Trying to find the fastest system out there,,,,with QE/CI (ala FCP and Logic Use (very FPU and CPU dependent) thus the QE/CI enabled users only...


Anyone get CPU over 100% not total score but CPU RESULTS over 100%?

If so, if not in sig, please elaborate on system setup.

Cinebench 350+??

I'll go first with my stock, then tomorrow, post the new setup (Asus maybe, with 20% increase, although I still think a overclocked D 930 at 3.6 yields a 18% increase only in FPU/CPU...

CINEBENCH 9.5
****************************************************

Tester : 1

Processor : D930 Stock
MHz : 3.0
Number of CPUs : 2
Operating System : 10.4.6

Graphics Card : GMA950
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 237 CB-CPU
Rendering (Multiple CPU): 415 CB-CPU

Multiprocessor Speedup: 1.75

Shading (CINEMA 4D) : 312 CB-GFX
Shading (OpenGL Software Lighting) : 1120 CB-GFX
Shading (OpenGL Hardware Lighting) : 544 CB-GFX

OpenGL Speedup: 3.59

****************************************************

CPU Test ONLY 63.02
GCD Loop 87.66 4.62 Mops/sec
Floating Point Basic 71.61 1.70 Gflop/sec
vecLib FFT 45.38 1.50 Gflop/sec
Floating Point Library 62.27 10.84 Mops/sec



Results 94.67 WITH THREAD AND MEMORY
System Info
Xbench Version 1.2
System Version 10.4.6 (8I1119)
Physical RAM 2048 MB
Model ADP2,1
Drive Type ST3300631A
CPU Test 63.68 (CPU OF COURSE STILL AT 63.6)
GCD Loop 91.21 4.81 Mops/sec
Floating Point Basic 71.10 1.69 Gflop/sec
vecLib FFT 45.50 1.50 Gflop/sec
Floating Point Library 63.25 11.01 Mops/sec
Thread Test 153.81
Computation 137.33 2.78 Mops/sec, 4 threads
Lock Contention 174.77 7.52 Mlocks/sec, 4 threads
Memory Test 105.45
System 95.93
Allocate 65.51 240.57 Kalloc/sec
Fill 129.40 6291.57 MB/sec
Copy 120.79 2494.91 MB/sec
Stream 117.07
Copy 112.38 2321.18 MB/sec
Scale 116.15 2399.70 MB/sec
Add 120.64 2569.84 MB/sec
Triad 119.46 2555.49 MB/sec


53.26 Xbench Pass 1 ATA 100 Full Score 60 hz LCD
67.94 Xbench Pass 2 ATA 100 " "60 hz LCD
59.38 Dbeam/2d disabled/enabled ATA 100 Pass 1 60 hz LCD
65.76 Dbeam/2d disabled/enabled ATA 100 Pass 2 60 hz LCD

73.16 Dbeam/2d disabled/enabled ATA 100 Pass 1 75hz Display LCD
72.81 Dbeam/2d disabled/enabled ATA 100 Pass 2 75hz LCD

Note the increased score with higher resolution setting of 75hz vs 60 hz.???

man. you must delete your post.
you have only 94.
Xbench don't give objective appraisal.

my CPU test (pentium D805 - stock 2.66Ghz)
CPU Test 60.55
GCD Loop 81.42 4.29 Mops/sec
Floating Point Basic 68.52 1.63 Gflop/sec
vecLib FFT 45.50 1.50 Gflop/sec
Floating Point Library 58.12 10.12 Mops/sec


i don't trust what it's so near with yours D930 !!
and in total my config have over 90-91 points
with a half of your ram (1 GB) and with the slowest CPU.


also i have AMD 64 3200+ (Winchester core SSE2 ONLY !!!)
CPU Test 65.97
GCD Loop 103.50 5.46 Mops/sec
Floating Point Basic 82.95 1.97 Gflop/sec
vecLib FFT 40.76 1.34 Gflop/sec
Floating Point Library 69.56 12.11 Mops/sec
it's beat yours D930. hmmmmmmmm... maybe maybe.. but not sure...

Here are my results.

Cinebench:

CINEBENCH 9.5
****************************************************

Tester : Tester

Processor : Pentium D 920
MHz : 2800
Number of CPUs : 2
Operating System : 10.4.6

Graphics Card : D945PSN
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 237 CB-CPU
Rendering (Multiple CPU): 441 CB-CPU

Multiprocessor Speedup: 1.86

Shading (CINEMA 4D) : 310 CB-GFX
Shading (OpenGL Software Lighting) : 1244 CB-GFX
Shading (OpenGL Hardware Lighting) : 2550 CB-GFX

OpenGL Speedup: 8.22

****************************************************

Xbench:

