Hi Kaly,
The Kalyway 10.5.1 Install DVD is well done,
THANK YOU SO MUCH!I had to insist on installing and finally I succeeded.
1 Notebook Dell 6400/E1505 - GeekBench score ~1900 , XBench score ~110
- Leopard Kalyway 10.5.1 with
"vanilla" kernel working fine - CPU T7200 Intel Core 2 Duo at 2 GHz
(installation and working fine with only one core BIOS enabled) - 2x1 Gb DDR2 PC5300 (667 MHz) -
working fine - GMA 945Mobile (GMA950 graphic card) -
QE and CI working fine under different resolutions (no patching needed, active directly in the system installation)
- HDD Toshiba 120 GHz (with the map as follows first/primary partition WinVista 32 NTFS 512 bit/sector, second/primary partition Leopard 10.5.1 EFI-MBR HFS+ Extended Journaled, other three extended/logical partitions NTFS 512 bit/sector)
- DVD-RW Philips -
working fine - Firewire 400
working fine under OSX (perfect connection to an iMac 17")
-
Sound Sigmatel 9200 patched with Taruga's 1.20 patch and linux codec dump
http://psykopat.free.fr/apple/AppleHDA/sig...igmatel9200.txt -
working fine as normal output (louder up and quiet down buttons working only),
BUT NO MIC - 3 in 1 card reader
working fine - all
USB active with very good speed
-
NO LID REACTIVATION AFTER CLOSING -
Intel Wireless 3945a/b/g NOT WORKING (the PCI-e minicard can be replaced with Dell ones 1390 or even 1500 Draft N - for only max. 50$)
2 PC System - build up from components GeekBench score ~3100, XBench score ~160
- Leopard Kalyway 10.5.1
working with patched kernel ("vanilla" gives short restart before loading) - ASUS P5LD2 motherboard (BIOS updated to 1903), chipset Intel 945P
- CPU E6300 Intel Core 2 Duo 1.86 GHz (overclocked to 2.33 GHz) -
working fine with both cores active - 4x1 GB DDR2 PC5300 (667 MHz) - no overclocking - working with 3.2 GB for System and BIOS at POST reports the rest of 800MB "Appropriated" - motherboard limited capability
- Sapphire ATI X1300Pro 256 MB,
working with DiaboliK patch (error on installation but after restarting the system everything works fine with QE and CI and different resolutions and frequencies),
VGA working fine BUT NO DVI - monitor ASUS MB19TU at 1280x1024x32@75
on VGA - Western Digital 250 GB Sata2,
EFI-GUID partitioned from Kalyway DVD, reserved only for OSX, system installed on second/primary partition (except first/primary EFI partition, the rest of them have a 128 MB unallocated space appeared after partitioning in OSX with diskutil
DO NOT MESS WITH THEM - Seagate Quantum 160 GB Sata2,
MBR partitioned reserved only for WinVista32, system installed on first/primary NTFS partition, second/primary NTFS partition and the rest of three NTFS extended/logigal partitions (all of them writable fromLeo with MacFuse and NTFS-3G driver)
- Western Digital 40 GB IDE 100,
EFI-GUID partitioned from Kalyway DVD, reserved for Leo's TimeMachine
- DVD-RW ASUS 1608S,
working just fine - LAN on-board
working fine without patching -
sound ALC882 on-board working with Taruga's 1.20 patch and the linux codec dump
http://psykopat.free.fr/apple/AppleHDA/realtek/882.txt -
working fine even the front connectors for out and mic (not tested the SPDIF output)
- all
USB active with very good speed
I will give it a try to format the WD250 as EFI-MBR for Leo to see if "vanilla" kernel will work.