Jump to content

Dell Inspiron 14R E596 (N4010) with Intel HD graphics


Christoff
 Share

58 posts in this topic

Recommended Posts

Please Help! i have a Dell 14R N4010 notebook have tried iatkos S3 , partially working (cant get graphics) with retail canoot boot without boot cd , and hazard cannot start Instalation busratio is 17 by the way.Anyone could get Intel HD graphics with Quartz extreme and full resolution? need it for Logic 9 mainly

Specs:

 

QUOTE

Dell 14R touchpad

Dell 14R features a Samsung screen.

camera

two 14R wireless antennas

Core i5 430M processor

N4010 HD 5470 discrete graphics

14R PCH chip

Dell Inspiron 14R Dual DDR3 memory slots (4 GB 1066)

card reader and Bluetooth module

hard disk and CD-ROM SATA Interface

N4010 ATHEROS AR8152 LAN chip

REALTEK ALC269 CODEC chip

N4010 Mini PCIE slot for the installation of wireless LAN equipment

 

Dell Page With drivers http://search.dell.com/results.aspx?spf ... srch=False

 

Please Help!

Thanks!

Christoff

PD:im aNewbie

Link to comment
Share on other sites

Have you tried [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] + [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]?

Link to comment
Share on other sites

Let's see if we can keep this going...I've tried both so far w/o success, but I'm determined to get this going. btw - just fyi here's my specs (a little different)

 

Inspiron 14r

 

core i3 (350m)

 

(hm57 chipset)

 

4gb ddr3 1333mhz ram

 

500 gb seagate barracuda (7200rpm) (insane upgrade - took me forever)

 

dell 365 bluetooth (this will be no prob)

 

dell wireless-n 1501 (not sure about this - shouldn't be a problem....believe it's broadcom)

 

I think the rest is pretty much the same for any inspiron 14r, or 15 or 17 for that matter.

 

Anyway, easyefi didn't work at all for me - not sure what's wrong there....but I'll keep trying and posting...please keep us in the loop with your results too.

 

thanks!

Link to comment
Share on other sites

HAve no luck either, the only way it worked was with empire Efi + Retail 10.6.0, but have to keep the disc in the drive to boot , the post instalation didnt worked for me, and when i make an updtae , with update combo i get Kernel panic, iopcplatform i think (installing the easy efi also gave me Kernel Panic.

Wi Fi is Broadcom 47xx it doesnt work, sound, voodoo HDA , Track pad ,works , Camera Works, Ethernet Works with Atlansic L1e Kext, Sleep Doesnt and Video Doesnt.(need to unpack Easy efi and post Kext Here)

Keep in touch! Bye!

Link to comment
Share on other sites

HAve no luck either, the only way it worked was with empire Efi + Retail 10.6.0, but have to keep the disc in the drive to boot , the post instalation didnt worked for me, and when i make an updtae , with update combo i get Kernel panic, iopcplatform i think (installing the easy efi also gave me Kernel Panic.

Wi Fi is Broadcom 47xx it doesnt work, sound, voodoo HDA , Track pad ,works , Camera Works, Ethernet Works with Atlansic L1e Kext, Sleep Doesnt and Video Doesnt.(need to unpack Easy efi and post Kext Here)

Keep in touch! Bye!

 

same here, I used [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and I can install, but when I run [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and restart, it wont boot. The only way it boots is with the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] cd. Also when I run 10.6.3 it gets about 75% installed then kernel panic. Once that happens even [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] can't get it to boot.

 

(10.6.2 installed it would still boot with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url])

 

i3 350, intel HD graphics

 

acer 5741 laptop

Link to comment
Share on other sites

same here, I used [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and I can install, but when I run [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and restart, it wont boot. The only way it boots is with the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] cd. Also when I run 10.6.3 it gets about 75% installed then kernel panic. Once that happens even [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] can't get it to boot.

 

(10.6.2 installed it would still boot with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url])

 

i3 350, intel HD graphics

 

acer 5741 laptop

 

 

i just looked at the list of various core processors on tonymac's blog, it turns out the 350m isn't supported (but doing a little search here in insanely mac, one user reported success using iatkos s3) I'm not giving up though...still searching and reading

Link to comment
Share on other sites

ok, for whatever reason extra folder was empty, and I learned that if you replace the extra folder after you install multiboot (even though install fails)...it will then boot. Worked for me....now on to the rest of the kexts......

 

(the previous extra folder was just empty ????) anyway - we're getting somewhere...at least I can boot w/o cd now

 

next step was to use the file from the nowalleasy blogspot and choose what you want to install.....success # 2......moving along (of course I'm still only on 10.6.0, but getting somewhere nonetheless) Hope this helps you guys....

Link to comment
Share on other sites

yup i3 350m isn't supported, but it did boot and work with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]. What kext's need to go into the extra folder to boot?