Results 110.99
System Info
Xbench Version 1.2
System Version 10.4.6 (8I1119)
Physical RAM 2048 MB
Model ADP2,1
Drive Type Maxtor 6V300F0
CPU Test 61.75
GCD Loop 85.27 4.49 Mops/sec
Floating Point Basic 72.02 1.71 Gflop/sec
vecLib FFT 44.30 1.46 Gflop/sec
Floating Point Library 60.29 10.50 Mops/sec
Thread Test 158.05
Computation 142.90 2.89 Mops/sec, 4 threads
Lock Contention 176.80 7.61 Mlocks/sec, 4 threads
Memory Test 111.55
System 92.24
Allocate 60.29 221.39 Kalloc/sec
Fill 126.03 6127.86 MB/sec
Copy 124.97 2581.14 MB/sec
Stream 141.09
Copy 135.30 2794.51 MB/sec
Scale 135.31 2795.45 MB/sec
Add 147.94 3151.49 MB/sec
Triad 146.84 3141.16 MB/sec
Quartz Graphics Test 107.27
Line 108.01 7.19 Klines/sec [50% alpha]
Rectangle 103.73 30.97 Krects/sec [50% alpha]
Circle 104.03 8.48 Kcircles/sec [50% alpha]
Bezier 100.84 2.54 Kbeziers/sec [50% alpha]
Text 122.24 7.65 Kchars/sec
OpenGL Graphics Test 118.60
Spinning Squares 118.60 150.45 frames/sec
User Interface Test 198.00
Elements 198.00 908.70 refresh/sec
Disk Test 113.89
Sequential 129.16
Uncached Write 139.16 85.44 MB/sec [4K blocks]
Uncached Write 137.42 77.75 MB/sec [256K blocks]
Uncached Read 107.38 31.42 MB/sec [4K blocks]
Uncached Read 139.04 69.88 MB/sec [256K blocks]
Random 101.84
Uncached Write 77.49 8.20 MB/sec [4K blocks]
Uncached Write 122.67 39.27 MB/sec [256K blocks]
Uncached Read 95.63 0.68 MB/sec [4K blocks]
Uncached Read 128.80 23.90 MB/sec [256K blocks]

Not over 100 on cpu only but close.

CineBench here CINEBENCH 9.5
****************************************************

Tester :

Processor : AMD64
MHz : 2700
Number of CPUs : 1
Operating System : Mac OS 10.4.6

Graphics Card :
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 392 CB-CPU
Rendering (Multiple CPU): --- CB-CPU


Shading (CINEMA 4D) : 435 CB-GFX
Shading (OpenGL Software Lighting) : 1784 CB-GFX
Shading (OpenGL Hardware Lighting) : 3026 CB-GFX

OpenGL Speedup: 6.95

****************************************************

Xbench

Not running Disk Tests cause im using an old 40GB disk not my Sata one.
8 more to 100 cpu result

Results 131.81
System Info
Xbench Version 1.2
System Version 10.4.6 (8I1119)
Physical RAM 1024 MB
Model ADP2,1
Drive Type ST340016A
CPU Test 91.98
GCD Loop 148.99 7.85 Mops/sec
Floating Point Basic 112.62 2.68 Gflop/sec
vecLib FFT 55.97 1.85 Gflop/sec
Floating Point Library 99.73 17.37 Mops/sec
Thread Test 94.58
Computation 67.68 1.37 Mops/sec, 4 threads
Lock Contention 156.97 6.75 Mlocks/sec, 4 threads
Memory Test 134.02
System 142.95
Allocate 200.48 736.22 Kalloc/sec
Fill 136.84 6653.60 MB/sec
Copy 115.06 2376.55 MB/sec
Stream 126.14
Copy 119.10 2460.00 MB/sec
Scale 119.51 2468.96 MB/sec
Add 133.06 2834.55 MB/sec
Triad 134.55 2878.40 MB/sec
Quartz Graphics Test 171.83
Line 123.54 8.23 Klines/sec [50% alpha]
Rectangle 166.06 49.58 Krects/sec [50% alpha]
Circle 155.66 12.69 Kcircles/sec [50% alpha]
Bezier 142.51 3.59 Kbeziers/sec [50% alpha]
Text 649.08 40.60 Kchars/sec
OpenGL Graphics Test 159.58
Spinning Squares 159.58 202.44 frames/sec
User Interface Test 220.92
Elements 220.92 1.01 Krefresh/sec

Oh poopy doop. I should have been more specific, are you AMDers (I also have a AMD64 SSE2 only) using a ATIX1600?

In a nutshell, want to see RENDERING over 350 with QE/CI enabled.....AMD is fine, just want to know if those are working QE/CI.

Nice marks so far. If we can get into the 350 render mark, we getting close to quad G5, but not for 4 way render, but for one/two cpu render.

2nd thing is Xbench CPU score, sure the Xbench can be unreliable, but notice that the CPU mark (no memory, thread test) remains stable regardless. Thus looking for OVER 100 in CPU score in Xbenchy!

Peace

Im using a ATI X1600 Pro 256MB DDR2, forgot to mention it above. About the render my score was 392, not bad for a 100€ A64 3200+ (overclocked of course).

Something odd with your setup, Retroz. My 830 shouldn't be faster I don't think:

Cinebench

XBench CPU

Gets 112 or 121 (forget which) on full xbench.

I also have a 2.66 GHz P4 processor, and I am curious why some of my numbers are much slower than the OP. Is it simply because of the 2GB of ram vs 1GB?
System Info
Xbench Version 1.2
System Version 10.4.7 (8J2135)
Physical RAM 1024 MB
Model ADP2,1
Drive Type HDT722516DLAT80
CPU Test 50.06
GCD Loop 96.91 5.11 Mops/sec
Floating Point Basic 56.84 1.35 Gflop/sec
vecLib FFT 27.71 914.11 Mflop/sec
Floating Point Library 62.91 10.95 Mops/sec
Thread Test 83.32
Computation 87.13 1.77 Mops/sec, 4 threads
Lock Contention 79.82 3.43 Mlocks/sec, 4 threads
Memory Test 78.38
System 64.85
Allocate 47.37 173.96 Kalloc/sec
Fill 84.13 4090.45 MB/sec
Copy 75.38 1556.99 MB/sec
Stream 99.05
Copy 93.91 1939.65 MB/sec
Scale 93.01 1921.57 MB/sec
Add 105.60 2249.51 MB/sec
Triad 105.13 2248.98 MB/sec

Here's mine. Core 2 Duo E6600 with DDR2-667 ram. Specs in my .sig.

