Samsung NC10 UK revision, Updates / Installation / Modding etc, stuff will be here Options

[Enlightx]

hi guys need help been trying to get this working now for over 2 days

got NC-10 UK

followed the guide fully and when i get to the upgrade part i follow it to the letter. on the reboot (after stage 3) mac grey logo pop up then hard reset to samsung screen.

i have also tried with the deneb 10.5 disc and i get the same thing but strait after installs 1st reboot.

any ideas this is driving me up the wall.

system is fully stock other then 2GB RAM

[ Mysticus C*]

hi guys need help been trying to get this working now for over 2 days

got NC-10 UK

followed the guide fully and when i get to the upgrade part i follow it to the letter. on the reboot (after stage 3) mac grey logo pop up then hard reset to samsung screen.

i have also tried with the deneb 10.5 disc and i get the same thing but strait after installs 1st reboot.

any ideas this is driving me up the wall.

system is fully stock other then 2GB RAM

did you check page 54 for bios settings as well?

[Enlightx]

yeah all bios settings are correct i will triple check them again though. any other ideas ?

[G4-Flo]

i m not sure it is wise to use 10.4 for all the works done already for this nc10... leopard is running just fine... why do you wanna downgrade?

just get Jas 10.5.4 dvd, and use my ppf, you will have one stop install everything...

Well, I thought that 10.4.x might be running faster than 10.5, thats why I was asking. But if you say that there is no difference in performance I will install 10.5.

At this time I don't have the Dell wifi-card. Is there a problem installing the OS first and exchanging the atheros with dell later?

[ Mysticus C*]

Well, I thought that 10.4.x might be running faster than 10.5, thats why I was asking. But if you say that there is no difference in performance I will install 10.5.

At this time I don't have the Dell wifi-card. Is there a problem installing the OS first and exchanging the atheros with dell later?

nope there is no problem doing that...

[Enlightx]

Mysticus C* thanks m8 you were right i had missed out 1 of the bios settings even after double checking lol

keep up the good work

your the man !!!!!!!

[ Mysticus C*]

Mysticus C* thanks m8 you were right i had missed out 1 of the bios settings even after double checking lol

keep up the good work

your the man !!!!!!!

no problem... i told u so, many people forget to check that page carefully!

[darkgemini]

new 1.1.0 update package is ready, with fixed ps/2 drivers that does not cause crazy mouse issue...

power connected sleep issue remains... still testing different things.. (most likely acpi issue)
battery sleep works fine...

unfortunately upgrade dvd is on hold for now, until i figure out the Glob.pm perl issue... which is bugging me bad

darkgemini: have u read the guide? partition schemes and bios settings are all explained... also have u checked the md5 of the nc10 iso?

dontbeef: new package contains working better ps2 driver...

I just checked the md5 checksum, it turned out that it didn't match yours. Both the original Jas and NC10 didn't match yours md5. So, I guess I have to download Jas from your website then....sigh...hate RapidShare waiting time...

[ Mysticus C*]

I just checked the md5 checksum, it turned out that it didn't match yours. Both the original Jas and NC10 didn't match yours md5. So, I guess I have to download Jas from your website then....sigh...hate RapidShare waiting time...

before you download anything, i need to tell you that not all md5 programs calculate md5 correctly!

for windows: use a program called accuhash
for mac: use built-in terminal and type: md5 file.name

[jdenbrok]

Hi, I am sorry for my ruthness as I have not read all pages in this threath before writing here my first post. I am following your work already longer and I just found http://forum.insanelymac.com/index.php?showtopic=138351
I am not sure if you have seen this. When this will be in the package?
Cant wait to find some spare time and install osx in my nc10.

[ Mysticus C*]

Hi, I am sorry for my ruthness as I have not read all pages in this threath before writing here my first post. I am following your work already longer and I just found http://forum.insanelymac.com/index.php?showtopic=138351
I am not sure if you have seen this. When this will be in the package?
Cant wait to find some spare time and install osx in my nc10.

it has been mentioned many times...

most likley it will not be in the package due to following reasons:

the method is merely a new driver... rather a workaround...
it is more trouble and less reliable... although it works in the end...
it will give me and others so much headache trying to give instructions on people who have no clue about what they are doing...
if you read it carefully, it will give u lotsa KPs and will work after some trials... also dont forget you have to run the kismac and close it before you can use the wifi...

long story short, it is trouble for noobs and experienced users to debug noobs inability to get it to work due to nature of the method... if official drivers or somewhat patched more stable and less troublesome comes out, i ll include it, else, nope...