I'll give it another go and make sure to stop at 10.6.2

Link to comment
Share on other sites

well, I literally just 'drag and drop' replaced the whole extra folder from the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] cd to my hd and it worked, the kexts needed for the extensions folder you could grab from the easyefi2.1 iso - he put a million in there, and perhaps use kext utility or kext helper, but so far I'm still struggling to get it going...hope this helps, and keep us posted on your progress...thanks!

 

(I'm still researching which specific kexts, but the ethernet one you can get - just google 'iats google code' - that's one any way, and I can confirm it works (the ethernet controller is atheros ar8152) - the rest I'm still trying to figure out

Link to comment
Share on other sites

same here, I used [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and I can install, but when I run [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and restart, it wont boot. The only way it boots is with the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] cd. Also when I run 10.6.3 it gets about 75% installed then kernel panic. Once that happens even [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] can't get it to boot.

 

(10.6.2 installed it would still boot with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url])

 

i3 350, intel HD graphics

 

acer 5741 laptop

 

Can't install 10.6.2....any tricks? (Keep getting the message "doesn't meet requirements to install on this volume" - something like that...

Link to comment
Share on other sites

Can't install 10.6.2....any tricks? (Keep getting the message "doesn't meet requirements to install on this volume" - something like that...

 

 

hmm, I installed it by first installing OSX using [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url], then I ran the 10.6.2 installer, then restarted using [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] as the boot cd again.

Link to comment
Share on other sites

iatkos s3 appears to be the way to go with the qoopz 10.3 kernel selected...loading right now, and will post results; however this still doesn't resolve the op's dilemma about resolution - still not sure how to get this right...

 

we'll keep tryin'

Link to comment
Share on other sites

yup, iatkos s3 v1 (v2 is available too), with the busratio=17, or whatever # fits your processor = working/booting 106.3 install!!!!

 

Great stuff - now on to the rest of the kexts (I still need wireless and bluetooth - not sure yet, oh yes, and resolution - I think this should be out here somewhere though)

 

Let us know what works for you all......

Link to comment
Share on other sites

yup, iatkos s3 v1 (v2 is available too), with the busratio=17, or whatever # fits your processor = working/booting 106.3 install!!!!

 

Great stuff - now on to the rest of the kexts (I still need wireless and bluetooth - not sure yet, oh yes, and resolution - I think this should be out here somewhere though)

 

Let us know what works for you all......

Yes, i tried Retail but only got 10.6.0 without updates or graphics,and also without Wi fi , the rest was ok.

Ill try with iatkos S3 V2 , for intel HD we could try the Kext from Easyefi.

Ill keep in touch!

Bye!

Link to comment
Share on other sites

Hey guys any luck? I am really good with windblows but a complete idiot with osx. I am trying to make the switch over but don't have any ideas how to troubleshoot. I also have an N4010. Mine has the i3 M350, and integrated HD graphics. Any suggestions? Let's keep this one going. I know a lot of people are getting this laptop.

Link to comment
Share on other sites

Is there anyone on here?

 

Please Help! i have a Dell 14R N4010 notebook have tried iatkos S3 , partially working (cant get graphics) with retail canoot boot without boot cd , and hazard cannot start Instalation busratio is 17 by the way.Anyone could get Intel HD graphics with Quartz extreme and full resolution? need it for Logic 9 mainly

Specs:

 

QUOTE

Dell 14R touchpad

Dell 14R features a Samsung screen.

camera

two 14R wireless antennas

Core i5 430M processor

N4010 HD 5470 discrete graphics

14R PCH chip

Dell Inspiron 14R Dual DDR3 memory slots (4 GB 1066)

card reader and Bluetooth module

hard disk and CD-ROM SATA Interface

N4010 ATHEROS AR8152 LAN chip

REALTEK ALC269 CODEC chip

N4010 Mini PCIE slot for the installation of wireless LAN equipment

 

Dell Page With drivers http://search.dell.com/results.aspx?spf ... srch=False

 

Please Help!

Thanks!

Christoff

PD:im aNewbie

Link to comment
Share on other sites

I just bought a Dell Inspiron 14R N4010 and I have no clue were to begin.

 

I tried [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] + iAtkos S2 v3, managed to install but after that it woun't boot. I don't know what options I should select on Options. Can anyone help me please?

 

I also tried EmpireEFI but the notebook won't even boot from this disc.

Link to comment
Share on other sites

I have the same laptop.

 

i3 m350, with HD intel graphics card.

Ive been using kalaway 10.5.1, i can get it installed but on the bootup i always get b0 error, and i cant manage to get the bootloader to work. im going to try making the whole HDD mac, no other partitions, no bual booting, nothing.

Link to comment
Share on other sites

 Share

×
×
  • Create New...