Cinebench 9.5
Rendering (Multiple CPU): 730 CB-CPU
Shading (CINEMA 4D) : 487 CB-GFX
Shading (OpenGL Hardware Lighting) : 2523 CB-GFX

Xbench
CPU Test 119.55
GCD Loop 282.55 14.89 Mops/sec
Floating Point Basic 137.01 3.26 Gflop/sec
vecLib FFT 87.74 2.89 Gflop/sec
Floating Point Library 89.10 15.52 Mops/sec
Thread Test 240.63
Computation 220.21 4.46 Mops/sec, 4 threads
Lock Contention 265.22 11.41 Mlocks/sec, 4 threads
Memory Test 138.44
System 151.37
Allocate 122.98 451.61 Kalloc/sec
Fill 162.37 7894.79 MB/sec
Copy 180.88 3735.99 MB/sec
Stream 127.54
Copy 119.82 2474.88 MB/sec
Scale 124.21 2566.16 MB/sec
Add 134.43 2863.62 MB/sec
Triad 132.85 2842.07 MB/sec

Other benchmarks
Xbench: 152.19
Geekbench:234.1
Photoshop Bench Smart Blur:105.1
Power Fractal:8791.4

mir...

@miramar: Realtek 8111 GB PCIe works with R1000 driver on same mobo ...

CINEBENCH 9.5
****************************************************

Tester : Atmosfear

Processor : Core 2 Duo E6600
MHz : 2400
Number of CPUs : 2
Operating System : MacOS X 10.4.8

Graphics Card : X1900 XT 256MB
Resolution : 1920x1200
Color Depth : 32bpp

****************************************************

Rendering (Single CPU): 394 CB-CPU
Rendering (Multiple CPU): 739 CB-CPU

Multiprocessor Speedup: 1.87

Shading (CINEMA 4D) : 479 CB-GFX
Shading (OpenGL Software Lighting) : 1851 CB-GFX
Shading (OpenGL Hardware Lighting) : 3936 CB-GFX

OpenGL Speedup: 8.22

****************************************************

XBench (no Disk - w/Disk 152 pts)
Results 187.10
System Info
Xbench Version 1.2
System Version 10.4.8 (8L2127)
Physical RAM 4096 MB
Model ADP2,1
Drive Type Maxtor 6Y200M0
CPU Test 124.83
GCD Loop 285.20 15.03 Mops/sec
Floating Point Basic 136.76 3.25 Gflop/sec
vecLib FFT 99.60 3.29 Gflop/sec
Floating Point Library 89.41 15.57 Mops/sec
Thread Test 235.05
Computation 215.17 4.36 Mops/sec, 4 threads
Lock Contention 258.98 11.14 Mlocks/sec, 4 threads
Memory Test 146.66
System 150.33
Allocate 117.80 432.61 Kalloc/sec
Fill 164.79 8012.48 MB/sec
Copy 185.21 3825.36 MB/sec
Stream 143.16
Copy 132.50 2736.68 MB/sec
Scale 134.42 2777.05 MB/sec
Add 155.53 3313.09 MB/sec
Triad 153.26 3278.67 MB/sec
Quartz Graphics Test 177.49
Line 150.04 9.99 Klines/sec [50% alpha]
Rectangle 182.58 54.51 Krects/sec [50% alpha]
Circle 176.48 14.39 Kcircles/sec [50% alpha]
Bezier 159.59 4.03 Kbeziers/sec [50% alpha]
Text 244.12 15.27 Kchars/sec
OpenGL Graphics Test 191.98
Spinning Squares 191.98 243.54 frames/sec
User Interface Test 467.06
Elements 467.06 2.14 Krefresh/sec

---

Going to OC this Bitch once I get new Mobo (Abit AW9D-MAX i975X) and PSU (be quiet! 700W straight power) - currently Asrock Conroe-XFire-eSATAII i945 (lacks Memory remapping above 3GB) and Enermax Coolergiant 485W (way underpowered, sys needs min 550W-600W).

Scores OCed past 3GHz should be interesting ...

CINEBENCH 9.5
****************************************************

Tester :

Processor : HackMac
MHz : 2410
Number of CPUs : 2
Operating System : 10.4.8

Graphics Card : nVidia 7600GS PCIe
Resolution :1600x1200
Color Depth : 32bpp

****************************************************

Rendering (Single CPU): 394 CB-CPU
Rendering (Multiple CPU): 725 CB-CPU

Multiprocessor Speedup: 1.84

Shading (CINEMA 4D) : 482 CB-GFX
Shading (OpenGL Software Lighting) : 1936 CB-GFX
Shading (OpenGL Hardware Lighting) : 4515 CB-GFX

