 6 name_of_kext (after a sudo -s in terminal mode) ... check the inconsistency load of versions of the libraries comparing with the result of the kextstat. Mod the Info.plist and reload then kext. Finally PS2 works, Audio works (without input) & network (Ether) works 10/100/1000 ... next is the integrated graphics, grrrrrrr .... Link to comment Share on other sites More sharing options...
slipttees Posted January 10, 2009 Author Share Posted January 10, 2009 I'll try TheStevoKext about GMA X3500...waiting news! thx Link to comment Share on other sites More sharing options...
blackfish Posted February 2, 2009 Share Posted February 2, 2009 Thanks to you, I have a working system: DG35EC Mobo 8 gigs RAM Nvidia 8400GS (nvinject.kext with KextHelper) Belkin F5D8050 USB Wifi (Belkin kext installed with KextHelper) Logitec Wireless USB Mouse Apple USB keyboard Chameleon boot on 500GB sata drive Leopard 10.5.4 I am wondering if anything will break if I run Software Update to get up to 10.5.6? If so, is there a good process to follow to prep the machine for this? Thanks again, Blackfish Link to comment Share on other sites More sharing options...
flock44 Posted February 5, 2009 Share Posted February 5, 2009 Hi Sliptees, This is my second request. I ve posted my first request on Hackintosh.org on the same topic. Please respond me.... Below link explains the issue i m facing in detail... I ve posted screenshots of issue n screenshots of BIOS. http://www.insanelymac.com/forum/index.php...9096&st=260 *** (Read the post by flock44) I ve almost same config of your's mobo: Intel DG35EC Processor: Intel Core 2 Duo 2.53 Ghz Ram: 2 GB HD Drive: Seagate 400 Gb (SATA) Connected to Sata port (0) DVD Drive: LG RW 22x (SATA) connected to Sata port (1). Thnx in Advance.... Update 1/7/2009 Intel Board DG35EC Guide First, we need to prepare the ground. Get and update with last Bios there Get DG35EC made me :-) there OSX86Tools 1.0 Final: there Thx Jedi PCWiz Chameleon 1.0.11 Installer: there Thx All Chameleon's Bios Setting: Main: Advanced: Peripheral Configuration: Audio: Enable High Definition Front Panel Audio: Enable On-Board LAN: Enable Onboard 1394: Enable Drive Configuration: ATA/IDE Mode: Native Configure SATA as: AHCI Smart: Enable Hard Disk Pre-Delay: No Floppy Configuration: Diskette Controller: Disable Chipset Configuration: PCI Latency Timer: 32 HPET: Enable USB Configuration: Usb Ports: Enable Usb Legacy: Enable Security: XD: Enable VT: Enable Power: EIST: Enable ACPI: S3 State Boot: Boot Configuration: Advanced Boot to removable device: Disable Boot to Network: Disable Usb Boot: Disable Boot usb Device first: Disable Usb Mass Storage Emulation Type: Auto PS: Use HDD in the SATA0 Port and DVD in the SATA 1 Port Start cd boot-132... In darwin screen type Enter, Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe] Replace the boot cd-132 at the retail dvd! Waiting 10 sec and press Enter, type f8 and type -v Open Disktutil Create GUID Partition table and Install Mac OS X Reboot System, Start cd boot-132 again... In darwin screen type Enter, Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe] type 80 and press Enter, type -v and Enter Open boot-132 and mount kexts.img in the kexts.img folder copy: Intel82566MM.kext, IntelCPUPMDisabler.kext, SMBIOSEnabler.kext, AppleDecrypt.kext to /System/Library/Extensions/ PS: ACPIPS2Nub.kext ApplePS2Controller.kext if you use keyboard and mouse PS2 :-) after replacing the extensions open the terminal and use: sudo -s chmod -R 755 /System/Library/Extensions/* chown -R 755 /System/Library/Extensions/* diskutil repairPermissions / touch /System/Library/Extensions/* exit sudo -k exit Open OSX86Tools or chameleon installer and install "Chameleon EFI" in OS X Volume! I tried Chameleon installer three times to work ! Reboot and Work Full speed Retail Now, 5 sec startup and 3sec halt Drivers update: Intel 82566DC Ethernet Controller - There Intel X3500 VGA Driver (Not Test There!) - There ALC888S = I'm use Azalia Driver, work only two channel ! Thanks f41qu3, a1kon, HotBreeze, and everyone Thanks. Big Thx onemanstrash :-p Sorry my pour English! Link to comment Share on other sites More sharing options...
slipttees Posted February 6, 2009 Author Share Posted February 6, 2009 yo bro, u can try my boot-132.iso in first post. Look, Retail Don't Work with MBR Partition Table, only GUID okay ? and dual boot system u neede a bouth HDD and select in bios system in F10 u HDD boot. good luck! sorry pour english Hi Sliptees, This is my second request. I ve posted my first request on Hackintosh.org on the same topic. Please respond me.... Below link explains the issue i m facing in detail... I ve posted screenshots of issue n screenshots of BIOS. http://www.insanelymac.com/forum/index.php...9096&st=260 *** (Read the post by flock44) I ve almost same config of your's mobo: Intel DG35EC Processor: Intel Core 2 Duo 2.53 Ghz Ram: 2 GB HD Drive: Seagate 400 Gb (SATA) Connected to Sata port (0) DVD Drive: LG RW 22x (SATA) connected to Sata port (1). Thnx in Advance.... Link to comment Share on other sites More sharing options...
flock44 Posted February 6, 2009 Share Posted February 6, 2009 Hey Slipttees, First of thnx a lot for the reply... So all i need to do is use ur boot 132.iso (which ive downloaded from ur first post)? I'll try to use it to boot. I just some how want to get to installation screen. i'll also make sure to change my BIOS settings to those u have mentioned in ur first post. But can u pls explain me why was this happening? i mean never endin Boot to Hexadecimal Value loop without showin up Retail DVD or Installation screen? Sorry but just curious to know so that if someone faces the same problem wanned to help them too.... You know it was hell of a experience when i didnt get any help. Hope you understand... And will post the result's this weekend after using the Boot 132 u made for DG35EC... Cheers! yo bro, u can try my boot-132.iso in first post. Look, Retail Don't Work with MBR Partition Table, only GUID okay ? and dual boot system u neede a bouth HDD and select in bios system in F10 u HDD boot. good luck! sorry pour english Link to comment Share on other sites More sharing options...
Recommended Posts