[myi4u]

hi mysticus c*,

once you replaced your atheros wifi card, will it be en0 or en1 for the new card?

[ Mysticus C*]

hi mysticus c*,

once you replaced your atheros wifi card, will it be en0 or en1 for the new card?

if it is recognized it should be en0 auto... but in future if lan gets recognized as well, it may change the order...

[myi4u]

if it is recognized it should be en0 auto... but in future if lan gets recognized as well, it may change the order...

hi, sorry... i meant to ask whether your wifi card is on en0 or en1 now?

[ Mysticus C*]

UPDATE NEWS!
=============

Ladies and Gents.... I can announce now that I overcome the 10.5.5 update issue caused by the glob.pm thingy... it installed and running perfectly...

Now i know the reason (partitally , because i didnt extensively check the entire content individually but it works now), the problem is solved... ...

Expect the OTB 10.5.5 NC10 dvd upgrade procedure soon... later i can even provide the OTB 10.5.6 upgrade procedure...

Now problematic part solved.... I can make my script to convert your 10.5.4 nc10 dvd iso to a 10.5.5 and later 10.5.6 OTB cool ey?

Note: Dont get confused about 10.5.5 update thing i mentioned above, it is related to making the dvd 10.5.5 OTB so you dont need to update it when you needed to install it..... Current one is working, but now I made another progress which will make it even better! You will have 10.5.5 OTB and everything working OTB... apart from teh known issues...

What is next?

+ Prepare the scripts and files for 10.5.5 dvd iso upgrade... (for this you will need to have osx running first... and download 10.5.5 combo update, and put it in the project directory... more info will given later... ppf is another alternative however, it will be a 600mb ppf due to the 10.5.5 combo package which i dont really wanna do but who knows i may do it...)

+ Will still need to edit the post#1 which i didnt do yet...

+ Modify the current guide for the ddmac procedure... sorry it took long, but 10.5.5 procedure was bugging me...

more news later...

myi4u: it is en0 first recognized gets the first enX address

[RealRooster]

I have been using my new NC10 for a few days now.
Dell 1390 and 2 Gb RAM have been installed and OS X 10.5.5 is running quite nicely.

Somewhere earlier in this topic the following has been mentioned:
"headphone switching works with only script + CHUD package installed, programs unfortunately not working at the moment..."

So, where I can find that script you're talking about?

Audieee + CHUD is currently installed, but unfortunately that combination is not working with the headphones.

Thanks in advance and keep up the good work.

[ Mysticus C*]

I have been using my new NC10 for a few days now.
Dell 1390 and 2 Gb RAM have been installed and OS X 10.5.5 is running quite nicely.

Somewhere earlier in this topic the following has been mentioned:
"headphone switching works with only script + CHUD package installed, programs unfortunately not working at the moment..."

So, where I can find that script you're talking about?

Audieee + CHUD is currently installed, but unfortunately that combination is not working with the headphones.

Thanks in advance and keep up the good work.

i will provide the solution soon mate, be patient... i ve been busy with my personal stuffs and lately this upgrade dvd as well, didnt have too much time to put together a better info and packages

but soon i ll manage to do all of those...

[darkgemini]

Yeahhhh, I finally manage to install it...it's installing right now...I ended up re-download the Jas from the torrent site again and Force Re-Check it to make sure I get all the pieces...It works this time

[ Mysticus C*]

Yeahhhh, I finally manage to install it...it's installing right now...I ended up re-download the Jas from the torrent site again and Force Re-Check it to make sure I get all the pieces...It works this time

damaged download i guess? bad md5=damaged iso

[darkgemini]

Mysticus, should I update to 10.5.5 with the NC 1.0 Installer now or wait for your NC1.1.0? Since it has many enhanced fixed
If I update it now, will I still able to use NC10 1.1.0 Installer?