OpenGL Speedup: 9.37

****************************************************
Results 131.17
System Info
Xbench Version 1.3
System Version 10.4.8 (8L2127)
Physical RAM 2048 MB
Model ACPI
Drive Type WDC WD2000JD-00HBB0
CPU Test 124.58
GCD Loop 282.05 14.87 Mops/sec
Floating Point Basic 135.89 3.23 Gflop/sec
vecLib FFT 100.66 3.32 Gflop/sec
Floating Point Library 88.75 15.45 Mops/sec
Thread Test 238.38
Computation 217.69 4.41 Mops/sec, 4 threads
Lock Contention 263.42 11.33 Mlocks/sec, 4 threads
Memory Test 153.59
System 144.13
Allocate 113.24 415.86 Kalloc/sec
Fill 178.29 8668.82 MB/sec
Copy 156.85 3239.72 MB/sec
Stream 164.39
Copy 153.17 3163.57 MB/sec
Scale 156.53 3233.93 MB/sec
Add 176.31 3755.88 MB/sec
Triad 174.12 3724.96 MB/sec
Quartz Graphics Test 179.09
Line 145.36 9.68 Klines/sec [50% alpha]
Rectangle 186.76 55.76 Krects/sec [50% alpha]
Circle 179.00 14.59 Kcircles/sec [50% alpha]
Bezier 159.62 4.03 Kbeziers/sec [50% alpha]
Text 260.90 16.32 Kchars/sec
OpenGL Graphics Test 171.75
Spinning Squares 171.75 217.87 frames/sec
Disk Test 64.09
Sequential 114.37
Uncached Write 119.58 73.42 MB/sec [4K blocks]
Uncached Write 102.78 58.15 MB/sec [256K blocks]
Uncached Read 130.21 38.11 MB/sec [4K blocks]
Uncached Read 108.66 54.61 MB/sec [256K blocks]
Random 44.52
Uncached Write 16.38 1.73 MB/sec [4K blocks]
Uncached Write 91.05 29.15 MB/sec [256K blocks]
Uncached Read 95.33 0.68 MB/sec [4K blocks]
Uncached Read 136.49 25.33 MB/sec [256K blocks]

Here's mine. This is OC'd to 3100@1066.


Results 191.15
System Info
Xbench Version 1.3
System Version 10.4.8 (8L2127)
Physical RAM 2048 MB
Model ACPI
Drive Type WDC WD2500JS-41MVB1
CPU Test 162.08
GCD Loop 366.45 19.32 Mops/sec
Floating Point Basic 177.55 4.22 Gflop/sec
vecLib FFT 131.01 4.32 Gflop/sec
Floating Point Library 115.15 20.05 Mops/sec
Thread Test 623.56
Computation 571.27 11.57 Mops/sec, 4 threads
Lock Contention 686.37 29.53 Mlocks/sec, 4 threads
Memory Test 201.76
System 189.25
Allocate 154.58 567.65 Kalloc/sec
Fill 202.71 9856.42 MB/sec
Copy 224.76 4642.23 MB/sec
Stream 216.03
Copy 203.83 4209.96 MB/sec
Scale 206.08 4257.64 MB/sec
Add 228.35 4864.25 MB/sec
Triad 228.42 4886.45 MB/sec
Quartz Graphics Test 259.31
Line 191.78 12.77 Klines/sec [50% alpha]
Rectangle 246.56 73.61 Krects/sec [50% alpha]
Circle 237.17 19.33 Kcircles/sec [50% alpha]
Bezier 212.57 5.36 Kbeziers/sec [50% alpha]
Text 916.90 57.36 Kchars/sec
OpenGL Graphics Test 227.17
Spinning Squares 227.17 288.18 frames/sec
User Interface Test 717.05
Elements 717.05 3.29 Krefresh/sec
Disk Test 70.23
Sequential 99.61
Uncached Write 103.64 63.63 MB/sec [4K blocks]
Uncached Write 101.61 57.49 MB/sec [256K blocks]
Uncached Read 83.49 24.43 MB/sec [4K blocks]
Uncached Read 115.10 57.85 MB/sec [256K blocks]
Random 54.24
Uncached Write 20.44 2.16 MB/sec [4K blocks]
Uncached Write 132.93 42.56 MB/sec [256K blocks]
Uncached Read 97.23 0.69 MB/sec [4K blocks]
Uncached Read 142.34 26.41 MB/sec [256K blocks]

CINEBENCH 9.5
****************************************************

Tester : Me

Processor : Macfrost
MHz : 3100
Number of CPUs : 4
Operating System : 10.4.8

Graphics Card : 7600GT Silent
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 514 CB-CPU
Rendering (Multiple CPU): 1680 CB-CPU

Multiprocessor Speedup: 3.27

Shading (CINEMA 4D) : 848 CB-GFX
Shading (OpenGL Software Lighting) : 2502 CB-GFX
Shading (OpenGL Hardware Lighting) : 5878 CB-GFX

OpenGL Speedup: 6.93

****************************************************

Overclocking work in progress. E6300 1.86GHz @ 2.8Ghz, complete specs in sig.


CINEBENCH 9.5
****************************************************

Tester : me

Processor : Hackintosh
MHz : 2800
Number of CPUs : 2
Operating System : Mac OS 10.4.8

Graphics Card : nVIDIA 7600GT
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 463 CB-CPU
Rendering (Multiple CPU): 851 CB-CPU

Multiprocessor Speedup: 1.84

Shading (CINEMA 4D) : 560 CB-GFX
Shading (OpenGL Software Lighting) : 2230 CB-GFX
Shading (OpenGL Hardware Lighting) : 5209 CB-GFX

OpenGL Speedup: 9.30

****************************************************



Xbench-no disk test: 222.05 Click to view attachment

I would say if your wanting a cheap rendering system any E4xxx/E6xxx will do just fine...Just one thing to note is if you can w8 until July the Q6600 wil drop to around USD$260 to USD $300 and offer performance either better or on par with the Quad G5s.

Intel xbx2 / xeon 3050 @ 3.0 Ghz /  Korsair KVR 800 @ 752Mhz _ 4-4-4-9 / XFX GeForce 7300 GT / W/O disk


Intel xbx2 / xeon 3050 @ 3.0 Ghz / Korsair KVR 800 @ 752 Mhz _ 4-4-4-9 / XFX GeForce 7300 GT / Seagate 7200.10 250 gb SATA


Intel xbx2 / xeon 3050 @ 3.0 Ghz / Korsair KVR 800 @ 752 Mhz _ 4-4-4-9 / XFX GeForce 7300 GT / Seagate 7200.7 200 gb IDE



also Geekbench:
Overall Score: 320.4

Specs: Intel Core 2 DUO E6600 overclocked to 3.4ghz
Idle temp: 29c-31c
Load temp: 48c-51c

Motherboard: Gigabyte 965P-DQ6
Ram: 2x1gb Corsair XMS2 DDR2@800mhz

Watercooled

Pics: http://forum.insanelymac.com/index.php?s=&...st&p=323999



CINEBENCH 9.5

Tester : Nykwil

Processor : Hackintosh G5
MHz : 3400
Number of CPUs : 2
Operating System : 10.4.8

Graphics Card : ATI X1950XTX
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************
Rendering (Single CPU): 545 CB-CPU
Rendering (Multiple CPU): 1006 CB-CPU

Multiprocessor Speedup: 1.85

Shading (CINEMA 4D) : 652 CB-GFX
Shading (OpenGL Software Lighting) : 2513 CB-GFX
Shading (OpenGL Hardware Lighting) : 5055 CB-GFX

OpenGL Speedup: 7.75

****************************************************


Xbench (with disk)

Results 175.12

System Info
Xbench Version 1.3
System Version 10.4.8 (8L2127)
Physical RAM 2048 MB
Model ADP2,1
Drive Type ST3500630AS
CPU Test 175.16
GCD Loop 394.37 20.79 Mops/sec
Floating Point Basic 192.23 4.57 Gflop/sec
vecLib FFT 142.85 4.71 Gflop/sec
Floating Point Library 123.48 21.50 Mops/sec
Thread Test 332.96
Computation 306.86 6.22 Mops/sec, 4 threads
Lock Contention 363.92 15.66 Mlocks/sec, 4 threads
Memory Test 201.16
System 225.26
Allocate 193.39 710.19 Kalloc/sec
Fill 230.42 11203.31 MB/sec
Copy 262.67 5425.31 MB/sec
Stream 181.71
Copy 168.09 3471.84 MB/sec
Scale 173.26 3579.43 MB/sec
Add 194.33 4139.71 MB/sec
Triad 194.33 4157.24 MB/sec
Quartz Graphics Test 250.38
Line 204.97 13.65 Klines/sec [50% alpha]
Rectangle 257.93 77.01 Krects/sec [50% alpha]
Circle 248.96 20.29 Kcircles/sec [50% alpha]
Bezier 223.33 5.63 Kbeziers/sec [50% alpha]
Text 367.66 23.00 Kchars/sec
OpenGL Graphics Test 272.97
Spinning Squares 272.97 346.28 frames/sec
User Interface Test 710.06
Elements 710.06 3.26 Krefresh/sec
Disk Test 58.06
Sequential 111.55
Uncached Write 84.75 52.03 MB/sec [4K blocks]
Uncached Write 138.18 78.18 MB/sec [256K blocks]
Uncached Read 123.27 36.07 MB/sec [4K blocks]
Uncached Read 114.81 57.70 MB/sec [256K blocks]
Random 39.25
Uncached Write 13.00 1.38 MB/sec [4K blocks]
Uncached Write 133.96 42.89 MB/sec [256K blocks]
Uncached Read 91.57 0.65 MB/sec [4K blocks]
Uncached Read 151.15 28.05 MB/sec [256K blocks]


Xbench (no disk)

Results 265.80

System Info
Xbench Version 1.3
System Version 10.4.8 (8L2127)
Physical RAM 2048 MB
Model ADP2,1
Drive Type ST3500630AS
CPU Test 173.35
GCD Loop 393.71 20.75 Mops/sec
Floating Point Basic 190.27 4.52 Gflop/sec
vecLib FFT 138.55 4.57 Gflop/sec
Floating Point Library 124.05 21.60 Mops/sec
Thread Test 334.01
Computation 305.15 6.18 Mops/sec, 4 threads
Lock Contention 368.90 15.87 Mlocks/sec, 4 threads
Memory Test 192.75
System 206.63
Allocate 157.01 576.58 Kalloc/sec
Fill 231.38 11250.00 MB/sec
Copy 261.27 5396.45 MB/sec
Stream 180.62
Copy 166.20 3432.77 MB/sec
Scale 173.37 3581.81 MB/sec
Add 194.05 4133.68 MB/sec
Triad 192.02 4107.87 MB/sec
Quartz Graphics Test 275.96
Line 205.53 13.68 Klines/sec [50% alpha]
Rectangle 262.94 78.50 Krects/sec [50% alpha]
Circle 251.42 20.49 Kcircles/sec [50% alpha]
Bezier 225.74 5.69 Kbeziers/sec [50% alpha]
Text 959.49 60.02 Kchars/sec
OpenGL Graphics Test 272.73
Spinning Squares 272.73 345.97 frames/sec
User Interface Test 750.49
Elements 750.49 3.44 Krefresh/sec


Overall Geekbench Score : 4413

hahaha
My c2d at idle is 14C-15C and at full load is 40C-42C on passive cooling! (non overclocked also)

BTW- Xbench is a freaking joke, use geekbench2 and OpenMark and Cinebench

-DiaboliK
(Geekbench 2 benches)

1st of all, you have a 2ghz c2d.
2nd of all, you didn't factor in a warm room (my room is 80+ degrees in the winter time, and i cant control that) I"d like to see how warm YOUR room is.
3rd, considering i gained a 1ghz overclock for free using water with fans running at super low speeds of 1200 rpm at a silent 17db pushing 45cfms vs your temps at passive and not being actively cooled, it's nothing to laugh at.

your geekbenches however, I WILL laught at:

ambient room temp is 70F. and theres one fan in that system 1 40mm nidec betaV fan, when wrapped up in a g4 cube case its virtually silent

as for my benches, i dont really care. i dont need all that power sucking my power bill!

the benches that are up there are just 2 of my computers i run here at my house, just to play around with and not acutally do real work other than graphic design and other stuff.

your benches are nice, higher than kiko's, but i still dont care

-DiaboliK

yeah i dont care much for benches...nor my temps...it's all within limits. I dont notice any speed increases in todays high speed cpus anyway.

long as my media doesnt hiccup or lag when im doing mutiple things at once i'm fine

CINEBENCH 9.5
****************************************************

Tester : NapalmCandy

Processor : Core 2 Duo e6600
MHz : 3339
Number of CPUs : 2
Operating System : OSX 1.4.9

Graphics Card : Radeon x300
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 555 CB-CPU
Rendering (Multiple CPU): 1055 CB-CPU

Multiprocessor Speedup: 1.90

Shading (CINEMA 4D) : 677 CB-GFX
Shading (OpenGL Software Lighting) : 2554 CB-GFX
Shading (OpenGL Hardware Lighting) : 2724 CB-GFX

OpenGL Speedup: 4.02

****************************************************

specs in sig

CINEBENCH 9.5
****************************************************

Tester :

Processor : Pentium D 805
MHz : 3600
Number of CPUs : 2
Operating System : OSX 10.4.8

Graphics Card : ATI Radeon 9800XT
Resolution :
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 303 CB-CPU
Rendering (Multiple CPU): 542 CB-CPU

Multiprocessor Speedup: 1.79

Shading (CINEMA 4D) : 383 CB-GFX
Shading (OpenGL Software Lighting) : 1236 CB-GFX
Shading (OpenGL Hardware Lighting) : 1487 CB-GFX

OpenGL Speedup: 3.88

****************************************************

CINEBENCH 9.5
****************************************************

Tester :

Processor :
MHz :
Number of CPUs : 2
Operating System :

Graphics Card :
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 511 CB-CPU
Rendering (Multiple CPU): 938 CB-CPU

Multiprocessor Speedup: 1.84

Shading (CINEMA 4D) : 629 CB-GFX
Shading (OpenGL Software Lighting) : 2541 CB-GFX
Shading (OpenGL Hardware Lighting) : 5881 CB-GFX

OpenGL Speedup: 9.35

****************************************************

CINEBENCH R10
****************************************************

Tester :

Processor :
MHz :
Number of CPUs : 4
Operating System : OS X 32 BIT 10.4.9

Graphics Card : ATI Radeon X1900 OpenGL Engine
Resolution : <fill this out>
Color Depth : <fill this out>

****************************************************

Rendering (Single CPU): 4056 CB-CPU
Rendering (Multiple CPU): 13862 CB-CPU

Multiprocessor Speedup: 3.42

Shading (OpenGL Standard) : 7749 CB-GFX


****************************************************

see my sig ..

also below is xbench without disk as is fashion in this thread.

Results 305.82
System Info
Xbench Version 1.3
System Version 10.5 (9A581)
Physical RAM 4096 MB
Model ACPI
Drive Type WDC WD740GD-00FLA2
CPU Test 208.39
GCD Loop 425.27 22.42 Mops/sec
Floating Point Basic 206.65 4.91 Gflop/sec
vecLib FFT 165.90 5.47 Gflop/sec
Floating Point Library 167.33 29.14 Mops/sec
Thread Test 340.34
Computation 322.35 6.53 Mops/sec, 4 threads
Lock Contention 360.47 15.51 Mlocks/sec, 4 threads
Memory Test 258.39
System 309.71
Allocate 479.30 1.76 Malloc/sec
Fill 248.39 12077.12 MB/sec
Copy 279.79 5778.87 MB/sec
Stream 221.66
Copy 211.68 4372.20 MB/sec
Scale 209.08 4319.57 MB/sec
Add 233.94 4983.33 MB/sec
Triad 234.51 5016.73 MB/sec
Quartz Graphics Test 351.91
Line 280.14 18.65 Klines/sec [50% alpha]
Rectangle 378.92 113.13 Krects/sec [50% alpha]
Circle 302.09 24.62 Kcircles/sec [50% alpha]
Bezier 291.68 7.36 Kbeziers/sec [50% alpha]
Text 793.27 49.62 Kchars/sec
OpenGL Graphics Test 284.47
Spinning Squares 284.47 360.87 frames/sec
User Interface Test 604.06
Elements 604.06 2.77 Krefresh/sec

Results 227.77
System Info
Xbench Version 1.3
System Version 10.5.1 (9B18)
Physical RAM 4096 MB
Model Mac Pro
Drive Type Maxtor 3H500F0
CPU Test 184.17
GCD Loop 377.63 19.91 Mops/sec
Floating Point Basic 182.79 4.34 Gflop/sec
vecLib FFT 146.47 4.83 Gflop/sec
Floating Point Library 147.64 25.71 Mops/sec
Thread Test 311.04
Computation 292.93 5.93 Mops/sec, 4 threads
Lock Contention 331.53 14.26 Mlocks/sec, 4 threads
Memory Test 253.78
System 282.07
Allocate 355.42 1.31 Malloc/sec
Fill 237.83 11564.04 MB/sec
Copy 276.43 5709.65 MB/sec
Stream 230.65
Copy 211.71 4372.77 MB/sec
Scale 220.61 4557.79 MB/sec
Add 247.58 5274.06 MB/sec
Triad 247.11 5286.38 MB/sec
Quartz Graphics Test 307.42
Line 236.96 15.78 Klines/sec [50% alpha]
Rectangle 329.92 98.50 Krects/sec [50% alpha]
Circle 266.84 21.75 Kcircles/sec [50% alpha]
Bezier 254.91 6.43 Kbeziers/sec [50% alpha]
Text 744.63 46.58 Kchars/sec
OpenGL Graphics Test 271.50
Spinning Squares 271.50 344.42 frames/sec
User Interface Test 540.93
Elements 540.93 2.48 Krefresh/sec
Disk Test 106.81
Sequential 122.52
Uncached Write 119.66 73.47 MB/sec [4K blocks]
Uncached Write 118.12 66.83 MB/sec [256K blocks]
Uncached Read 133.66 39.12 MB/sec [4K blocks]
Uncached Read 119.85 60.24 MB/sec [256K blocks]
Random 94.68
Uncached Write 93.83 9.93 MB/sec [4K blocks]
Uncached Write 94.88 30.37 MB/sec [256K blocks]
Uncached Read 80.10 0.57 MB/sec [4K blocks]
Uncached Read 116.71 21.66 MB/sec [256K blocks]

Geekbench Score 6866

version Geekbench 2.0.9
Platform Mac OS X x86 (32-bit)
Operating System Mac OS X 10.5.1 (Build 9B18)
Processor Intel® Core™2 Quad CPU Q6600 @ 2.40GHz
Model Hackintosh
Memory 4.00 GB 800 MHz RAM
Integer Score 6438

Blowfish
single-threaded scalar 2989
131.3 MB/sec

Blowfish
multi-threaded scalar 12675
519.4 MB/sec

Text Compress
single-threaded scalar 2930
9.37 MB/sec

Text Compress
multi-threaded scalar 10684
35.0 MB/sec

Text Decompress
single-threaded scalar 2763
11.4 MB/sec

Text Decompress
multi-threaded scalar 10350
41.2 MB/sec

Image Compress
single-threaded scalar 2498
20.6 Mpixels/sec

Image Compress
multi-threaded scalar 9524
80.1 Mpixels/sec

Image Decompress
single-threaded scalar 2122
35.6 Mpixels/sec

Image Decompress
multi-threaded scalar 7812
127.5 Mpixels/sec

Crafty Chess
single-threaded scalar 3053
1.54 Mnodes/sec

Crafty Chess
multi-threaded scalar 3179
1.54 Mnodes/sec

Lua
single-threaded scalar 4132
1.59 Mnodes/sec

Lua
multi-threaded scalar 15430
5.94 Mnodes/sec

Floating Point Score 10227

Mandelbrot
single-threaded scalar 2693
1.79 Gflops

Mandelbrot
multi-threaded scalar 10287
6.73 Gflops

Dot Product
single-threaded scalar 4243
2.05 Gflops

Dot Product
multi-threaded scalar 13634
6.21 Gflops

Dot Product
single-threaded vector 2950
3.53 Gflops

Dot Product
multi-threaded vector 8763
9.11 Gflops

LU Decomposition
single-threaded scalar 1060
943.8 Mflops

LU Decomposition
multi-threaded scalar 4100
3.60 Gflops

Primality Test
single-threaded scalar 5154
769.8 Mflops

Primality Test
multi-threaded scalar 14876
2.76 Gflops

Sharpen Image
single-threaded scalar 7206
16.8 Mpixels/sec

Sharpen Image
multi-threaded scalar 25027
57.7 Mpixels/sec

Blur Image
single-threaded scalar 9374
7.42 Mpixels/sec

Blur Image
multi-threaded scalar 33822
26.6 Mpixels/sec

Memory Score 3763

Read Sequential
single-threaded scalar 4818
5.90 GB/sec

Write Sequential
single-threaded scalar 4110
2.81 GB/sec

Stdlib Allocate
single-threaded scalar 2946
11.0 Mallocs/sec

Stdlib Write
single-threaded scalar 3607
7.47 GB/sec

Stdlib Copy
single-threaded scalar 3336
3.44 GB/sec

Stream Score 2815

Stream Copy
single-threaded scalar 2835
3.88 GB/sec

Stream Copy
single-threaded vector 3069
3.98 GB/sec

Stream Scale
single-threaded scalar 2903
3.77 GB/sec

Stream Scale
single-threaded vector 2929
3.95 GB/sec

Stream Add
single-threaded scalar 2548
3.85 GB/sec

Stream Add
single-threaded vector 3139
4.37 GB/sec

Stream Triad
single-threaded scalar 2798
3.87 GB/sec

Stream Triad
single-threaded vector 2302
4.31 GB/sec

System Information
Platform Mac OS X x86 (32-bit)
Compiler GCC 4.0.1 (Apple Inc. build 5465)
Operating System Mac OS X 10.5.1 (Build 9B18)
Model Hackintosh
Motherboard Mac Pro
Processor Intel® Core™2 Quad CPU Q6600 @ 2.40GHz
Processor ID GenuineIntel Family 6 Model 15 Stepping 11
Logical Processors 4
Physical Processors 1
Processor Frequency 3.60 GHz
L1 Instruction Cache 32.0 KB
L1 Data Cache 32.0 KB
L2 Cache 4.00 MB
L3 Cache 0.00 B
Bus Frequency 1.80 GHz
Memory 4.00 GB
Memory Type 800 MHz RAM
SIMD 1

not bad for a C2D laptop..


Results 110.88
System Info
Xbench Version 1.3
System Version 10.5.1 (9B18)
Physical RAM 2048 MB
Model Mac Pro
Drive Type ST980813AS
CPU Test 126.31
GCD Loop 258.61 13.63 Mops/sec
Floating Point Basic 123.99 2.95 Gflop/sec
vecLib FFT 101.21 3.34 Gflop/sec
Floating Point Library 101.46 17.67 Mops/sec
Thread Test 207.18
Computation 191.53 3.88 Mops/sec, 4 threads
Lock Contention 225.63 9.71 Mlocks/sec, 4 threads
Memory Test 156.07
System 163.66
Allocate 253.54 931.07 Kalloc/sec
Fill 134.54 6541.50 MB/sec
Copy 143.81 2970.27 MB/sec
Stream 149.15
Copy 140.30 2897.74 MB/sec
Scale 144.83 2992.06 MB/sec
Add 156.52 3334.22 MB/sec
Triad 156.31 3343.80 MB/sec
Quartz Graphics Test 155.11
Line 128.34 8.54 Klines/sec [50% alpha]
Rectangle 151.28 45.17 Krects/sec [50% alpha]
Circle 123.14 10.04 Kcircles/sec [50% alpha]
Bezier 140.69 3.55 Kbeziers/sec [50% alpha]
Text 383.98 24.02 Kchars/sec
OpenGL Graphics Test 111.03
Spinning Squares 111.03 140.84 frames/sec
User Interface Test 220.92
Elements 220.92 1.01 Krefresh/sec
Disk Test 41.67
Sequential 86.47
Uncached Write 88.43 54.30 MB/sec [4K blocks]
Uncached Write 85.76 48.52 MB/sec [256K blocks]
Uncached Read 91.53 26.79 MB/sec [4K blocks]
Uncached Read 80.90 40.66 MB/sec [256K blocks]
Random 27.45
Uncached Write 8.65 0.92 MB/sec [4K blocks]
Uncached Write 87.99 28.17 MB/sec [256K blocks]
Uncached Read 91.17 0.65 MB/sec [4K blocks]
Uncached Read 127.46 23.65 MB/sec [256K blocks]

Processor : Core2Duo E8400
MHz : 3000
Number of CPUs : 2
Operating System : 10.4.8JAS

Graphics Card : 7600GT
Resolution : 1400x1050
Color Depth : 24bit

****************************************************
Cinebench 9.5

Rendering (Single CPU): 547 CB-CPU
Rendering (Multiple CPU): 1011 CB-CPU

Multiprocessor Speedup: 1.85

Shading (CINEMA 4D) : 647 CB-GFX
Shading (OpenGL Software Lighting) : 2601 CB-GFX
Shading (OpenGL Hardware Lighting) : 5848 CB-GFX

OpenGL Speedup: 9.04
****************************************************
Cinebench R10

Rendering (Single CPU): 3429 CB-CPU
Rendering (Multiple CPU): 6508 CB-CPU

Multiprocessor Speedup: 1.90

Shading (OpenGL Standard) : 5299 CB-GFX

Click to view attachment

Sorry, don't have a screen or the full scores, but my final score without disk was 229. That's for the machine in my sig (P35-DS3P)

xbench is not an accurate benchmarking tool.

its like using a park bench and calling it a couch. it may seem that is working but guess what, it isnt.

xbench will vary your benches by just resizing the window!!

for example your res is set to 800x600 bench in xbench and you get a high score.
set it to 1024x768 and the bench will decrease.

with that said... use a better set of benchmarking tools.

geekbench : http://primatelabs.ca
openGL extensions veiwer: http://www.realtech-vr.com/glview/
openmark: http://www.mediafire.com/?m4gy91tsge0
cinebench: http://www.maxon.net/pages/download/cinebench_e.html

-D-